I was not aware Wireshark worked on PRI spans. What interface should I tell it to watch? 8-|
Card is: wanpipe: AFT-A101-SH PCI T1/E1 card found (HDLC (DS) rev.37), cpu(s) 1 chan_dahdi.conf has a timestamp of Jun 25 of last year # cat /etc/asterisk/chan_dahdi.conf ;autogenerated by /usr/sbin/wancfg_dahdi do not hand edit ;autogenrated on 2012-05-29 ;Dahdi Channels Configurations ;For detailed Dahdi options, view /etc/asterisk/chan_dahdi.conf.bak [trunkgroups] [channels] usecallerid=yes echocancel=yes echocancelwhenbridged=yes rxgain=0.0 txgain=0.0 group=1 immediate=no pridialplan=unknown resetinterval=never ;Sangoma A101 port 1 [slot:2 bus:17 span:1] <wanpipe1> switchtype=national context=pbxmax group=1 echocancel=yes signalling=pri_cpe channel =>1-23 PRI debug: seidelnj*CLI> pri debug span 1 Enabled debugging on span 1 TEI=0 Got SABME from network peer. TEI=0 Sending UA TEI=0 MDL-ERROR (F): SABME in state 7(Multi-frame established) TEI=0 Got SABME from network peer. TEI=0 Sending UA TEI=0 MDL-ERROR (F): SABME in state 7(Multi-frame established) TEI=0 Got SABME from network peer. TEI=0 Sending UA TEI=0 MDL-ERROR (F): SABME in state 7(Multi-frame established) TEI=0 Got SABME from network peer. TEI=0 Sending UA TEI=0 MDL-ERROR (F): SABME in state 7(Multi-frame established) TEI=0 Got SABME from network peer. TEI=0 Sending UA TEI=0 MDL-ERROR (F): SABME in state 7(Multi-frame established) TEI=0 Got SABME from network peer. TEI=0 Sending UA TEI=0 MDL-ERROR (F): SABME in state 7(Multi-frame established) TEI=0 Got SABME from network peer. TEI=0 Sending UA TEI=0 MDL-ERROR (F): SABME in state 7(Multi-frame established) TEI=0 Got SABME from network peer. TEI=0 Sending UA TEI=0 MDL-ERROR (F): SABME in state 7(Multi-frame established) TEI=0 Got SABME from network peer. TEI=0 Sending UA TEI=0 MDL-ERROR (F): SABME in state 7(Multi-frame established) TEI=0 Got SABME from network peer. TEI=0 Sending UA TEI=0 MDL-ERROR (F): SABME in state 7(Multi-frame established) TEI=0 Got SABME from network peer. TEI=0 Sending UA TEI=0 MDL-ERROR (F): SABME in state 7(Multi-frame established) TEI=0 Got SABME from network peer. TEI=0 Sending UA TEI=0 MDL-ERROR (F): SABME in state 7(Multi-frame established) TEI=0 Got SABME from network peer. TEI=0 Sending UA TEI=0 MDL-ERROR (F): SABME in state 7(Multi-frame established) -----Original Message----- From: asterisk-users-boun...@lists.digium.com [mailto:asterisk-users-boun...@lists.digium.com] On Behalf Of jg Sent: Tuesday, February 18, 2014 3:12 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] PRI Error on span 1: Received MDL/TEI management message, but configured for mode other than PTMP MDL/TEI is pretty low level. Which card are you using? chan_dahdi.conf? Card config? PCAP trace? Q.931 and Q.921 messages are relatively easy to debug with wireshark. jg -- _____________________________________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs: http://www.asterisk.org/hello asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users -- _____________________________________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- New to Asterisk? Join us for a live introductory webinar every Thurs: http://www.asterisk.org/hello asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users