Hello Robert, Bacularis is quite handy. :)
When you have an opportunity, you may find Bill's bacula backup report script useful as well. When I implemented it (approximately 1-1.5 years ago), I did find that it doesn't handle SSL communication, so you'd probably need to set up postfix or a similar local mail service, then point the script at that infrastructure. I reviewed the headers for your first email. You sent it around the time you stated, it was received by one of your mail carrier's servers, then held for 4 hours before being dispatched and rapidly relayed to the list. Not sure how you access headers in your email client, but once you get the full message do a ctrl+f for ' Nov' and/or 'Received:' *Received*: from SJ5PPFF2528D033.namprd15.prod.outlook.com (2603:10b6:a0f:fc02::b17) *by SJ0PR15MB4759.namprd15.prod.outlook.com <http://SJ0PR15MB4759.namprd15.prod.outlook.com>* (2603:10b6:a03:37c::23) with Microsoft SMTP Server (version=TLS1_2, cipher=TLS_ECDHE_RSA_WITH_AES_256_GCM_SHA384) id 15.21.615.8; *Tue, 10 Nov 2026 16:53:44 +0000* *Received: from mail-northcentralusazon11022119.outbound.protection.outlook.com <http://mail-northcentralusazon11022119.outbound.protection.outlook.com>* ([40.107.200.119] helo=CH5PR02CU005.outbound.protection.outlook.com) *by sfi-mx-1.v28.lw.sourceforge.com <http://sfi-mx-1.v28.lw.sourceforge.com>* with esmtps (TLS1.2:ECDHE-RSA-AES256-GCM-SHA384:256) (Exim 4.100.1) id 1xQvHC-000000004EP-38hW for [email protected]; *Tue, 10 Nov 2026 23:29:19 +0000* Your most recent email's headers insist that you sent it at 13:31 UTC, with a less than 1 minute transit time to the mailing list servers. Are you certain you send your most recent email at 12:21 UTC? I checked the headers for your email to the list back in April 2026, and I see a similar delay. The intial email was delayed transiting from the outlook outbound to the sourceforge server by about 3 hours. In your subsequent reply to bill (which for me, was to the list and not directly to my address), I saw a delay of 1.5 hours, again between the outbound outlook server to the sourceforge server. I would generally suspect that this is due to something on the outlook side, but I cannot be certain. For example there might be a mechanism whereby the sourceforge server refuses to accept a promptly submitted email because it is overloaded, but later accepts the same email when the sending server retries. I'm fairly confident something between you and the list ate Bill's first email, likely because of the script. If you would like to troubleshoot this further I am open to an off-list email exchange. In particular, I'd like to send you a few dummy script files just to see which emails you do and don't get. Feel free to email me directly offlist if you would like to do that. This email is being sent at 20:27 UTC (Wednesday Nov 11th). Regards, Robert Gerber 402-237-8692 [email protected] On Wed, Nov 11, 2026 at 7:31 AM Robert Webb <[email protected]> wrote: > Rob, > > Thanks for the feedback and attaching the script. Once this big restore > eventually finishes, I will certainly run Bill's tape test and in the > tapealert script. I looked this morning in my spam filtering from yesterday > and do not see the first email as being even received. > > Still trying to get up to speed with Bacula, but am using bacularis as my > front end right now. > > My first email was sent at 16:53 UTC yesterday and I didn't get a > delivered copy until 23:30 UTC. Received Bill's second email at 00:02 UTC. > > Sending this at 12:31 UTC November 11th. > > Robert > ------------------------------ > *From:* Rob Gerber <[email protected]> > *Sent:* Tuesday, November 10, 2026 11:13 PM > *To:* Robert Webb <[email protected]> > *Cc:* Bill Arlofski <[email protected]>; > [email protected] <[email protected]> > *Subject:* Re: [Bacula-users] LTO9 Drive Recommended Block Sizes > > Robert, > > Bill attached his tape test script to his first email. Perhaps your email > service blocked the email because it contained a script. I have renamed the > script to not end in .sh, packed it in a password protected zip (password: > bacula), and have re-attached it here. Please let me know if you receive it. > > Regarding the tapealert script, it provides essential information about > errors reported by the tape drive. Things like "need cleaning' or 'tape > broken!'. Because you do not have a changer (which can monitor and report > some of those things), I think you especially could benefit from this > upgraded script. > > I agree, mtx-changer probably isn't useful to you. > > When you reply via email, please state the time in UTC. I will let you > know what the received time is on my end. A reply-all should take the > mailing list out of the equation, since you'll also be directly replying to > me. Maybe you are having email server difficulties. As you may already > know, we can also check the mailing list website for delivery status of an > email, though I'm not sure how quickly those emails are displayed. > > Incidentally, I received your first email from the list at 23:30 UTC. > > Regards, > Robert Gerber > 402-237-8692 <(402)%20237-8692> > [email protected] > > > On Tue, Nov 10, 2026 at 8:52 PM Robert Webb <[email protected]> wrote: > > Hi Bill, > > Thanks for the pointer to your scripts. However, not sure which ones might > be applicable as I am using a single drive setup and no changer. > > Also, I never received your first email and it took hours for mine to > actually come through. > > Robert > > Get Outlook for Android <https://aka.ms/AAb9ysg> > ------------------------------ > *From:* Bill Arlofski via Bacula-users <[email protected] > > > *Sent:* Tuesday, 10 November 2026 19:01:27 > *To:* [email protected] < > [email protected]> > *Subject:* Re: [Bacula-users] LTO9 Drive Recommended Block Sizes > > Hello Robert, > > Sorry for the two rapid replies, but in addition to my last email, I > thought I might point you to two "drop-in" replacement > scripts I have written that have some better logging and additional > features as compared to the originals shipped with Bacula > for 20+ years. > > You might want to have a look at `mtx-changer-python.py` and > `bacula-tapealert.py`, available in my Github account here: > > https://github.com/waa > > Hope this helps! > > I look forward to news about your tape drive + Bacula experiences! :) > > > Bill > > -- > Bill Arlofski > [email protected] > _______________________________________________ > Bacula-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/bacula-users > >
_______________________________________________ Bacula-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/bacula-users
