I have installed two HFC PCI A-cards running zaphfc from bristuff-0.0.2, which seems to work quite fine, but I continously receive the messages "D-Channel on span 1 up" followed by "D-Channel on span 1 down" with a few seconds interval. Why is that? Bri intense debug log and configuration files below.
I don't need ztdummy or zaprtc, do I? I get some frame slips as well, but zaphfc should be enough to get the timing? Regards, Tobias T203 counter expired, sending RR and scheduling T203 again Sending Receiver Ready (0) > [ 00 d9 01 01 ] > Supervisory frame: > SAPI: 00 C/R: 0 EA: 0 > TEI: 108 EA: 1 > Zero: 0 S: 0 01: 1 [ RR (receive ready) ] > N(R): 000 P/F: 1 > 0 bytes of data -- Restarting T203 counter paulus*CLI> < [ 00 d9 01 01 ] < Supervisory frame: < SAPI: 00 C/R: 0 EA: 0 < TEI: 108 EA: 1 < Zero: 0 S: 0 01: 1 [ RR (receive ready) ] < N(R): 000 P/F: 1 < 0 bytes of data -- ACKing all packets from 0 to (but not including) 0 -- Since there was nothing left, stopping T200 counter -- Stopping T203 counter since we got an ACK -- Nothing left, starting T203 counter -- Got RR response to our frame -- Restarting T203 counter paulus*CLI> paulus*CLI> paulus*CLI> < [ 02 d9 53 ] < Unnumbered frame: < SAPI: 00 C/R: 1 EA: 0 < TEI: 108 EA: 1 < M3: 2 P/F: 1 M2: 0 11: 3 [ DISC (disconnect) ] < 0 bytes of data -- Got Disconnect from peer. Sending Unnumbered Acknowledgement > [ 02 d9 73 ] > Unnumbered frame: > SAPI: 00 C/R: 1 EA: 0 > TEI: 108 EA: 1 > M3: 3 P/F: 1 M2: 0 11: 3 [ UA (unnumbered acknowledgement) ] > 0 bytes of data -- Restarting T203 counter Sending Set Asynchronous Balanced Mode Extended > [ 00 d9 7f ] > Unnumbered frame: > SAPI: 00 C/R: 0 EA: 0 > TEI: 108 EA: 1 > M3: 3 P/F: 1 M2: 3 11: 3 [ SABME (set asynchronous balanced mode extended ) ] > 0 bytes of data == D-Channel on span 1 down paulus*CLI> < [ 00 d9 73 ] < Unnumbered frame: < SAPI: 00 C/R: 0 EA: 0 < TEI: 108 EA: 1 < M3: 3 P/F: 1 M2: 0 11: 3 [ UA (unnumbered acknowledgement) ] < 0 bytes of data -- Got UA from network peer Link up. -- Restarting T203 counter == D-Channel on span 1 up /etc/zaptel.conf: ; By the way, how do I know if I should use CAS or CCS resp. AMI or HDB3? loadzone=nl defaultzone=nl span=1,1,5,ccs,ami bchan=1-2 dchan=3 span=2,0,5,ccs,ami bchan=4-5 dchan=6 /etc/asterisk/zapata.conf: [channels] switchtype = euroisdn ; to/from ISDN PtMP signalling = bri_cpe_ptmp pridialplan=local echocancel=no immediate=no language=se group = 1 context=remote channel => 1-2 ; to/from the PBX signalling = bri_net_ptmp pridialplan=local echocancel=no ;overlapdial=yes immediate=no language=se group = 2 context=analog-ankn channel => 4-5 _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
