On Wed, Feb 10, 2016 at 11:07:37AM +0100, Robert Schwebel wrote: > Add the following improvements: > > - clarify commands vs. filesystems for network file transport protocols > - Beautify links with prosa text instead of standard headlines > - adapt 'devinfo eth0' parameter output to current code > - improve console texts > - add docs for netconsole.active > > Signed-off-by: Robert Schwebel <r.schwe...@pengutronix.de> > --- > Documentation/user/networking.rst | 44 > ++++++++++++++++++++++++--------------- > 1 file changed, 27 insertions(+), 17 deletions(-) > > diff --git a/Documentation/user/networking.rst > b/Documentation/user/networking.rst > index 6eeb93d..c1b1857 100644 > --- a/Documentation/user/networking.rst > +++ b/Documentation/user/networking.rst > @@ -1,26 +1,25 @@ > Networking > ========== > > -barebox has IPv4 networking support. Several protocols such as > -:ref:`command_dhcp`, :ref:`filesystems_nfs`, :ref:`command_tftp` are > -supported. > +barebox has IPv4 networking support. Several protocols such as :ref:`DHCP > +<command_dhcp>`, NFS and TFTP are supported. > > Network configuration > --------------------- > > The first step for networking is configuring the network device. The network > device is usually ``eth0``. The current configuration can be viewed with the > -:ref:`command_devinfo` command: > +:ref:`devinfo <command_devinfo>` command: > > .. code-block:: sh > > barebox:/ devinfo eth0 > Parameters: > - ipaddr: 192.168.23.197 > - serverip: 192.168.23.1 > + ethaddr: 00:1c:49:01:03:4b > gateway: 192.168.23.1 > + ipaddr: 192.168.23.197 > netmask: 255.255.0.0 > - ethaddr: 00:1c:49:01:03:4b > + serverip: 192.168.23.1 > > The configuration can be changed on the command line with: > > @@ -28,19 +27,21 @@ The configuration can be changed on the command line with: > > eth0.ipaddr=172.0.0.10 > > -The :ref:`command_dhcp` command will change the settings based on the answer > +The :ref:`dhcp command <command_dhcp>` will change the settings based on the > answer > from the DHCP server. > > This low-level configuration of the network interface is often not > necessary. Normally > the network settings should be edited in ``/env/network/eth0``, then the > network interface > -can be brought up using the :ref:`command_ifup` command. > +can be brought up using the :ref:`ifup command <command_ifup>`. > > Network filesystems > ------------------- > > -barebox supports NFS and TFTP as filesystem implementations. See > :ref:`filesystems_nfs` > -and :ref:`filesystems_tftp` for more information. After the network device > has been > -brought up a network filesystem can be mounted with: > +barebox supports NFS and TFTP both with commands (:ref:`nfs <command_nfs>` > and > +:ref:`tftp <command_tftp>`) and as filesystem implementations; see > +:ref:`filesystems_nfs` and :ref:`filesystems_tftp` for more information. > After > +the network device has been brought up, a network filesystem can be mounted > +with: > > .. code-block:: sh > > @@ -52,8 +53,9 @@ or > > mount -t nfs 192.168.2.1:/export none /mnt > > -**NOTE:** this can often be hidden behind the :ref:`command_automount` > command to make > -mounting transparent to the user. > +**NOTE:** The execution of the mount command can often be hidden behind the > +:ref:`automount command <command_automount>`, to make mounting transparent to > +the user. > > Network console > --------------- > @@ -71,11 +73,19 @@ risks. It can be enabled using: > netconsole.ip=192.168.23.2 > netconsole.active=ioe > > -This will send UDP packets to 192.168.23.2 on port 6666. On 192.168.23.2 the > -scripts/netconsole script can be used to control barebox: > +This will send UDP packets to a PC with IP address 192.168.23.2 and port > 6666. > + > +The ``netconsole.active`` parameter consists of the fields "input" (i), > +"output" (o) and "error" (e); if the fields are set, the respective channel > is > +activated on the network console. > + > +On the PC side, the ``scripts/netconsole`` script can be used to remote > control > +barebox: > > .. code-block:: sh > > scripts/netconsole <board IP> 6666 > > -The netconsole can be used just like any other console. > +The netconsole can be used just like any other console. Note, however, that > the > +simple console protocol is is UDP based, so there is no guarantee about > packet ^^^^^
Regards, Steffen Trumtrar -- Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox