Johannes,
It seems like commit db3bdcb9c3ff ("mac80211: allow AP_VLAN operation on
crypto controlled devices") has broken 4-addr operation on crypto
controlled devices as reported by sebastian.
The commit was mainly focused in addressing the problem in supporting
VLANs on crypto controlled devices but since 4-addr mode is also
dependent on AP_VLAN interface, this commit breaks the 4-addr AP mode.
I have couple of ideas on how to address the problem,
1) Add a new hw_flag and based on the hardware flag, allow/disallow the
creation of AP_VLAN interface.
diff --git a/include/net/mac80211.h b/include/net/mac80211.h
index d2279b2..301d9c38 100644
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -2084,6 +2084,11 @@ struct ieee80211_txq {
* @IEEE80211_HW_DOESNT_SUPPORT_QOS_NDP: The driver (or firmware)
doesn't
* support QoS NDP for AP probing - that's most likely a driver
bug.
*
+ * @IEEE80211_HW_SUPPORTS_SW_ENCRYPT: Device is capable of transmitting
+ * frames encrypted in software, only valid when SW_CRYPTO_CONTROL
+ * is enabled. Based on this flag, mac80211 can allow/disallow VLAN
+ * operations in the BSS.
+ *
* @NUM_IEEE80211_HW_FLAGS: number of hardware flags, used for sizing
arrays
*/
enum ieee80211_hw_flags {
@@ -2129,6 +2134,7 @@ enum ieee80211_hw_flags {
IEEE80211_HW_SUPPORTS_TDLS_BUFFER_STA,
IEEE80211_HW_DEAUTH_NEED_MGD_TX_PREP,
IEEE80211_HW_DOESNT_SUPPORT_QOS_NDP,
+ IEEE80211_HW_SUPPORTS_SW_ENCRYPT,
/* keep last, obviously */
NUM_IEEE80211_HW_FLAGS
diff --git a/net/mac80211/iface.c b/net/mac80211/iface.c
index 555e389..c825d27 100644
--- a/net/mac80211/iface.c
+++ b/net/mac80211/iface.c
@@ -1736,6 +1736,11 @@ int ieee80211_if_add(struct ieee80211_local
*local, const char *name,
ASSERT_RTNL();
+ if ((type == NL80211_IFTYPE_AP_VLAN) && !params->use_4addr &&
+ ieee80211_hw_check(local->hw, SW_CRYPTO_CONTROL) &&
+ !ieee80211_hw_check(local->hw, SUPPORTS_SW_ENCRYPT))
+ return -EOPNOTSUPP;
+
if (type == NL80211_IFTYPE_P2P_DEVICE || type ==
NL80211_IFTYPE_NAN) {
struct wireless_dev *wdev;
2) Allow mac80211 to call set_key for GTKs on AP_VLAN interfaces for
crypto controlled devices, let the driver decide whether to return '1'
or some error code based on their support for transmitting sw encrypted
frames. I am little skeptical with this approach as drivers are totally
unaware of AP_VLAN interfaces.
diff --git a/net/mac80211/key.c b/net/mac80211/key.c
index ee0d0cc..0ff5597 100644
--- a/net/mac80211/key.c
+++ b/net/mac80211/key.c
@@ -167,7 +167,8 @@ static int ieee80211_key_enable_hw_accel(struct
ieee80211_key *key)
* The driver doesn't know anything about VLAN
interfaces.
* Hence, don't send GTKs for VLAN interfaces to the
driver.
*/
- if (!(key->conf.flags & IEEE80211_KEY_FLAG_PAIRWISE))
+ if ((!(key->conf.flags & IEEE80211_KEY_FLAG_PAIRWISE) &&
+ !ieee80211_hw_check(&key->local->hw,
SW_CRYPTO_CONTROL)))
goto out_unsupported;
}
Please let me know which is the better way to deal the problem.
Thanks,
Manikanta
On 2018-04-24 14:39, Sebastian Gottschall wrote:
consider my comment regarding vlan_ap.
this patch will break wds ap / wds sta support with latest mac80211
(see also my post on the wireless mailing list about the breaking
patch in mac80211)
so AP_VLAN must be masked always for all chipsets. otherwise wds
breaks and this is not just a guess. i tested it yesterday using this
patch and found
the cause of the issue
the following lines
+ if (test_bit(WMI_SERVICE_PER_PACKET_SW_ENCRYPT,
ar->wmi.svc_map)) {
+ ar->hw->wiphy->interface_modes |= BIT(NL80211_IFTYPE_AP_VLAN);
+ ar->hw->wiphy->software_iftypes |=
BIT(NL80211_IFTYPE_AP_VLAN);
+ }
must be just
+ ar->hw->wiphy->interface_modes |= BIT(NL80211_IFTYPE_AP_VLAN);
+ ar->hw->wiphy->software_iftypes |=
BIT(NL80211_IFTYPE_AP_VLAN);
everthing else will cause a regression
Am 24.04.2018 um 10:09 schrieb Kalle Valo:
Manikanta Pubbisetty <mpubb...@codeaurora.org> writes:
Mutlicast/broadcast traffic destined for a particular vlan group will
always be encrypted in software. To enable dynamic VLANs, it requires
driver support for sending software encrypted packets.
In ath10k, sending sw encrypted frames is allowed only when we insmod
the driver with cryptmode param set to 1, this configuration disables
hardware crypto and enables RAW mode implicitly. Since, enabling raw
mode has performance impact, this cannot be considered as an ideal
solution for supporting VLANs in the driver.
As an alternative take, in this approach, cryptographic keys for
unicast traffic(per peer PTKs) and keys for non-vlan group traffic
will be configured in hardware, allowing hardware encryption for
unicast
and non-vlan group traffic. Only vlan group traffic will be encrypted
in
software and pushed to the target with encap mode set to RAW in the
TX
descriptors.
Not all firmwares can support this type of key configuration(having
few
keys installed in hardware and few only in software); for this
purpose a
new WMI service flag "WMI_SERVICE_PER_PACKET_SW_ENCRYPT" is
introduced to
advertise this support.
Also, adding the logic required to send sw encrypted frames in raw
mode.
Tested this change on QCA9984(firmware version 10.4-3.5.3-00057).
Signed-off-by: Manikanta Pubbisetty <mpubb...@codeaurora.org>
Your name in patchwork is wrong and hence my script uses the wrong
name. Please fix it by registering to patchwork[1] where it's possible
to change your name during registration, but only one time. If that
doesn't work then send a request to helpd...@kernel.org and the admins
can fix it.
[1] https://patchwork.kernel.org/register/
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k