Silence Threshold works nicely, after 10 seconds of silence it will hangup.
This while thread is a great reaon to push users in the 10 to 12 line range to go for a PRI.. Chad -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Sent: October 20, 2006 10:11 AM To: [email protected] Subject: Re: [on-asterisk] Line seizure If you look in the vm_general.inc config file, the default maximum voicemail length is 3 minutes (180 sec.) I thought there was a way to lower this with FreePBX but that must have been another version of *. Anyway, that setting definitely affects the length of time the line is held open if someone gets to voicemail and just hangs up or doesn't press the # when done. This affects the spousal allowance factor also. Any point in playing with the other settings there, such as the silence threshold? Peter M. > I am not sure if my problem falls into this category. I have a linksys SPA3102 on Trixbox 1.2. > If I call in on the PSTN which the SPA3102 is connected to and hangup > during the Trixbox Greeting. It does not detect the hangup / > Disconnect tone and the line stays open but in my case the > disconnected call goes to my voice mail extension which then records > about 3 mins of the fast disconnected tone before the mail box is full (about 3 mins) and then finally disconnects. other times it just stays connect ed for about a minute and a half before disconnecting. > I am not sure if the problem is with either my SPA3102 or the Trixbox > but one of them is not detecting this tone. > If I enable Detect PSTN Long Silence on the SPA3102 then I get > disconnect when I get placed on hold by anyone without some kind of > hold music or beeps. I have played around with the duration of the > silence but it ends up defeating the cause as i have to set it to a high number to be effective. Does anyone have a solutions to this problem? > > On 10/19/06, Henry.L.Coleman <[EMAIL PROTECTED]> wrote: > I have the same problem on a FX line while the other 3 normal lines are fine > I have tried everything. The only way we are ever going to solve this > problem is to detect the off-hook warning tone. > Here is the spec for N/America : > 1400 Hz, 2060 Hz, 2450 Hz, and 2600 Hz, at a cadence of 0.1s on, 0.1s off. > If anyone can code * to hang up a zap channel on this tone I would be most > grateful (and so would a lot of other people) > (This is definately a three beer bounty) > > Henry L.Coleman CEO . > > *VoIP-PBX* 1-866-415-5355 > Toronto Ontario > Canada > > > >>>> On Thu, Oct 19, 2006 at2:57 PM, in message > > <[EMAIL PROTECTED]>, > > <[EMAIL PROTECTED]> wrote: > >> Interesting, thanks.That's more than our Aliant rep was able to > > tell us. > >> He thinks that supervised disconnect is not available on home phone > > lines.He > >> does think it available on business lines though.I'll have to go to > > > >> someone's hous e where there's high speed and give this a shot again. > > > > I also have this problem with my Asterisk setup (occasional failure to > > hang up the line). I blamed it on the crappy Zaptel clone card I have, > > but it sounds like it might be due to another reason. > > > > How can I forcibly hangup the channel from within the CLI? > > > > - Julian > > > > > > -- > > -- Julian C. Dunn, P.Eng.<[EMAIL PROTECTED] > > > -- Platform Administrator * CBC.ca Production &Operations > > -- Office: 2C310-J*Tel.: (416) 205-3311 x6988 > > > >--------------------------------------------------------------------- > > To unsubscribe, e-mail: [EMAIL PROTECTED] > > For additional commands, e-mail: [EMAIL PROTECTED] > > > > > > > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [EMAIL PROTECTED] > For additional commands, e-mail: [EMAIL PROTECTED] > > > ******************************************************** Peter MacFarlane, ACP Network Administration & Programming Target Call Center/ Message Centre P.E.I. ******************************************************** --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]
