Thx for your reply.
On Wed, 2005-03-16 at 17:35, Steve Underwood wrote:
> Hi Vladyslav,
>
> Use 0.0.2pre1, but add the line
> fax.verbose = TRUE;
> just after
> fax_init(&fax, calling_party, NULL);
>
> That will turn on the detailed logging.
>
Added, recompiled and tested again.
> Is the listing you posted the entire log? It looks like there should be
> more.
>
Yes, before there was some additional information
> One common mistake people make - Did you use the "|caller" parameter
> when running txfax?
yes I use that one.
> Regards,
> Steve
>
Here is new one : (but it's spandsp-0.0.2pre10)
*CLI> -- Executing NoOp("SIP/103-dfb6", "") in new stack
-- Executing AGI("SIP/103-dfb6", "set-timestamp.agi") in new stack
-- Executing System("SIP/103-dfb6", "echo "16032005-18:15:06 -
"VladK" <103> - SIP/103-dfb6 - 901" >> /var/log/asterisk/calls") in new
stack
-- Executing DBput("SIP/103-dfb6", "RepeatDial/103=901") in new
stack
-- DBput: family=RepeatDial, key=103, value=901
-- Executing DBget("SIP/103-dfb6", "recv=Record/103") in new stack
-- DBget: varname=recv, family=Record, key=103
-- DBget: set variable recv to on
-- Executing GotoIf("SIP/103-dfb6", "1?7:9") in new stack
-- Goto (from-sip,901,7)
-- Executing SetVar("SIP/103-dfb6",
"CALLFILENAME=20050316-181506-103-901") in new stack
-- Executing Monitor("SIP/103-dfb6", "wav|20050316-181506-103-901")
in new stack
-- Executing Goto("SIP/103-dfb6", "from-sip-post|901|1") in new
stack
-- Goto (from-sip-post,901,1)
-- Executing Answer("SIP/103-dfb6", "") in new stack
-- Executing TxFAX("SIP/103-dfb6", "/tmp/testfax.tif|caller") in new
stack
Slow carrier up
Mar 16 18:15:10 NOTICE[10168]: rtp.c:540 ast_rtp_read: Unknown RTP codec
100 received
Slow carrier down
Slow carrier up
Slow carrier down
Slow carrier up
<<< NSF: 20 00 00 79 00 00 00 82 0f 09 03 10 10 00 02 95 80 9c f8 80 40
01 49 02 41 52 41 59 4f 5a 20 55 4b 52 41 49 4e 45 23 20 03
NSF without final frame tag
The remote was made by 'Panasonic'
<<< DIS: 80 20 ee 99 84 80 11
DIS with final frame tag
In state 10
DIS:
V.8 capable
Prefer 256 octet blocks
Can receive fax
Supported data signalling rates: V.27ter, V.29 and V.17
R8x7.7lines/mm and/or 200x200pels/25.4mm
2D coding
Scan line length: 215mm or 255mm
Recording length: A4 (297mm) and B4 (364mm)
Receiver's minimum scan line time: 5ms at 3.85 l/mm: T7.7 = T3.85
Error correction mode
R8x15.4lines/mm
Metric-based resolution preferred
Minimum scan line time for higher resolutions: T15.4 = T7.7
DCS:
Can receive fax
Selected data signalling rate: V.29, 9600bps
2D coding
Scan line length: 215mm
Recording length: A4 (297mm)
Minimum scan line time: 20ms
Minimum scan line time for higher resolutions: T15.4 = T7.7
Start sending document
Start tx document
Changed from phase 2 to 4
>>> DCS: 83 00 c6 80 80 80 00
HDLC underflow in state 3
Changed from phase 4 to 6
Changed from phase 6 to 3
Slow carrier up
<<< CFR: 84
CFR with final frame tag
In state 4
Trainability test succeeded
Start tx page
Slow carrier down
Changed from phase 3 to 6
*CLI> show ch
channel channels channeltypes
*CLI> show channels
Channel (Context Extension Pri ) State Appl.
Data
0 active channel(s)
_______________________________________________
Asterisk-Users mailing list
Asterisk-Users@lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
