> From: "Hugh Davenport" <h...@davenport.net.nz>
> To: linvi...@tuxdriver.com
> Cc: ath5k-devel@lists.ath5k.org, linux-wirel...@vger.kernel.org, 
> lrodrig...@atheros.com, m...@bobcopeland.com,
> mickfl...@gmail.com, jirisl...@gmail.com
> Sent: Tuesday, February 1, 2011 2:41:42 AM
> Subject: ath5k: issues with AHB support on ubiquiti bullet 2 (AR2315)
> Hey all,
> 
> I'm just letting you know that I have been having issues getting the
> the
> AHB support with the ath5k driver working (from compat-wireless
> 2011-01-05).
> 
> I'm testing it on an ubiquiti bullet 2 device which internally is a
> AR2315 WiSoC. I am using openwrt backfire with the mac80211 package
> patched to use a later version of compat-wireless (ie one with AHB
> support in ath5k). I had to modify some of the patches in openwrt so
> they applied cleanly, but don't think any affected the ath5k (and
> would
> cause the problem i have).
> 
> Basically the issue is this. When I try to load the module as is in
> the
> source tree, the system hangs and module never loads (device restarts
> itself).
> 
> I tried a bit of debugging (sorry about any newbie techniques here, im
> new to kernel debugging) by just printing and returning errors after
> every main function called. The problem seemed to be with the first
> time
> it called ath5k_hw_reg_write, which from my tracing seemed to be in th
> wisoc reset function in the following chain.
> 
> ath5k_hw_reg_write (ath5k.h)
> ath5k_hw_wisoc_reset (reset.c)
> ath5k_hw_nic_wakeup (reset.c)
> ath5k_hw_init (attach.c)
> ath5k_init_softc (base.c)
> ath_ahb_probe (ahb.c)
> 
> 
> I then tried out a few things in the vain attempt to get it to load
> the
> module, one which seemed to work is taking out the ioremap_nocache
> call
> in ath_ahb_probe, and set mem to be res->start (on my system this is
> 0xb0000000 (the same as what madwifi tells me as well)). With this
> /fix/
> the module now loads, gives the output below, but i can't bring the
> interface up (device crashes again).
> 
> Atheros AR2315 chip found (MAC: 0x87, PHY: 0x48)
> 
> 
> continuing traces when bring interface up brings me to another
> ath5k_hw_reg_write call in the following chain
> 
> ath5k_hw_reg_write (ath5k.h)
> ath5k_hw_start_rx_dma (dma.c)
> ath5k_rx_start (base.c)
> ath5k_reset (base.c)
> ath5k_init_hw (base.c)
> ath5k_start (mac80211-ops.c)
> 
I have just ran latest openwrt trunk and it works ok with default settings
on my JJPlus 25APN (Atheros AP48 reference design) with AR2313. You chipset
is a bit different and I don't have any access to it so I cannot really
test.

I have posted already some extra patches to try but maybe you could try
them again. I have just added extra reset I have found in documentation
and shamelessly copied some code from madwifi. From what I have noticed 
the chip will hang as in your description on any access to MAC registers
if it's not resetted properly.

So here is the mentioned and untested patch:

[PATCH] Added extra wakeup form sleep in PCI for AR2315 and up

Signed-off-by: Wojciech Dubowik <wojciech.dubo...@neratec.com>
---
 drivers/net/wireless/ath/ath5k/ahb.c   |   18 ++++++++++++++++++
 drivers/net/wireless/ath/ath5k/reg.h   |    9 +++++++++
 drivers/net/wireless/ath/ath5k/reset.c |    1 +
 3 files changed, 28 insertions(+), 0 deletions(-)

diff --git a/drivers/net/wireless/ath/ath5k/ahb.c 
b/drivers/net/wireless/ath/ath5k/ahb.c
index 707cde1..3a665ba 100644
--- a/drivers/net/wireless/ath/ath5k/ahb.c
+++ b/drivers/net/wireless/ath/ath5k/ahb.c
@@ -132,6 +132,24 @@ static int ath_ahb_probe(struct platform_device *pdev)
                reg = __raw_readl((void __iomem *) AR5K_AR2315_BYTESWAP);
                reg |= AR5K_AR2315_BYTESWAP_WMAC;
                __raw_writel(reg, (void __iomem *) AR5K_AR2315_BYTESWAP);
+
+               /* wake up the MAC */
+               /* NOTE: for the following write to succeed the
+                * RST_AHB_ARB_CTL should be set to 0. This driver
+                * assumes that the register has been set to 0 by boot loader
+                */
+               reg = __raw_readl((void __iomem *) AR5K_AR2315_PCI_MAC_SCR);
+               reg = (reg & ~AR5K_AR2315_PCI_MAC_SCR_SLMODE_M) |
+                       (AR5K_AR2315_PCI_MAC_SCR_SLM_FWAKE
+                        << AR5K_AR2315_PCI_MAC_SCR_SLMODE_S);
+               __raw_writel(reg, (void __iomem *) AR5K_AR2315_PCI_MAC_SCR);
+
+               /* wait for the MAC to wakeup */
+               while
+               (
+                       __raw_readl((void __iomem *) AR5K_AR2315_PCI_MCFG)
+                                       & AR5K_PCICFG_SPWR_DN
+               );
        } else {
                /* Enable WMAC DMA access (assuming 5312 or 231x*/
                /* TODO: check other platforms */
diff --git a/drivers/net/wireless/ath/ath5k/reg.h 
b/drivers/net/wireless/ath/ath5k/reg.h
index 7ad05d4..7763e15 100644
--- a/drivers/net/wireless/ath/ath5k/reg.h
+++ b/drivers/net/wireless/ath/ath5k/reg.h
@@ -2587,3 +2587,12 @@
 
 #define AR5K_AR2315_BYTESWAP   0xb100000c
 #define AR5K_AR2315_BYTESWAP_WMAC      0x00000002
+
+#define AR5K_AR2315_PCI                                0xb0100000
+#define AR5K_AR2315_PCI_MAC_SCR        (AR5K_AR2315_PCI + 0x4004)
+#define AR5K_AR2315_PCI_MAC_SCR_SLMODE_M       0x00030000
+#define AR5K_AR2315_PCI_MAC_SCR_SLMODE_S       16
+#define AR5K_AR2315_PCI_MAC_SCR_SLM_FWAKE      0
+
+#define AR5K_AR2315_PCI_MCFG   (AR5K_AR2315_PCI + 0x4010)
+#define AR5K_AR2315_PCI_MCFG_SPWR_DN   0x00010000
diff --git a/drivers/net/wireless/ath/ath5k/reset.c 
b/drivers/net/wireless/ath/ath5k/reset.c
index 8420689..35e6d2d 100644
--- a/drivers/net/wireless/ath/ath5k/reset.c
+++ b/drivers/net/wireless/ath/ath5k/reset.c
@@ -405,6 +405,7 @@ static int ath5k_hw_wisoc_reset(struct ath5k_hw *ah, u32 
flags)
        udelay(100);
 
        /* Bring BB/MAC out of reset */
+       regval = __raw_readl(reg);
        __raw_writel(regval & ~val, reg);
        regval = __raw_readl(reg);
 
-- 
1.7.1


Tell me if it helps.

Wojtek

> 
> I am sorry about the long email, but I thought the more info you guys
> have, the better.
> 
> If you have any ideas I can try, any more testing you may need me to
> do,
> or anything that could help me get it working, let me know, and i'll
> do
> my best to get anything done asap.
> 
> Cheers,
> 
> Hugh Davenport
> --
> To unsubscribe from this list: send the line "unsubscribe
> linux-wireless" in
> the body of a message to majord...@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
_______________________________________________
ath5k-devel mailing list
ath5k-devel@lists.ath5k.org
https://lists.ath5k.org/mailman/listinfo/ath5k-devel

Reply via email to