On Sunday 30 March 2008 16:42:23 Tom Ivar Helbekkmo wrote:
> Kern Sibbald <[EMAIL PROTECTED]> writes:
> > I suspect that has something to do with the fact that you are using
> > spooling, and they record the start block early in the game at the
> > beginning of the spooling and the code is not intelligent enough to
> > wait until the very first block is actually written to *tape*.
>
> That is correct. In stored/append.c, in do_append_data(), there are two
> calls to write_session_label(), performed at the start and end of
> spooling to a disk file. These calls, which generate session labels in
> the disk file, marking the start and end of the session, both cause
> information about the current tape position to be recorded in the job's
> dcr structure.
>
> This has two specific consequences:
>
> - If several jobs start spooling at the same time, they will all get the
> current tape position noted as the StartFile/StartBlock for the job.
> If they end up despooling to the file that was current when they
> started spooling, this is what will end up in the JOBMEDIA table. If
> there is a file change before they despool, the setting of NewFile in
> the dcr structure will fix this up later, but the "start of session"
> label is already in the spool file, of course, so it holds the wrong
> information anyway.
>
> - If the job is longer than the maximum spool size, it will get its
> first spool session despooled, and then start spooling again after the
> first despooling is over. The last blocks despooled to tape from the
> first session will not have been recorded, but they will be flushed
> later, when the next session despools. However, if another job has
> been despooling while this one is spooling its second round, the
> session label written to the spool file at its close will cause the
> EndFile/Endblock to be set to wherever the tape is at that time. When
> the dangling record is flushed to JOBMEDIA, it gets this wrong
> information. Both session labels in the spool file will be wrong,
> too, of course, because they reflect the state of the tape during
> spooling, not during despooling.
>
> I would have to study the code much more closely to work out what's the
> proper fix -- but it seems clear that it should involve creating the
> session labels only when something is actually written to the archive
> device, not during spooling. I'm tempted to try making do_append_data()
> not create session labels if we're spooling, and add the making of them
> to despool_data() in stored/spool.c. Sound reasonable?
Nice analysis. I'm impressed.
Yes, your suggestion sounds reasonable, but I hesitate to move such calls
around due to possible side effects, so prefer for the moment a "minimal"
fix. Perhaps moving the calls is something to do more long term.
I have made a simple patch, which seems to correct the problem.
Index: src/stored/spool.c
===================================================================
--- src/stored/spool.c (revision 6701)
+++ src/stored/spool.c (working copy)
@@ -246,6 +246,13 @@
dcr->dblock(BST_DESPOOLING);
dcr->despool_wait = false;
dcr->despooling = true;
+ /*
+ * If we have not switched volumes, update the start location when
+ * we begin despooling.
+ */
+ if (!dcr->NewVol) {
+ set_start_vol_position(dcr);
+ }
/*
* This is really quite kludgy and should be fixed some time.
It is committed to the trunk, but I am doing a bit more testing on the 2.2.9
branch before applying it. I would appreciate to know if it fixes your
problem.
Best regards,
Kern
>
> -tih
-------------------------------------------------------------------------
Check out the new SourceForge.net Marketplace.
It's the best place to buy or sell services for
just about anything Open Source.
http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace
_______________________________________________
Bacula-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bacula-devel
