Hi, No one has an idea?
I just tried the whole thing with the latest 2.6-git using kernel 2.6.24 and also the ath5k in kernel 2.6.25-rc1. Exactly the same behavior. Greetings, M. Kramer Morten Kramer wrote: > Hello, > > > I just compiled kernel 2.6.24-mm1. Can't get ath5k to work properly. > > Worked fine under kernel 2.6.24 with the latest madwifi-snapshot. > > Using the following card: > > -==Device Information==- > MAC Version: 5212 (0x50) > MAC Revision: 5213A (0x59) > PHY Revision: 5110 (0x00) > PHY Revision: 5110 (0x00) > -==EEPROM Information==- > EEPROM Version: 4.8 > EEPROM Size: 16K > Regulatory Domain: 0x64 > -==== Capabilities ====- > | 802.11a Support: no | > | 802.11b Support: yes | > | 802.11g Support: yes | > | RFKill Support: yes | > | 32KHz Crystal: yes | > ======================== > GPIO registers: CR 00000000 DO 00000000 DI 00000007 > > dmesg output: > ath5k_pci 0000:02:02.0: registered as 'phy0' > phy0: Selected rate control algorithm 'pid' > ath5k phy0: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43) > ath5k phy0: RF2112A 2GHz radio found (0x46) > iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10 (17-Aug-2007) > wlan0 renamed to ath0 > udev: renamed network interface wlan0 to ath0 > > > I can associate to networks: > > ath0 IEEE 802.11g ESSID:"92" > Mode:Managed Frequency:2.447 GHz Access Point: > 00:1B:2F:7A:AB:A6 > Bit Rate=54 Mb/s Tx-Power=27 dBm > Retry min limit:7 RTS thr:off Fragment thr=2352 B > Encryption key:off > Link Quality=106/100 Signal level=-25 dBm Noise level=-93 dBm > Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 > Tx excessive retries:0 Invalid misc:0 Missed beacon:0 > > dmesg output: > ath0: Initial auth_alg=0 > ath0: authenticate with AP 00:1b:2f:7a:ab:a6 > ath0: RX authentication from 00:1b:2f:7a:ab:a6 (alg=0 transaction=2 > status=0) > ath0: authenticated > ath0: associate with AP 00:1b:2f:7a:ab:a6 > ath0: RX AssocResp from 00:1b:2f:7a:ab:a6 (capab=0x411 status=0 aid=1) > ath0: associated > ath0: CTS protection enabled (BSSID=00:1b:2f:7a:ab:a6) > ath0: switched to long barker preamble (BSSID=00:1b:2f:7a:ab:a6) > > > > But that's basically what i can do. I can't ping anything, don't get any > response to DHCP-requests/discovers. Can't reach the default Gateway of > the Netgear wireless-router (essid 92). The same setup works great with > kernel 2.6.24 and the latest madwifi-snapshot. > > I don't see any errors in dmesg, 'ping' doesn't output any errors, there > are just no replies. If i scan the whole network range with nmap, nmap > finishes very quick and states all hosts (except the local) as down. I > ran a wireshark session and saw some Samba-broadcasts, but can't ping > or scan the source IP. > > Any suggestions? > > > > > Greetings, > M. Kramer > > _______________________________________________ > ath5k-devel mailing list > [email protected] > https://lists.ath5k.org/mailman/listinfo/ath5k-devel > _______________________________________________ ath5k-devel mailing list [email protected] https://lists.ath5k.org/mailman/listinfo/ath5k-devel
