Some values differ between LS1046a and LS1021. Move them directly where
needed so that we can drop the #ifdef SOC_TYPE from immap_lsch2.h
Signed-off-by: Sascha Hauer <s.ha...@pengutronix.de>
---
arch/arm/mach-layerscape/lowlevel-ls102xa.c | 5 +++++
include/soc/fsl/immap_lsch2.h | 6 ------
2 files changed, 5 insertions(+), 6 deletions(-)
diff --git a/arch/arm/mach-layerscape/lowlevel-ls102xa.c
b/arch/arm/mach-layerscape/lowlevel-ls102xa.c
index 259d8866d5..7ea0a5b071 100644
--- a/arch/arm/mach-layerscape/lowlevel-ls102xa.c
+++ b/arch/arm/mach-layerscape/lowlevel-ls102xa.c
@@ -299,6 +299,11 @@ static void fsl_epu_clean(void *epu_base)
out_be32(epu_base + offset, 0);
}
+#define TIMER_COMP_VAL 0xffffffffffffffffull
+#define ARCH_TIMER_CTRL_ENABLE (1 << 0)
+#define SYS_COUNTER_CTRL_ENABLE (1 << 24)
+#define SCFG_QSPI_CLKSEL 0x50100000
+
/* ls102xa_init_lowlevel
* Based on ls1046 and U-boot ls102xa arch_cpu_init
*/
diff --git a/include/soc/fsl/immap_lsch2.h b/include/soc/fsl/immap_lsch2.h
index 62e48ae746..ce840d4223 100644
--- a/include/soc/fsl/immap_lsch2.h
+++ b/include/soc/fsl/immap_lsch2.h
@@ -63,10 +63,6 @@
#define LSCH2_QDMA_BASE_ADDR (LSCH2_IMMR + 0x07380000)
#define LSCH2_EHCI_USB1_ADDR (LSCH2_IMMR + 0x07600000)
-#define TIMER_COMP_VAL 0xffffffffffffffffull
-#define ARCH_TIMER_CTRL_ENABLE (1 << 0)
-#define SYS_COUNTER_CTRL_ENABLE (1 << 24)
-
struct ccsr_gur {
u32 porsr1; /* POR status 1 */
#define FSL_CHASSIS2_CCSR_PORSR1_RCW_MASK 0xFF800000
@@ -306,13 +302,11 @@ struct ls102xa_ccsr_gur {
#define SCFG_USB_PHY3 0x08510000
#define SCFG_USB_PHY_RX_OVRD_IN_HI 0x200c
#if defined CONFIG_ARCH_LS1046
-#define SCFG_QSPI_CLKSEL 0x40100000
#define USB_PHY_RX_EQ_VAL_1 0x0000
#define USB_PHY_RX_EQ_VAL_2 0x0080
#define USB_PHY_RX_EQ_VAL_3 0x0380
#define USB_PHY_RX_EQ_VAL_4 0x0b80
#elif defined CONFIG_ARCH_LS1021
-#define SCFG_QSPI_CLKSEL 0x50100000
#define USB_PHY_RX_EQ_VAL_1 0x0000
#define USB_PHY_RX_EQ_VAL_2 0x8000
#define USB_PHY_RX_EQ_VAL_3 0x8004
--
2.39.2
