On Tue, 17 Feb 2009 19:57:47 -0600, Andy Herkey wrote:
> Shannon McMackin wrote:
>> On Tue, 17 Feb 2009 12:38:43 -0600, Andy Herkey wrote:
>>
>>
>>> Shannon McMackin wrote:
>>>
>>>> On Wed, 11 Feb 2009 22:06:35 -0600, Andy Herkey wrote:
>>>>
>>>>
>>>>
>>>>> Shannon McMackin wrote:
>>>>>
>>>>>
>>>>>> 1st, Andy, I apologize for not getting back to you on FC10. I've
>>>>>> had to switch back to Ubuntu.
>>>>>>
>>>>>> We had it working on Intrepid. I don't know for the life of me
>>>>>> what changed. I'm using the libs from try3 that you sent me and
>>>>>> here's the output in the attached file.
>>>>>>
>>>>>>
>>>>>>
>>>>> Shannon,
>>>>> I don't see anything obvious in the output except your provider did
>>>>> not respond to the request for an IP/DNS addresses properly. Line
>>>>> 12 should have looked like this from your provider:
>>>>> rcvd [IPCP ConfNak id=0x1 <addr 10.67.241.190> <ms-dns1
>>>>> 172.16.145.103> <ms-dns2 172.16.145.103>] instead it looks like
>>>>> this:
>>>>> rcvd [IPCP ConfNak id=0x1 <ms-dns1 0.0.0.0> <ms-dns2 0.0.0.0>]
>>>>> So pppd kept sending requests for a local IP address and DNS servers
>>>>> until it gave up.
>>>>>
>>>>> 1 Connect: ppp0 <--> /dev/pts/1
>>>>> 2 sent [LCP ConfReq id=0x1 <asyncmap 0x0>] 3 rcvd [LCP ConfReq
>>>>> id=0x0 <asyncmap 0x0> <auth pap>] 4 sent [LCP ConfAck id=0x0
>>>>> <asyncmap 0x0> <auth pap>] 5 rcvd [LCP ConfAck id=0x1 <asyncmap
>>>>> 0x0>] 6 sent [PAP AuthReq id=0x1 user="Mariner-T61"
>>>>> password=<hidden>] 7 rcvd [PAP AuthAck id=0x1]
>>>>> 8 PAP authentication succeeded
>>>>> 9 sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0>
>>>>> <ms-dns2 0.0.0.0>] 10 rcvd [IPCP ConfReq id=0x1 <addr 169.254.1.1>]
>>>>> 11 sent [IPCP ConfAck id=0x1 <addr 169.254.1.1>] 12 rcvd [IPCP
>>>>> ConfNak id=0x1 <ms-dns1 0.0.0.0> <ms-dns2 0.0.0.0>] 13 sent [IPCP
>>>>> ConfReq id=0x2 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns2 0.0.0.0>]
>>>>> 14 rcvd [IPCP ConfNak id=0x2 <ms-dns1 0.0.0.0> <ms-dns2 0.0.0.0>] 15
>>>>> sent [IPCP ConfReq id=0x3 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns2
>>>>> 0.0.0.0>] 16 rcvd [IPCP ConfNak id=0x3 <ms-dns1 0.0.0.0> <ms-dns2
>>>>> 0.0.0.0>] 17 sent [IPCP ConfReq id=0x4 <addr 0.0.0.0> <ms-dns1
>>>>> 0.0.0.0> <ms-dns2 0.0.0.0>] 18 rcvd [IPCP ConfNak id=0x4 <ms-dns1
>>>>> 0.0.0.0> <ms-dns2 0.0.0.0>] 19 sent [IPCP ConfReq id=0x5 <addr
>>>>> 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns2 0.0.0.0>] 20 rcvd [IPCP ConfNak
>>>>> id=0x5 <ms-dns1 0.0.0.0> <ms-dns2 0.0.0.0>] 21 sent [IPCP ConfReq
>>>>> id=0x6 <addr 0.0.0.0>] 22 rcvd [IPCP ConfNak id=0x6] 23 sent [IPCP
>>>>> ConfReq id=0x7 <addr 0.0.0.0>] 24 rcvd [IPCP ConfNak id=0x7]
>>>>>
>>>>>
>>>>> From what I see it looks good on your side. Are you still using the
>>>>> default barry-att_cingular scripts?
>>>>> Try running "sudo pppd dump debug call barry-att_cingular" so we can
>>>>> see what options pppd thinks are set.
>>>>>
>>>>> - Andy
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>
------------------------------------------------------------------------------
>>
>>
>>>>
>>>>> Create and Deploy Rich Internet Apps outside the browser with
>>>>> Adobe(R)AIR(TM) software. With Adobe AIR, Ajax developers can use
>>>>> existing skills and code to build responsive, highly engaging
>>>>> applications that combine the power of local resources and data with
>>>>> the reach of the web. Download the Adobe AIR SDK and Ajax docs to
>>>>> start building applications today-http://p.sf.net/sfu/adobe-com
>>>>>
>>>>>
>>>>>
>>>> Andy,
>>>>
>>>> Here's the output of the debug:
>>>>
>>>> pppd options in effect:
>>>> debug debug # (from /etc/ppp/peers/barry-att_cingular)
>>>>
>> nodetach #
>>
>>>> (from /etc/ppp/peers/barry-att_cingular) dump # (from
>>>>
>> command line)
>>
>>>> noauth # (from /etc/ppp/peers/barry-att_cingular) user
>>>>
>> # (from
>>
>>>> /etc/ppp/peers/barry-att_cingular) password ?????? # (from
>>>> /etc/ppp/peers/barry-att_cingular)
>>>> # (from /etc/ppp/options)
>>>> connect /usr/sbin/chat -f /etc/chatscripts/barry-
>>>>
>> att_cingular.chat #
>>
>>>> (from /etc/ppp/peers/barry-att_cingular) pty /usr/sbin/pppob -P
>>>> 3ewfdsxz # (from /etc/ppp/peers/barry- att_cingular)
nocrtscts #
>>>> (from /etc/ppp/peers/barry-att_cingular)
>>>> # (from /etc/ppp/options)
>>>> noaccomp # (from /etc/ppp/peers/barry-att_cingular)
>>>>
>> asyncmap 0 #
>>
>>>> (from /etc/ppp/options) nomagic # (from
>>>> /etc/ppp/peers/barry-att_cingular) mtu 1492 # (from
>>>> /etc/ppp/peers/barry-att_cingular) nopcomp # (from
>>>> /etc/ppp/peers/barry-att_cingular) passive # (from
>>>> /etc/ppp/peers/barry-att_cingular) lcp-echo-failure 999 #
>>>>
>> (from
>>
>>>> /etc/ppp/peers/barry-att_cingular) lcp-echo-interval 0 #
>>>>
>> (from
>>
>>>> /etc/ppp/peers/barry-att_cingular) hide-password # (from
>>>> /etc/ppp/options) novj # (from /etc/ppp/peers/barry-
>>>>
>> att_cingular)
>>
>>>> ipcp-accept-local # (from /etc/ppp/peers/barry-att_cingular)
>>>> ipcp-accept-remote # (from /etc/ppp/peers/barry-att_cingular)
>>>> noipdefault # (from /etc/ppp/peers/barry-
att_cingular) ipcp-
>>>>
>> restart 7
>>
>>>> # (from /etc/ppp/peers/barry-att_cingular) defaultroute #
>>>>
>> (from
>>
>>>> /etc/ppp/peers/barry-att_cingular) proxyarp # (from /
etc/ppp/
>>>>
>> options)
>>
>>>> usepeerdns # (from /etc/ppp/peers/barry-att_cingular)
>>>>
>> nobsdcomp #
>>
>>>> (from /etc/ppp/peers/barry-att_cingular) nodeflate # (from
>>>> /etc/ppp/peers/barry-att_cingular) noipx # (from /etc/ppp/
>>>>
>> options)
>>
>>>> The remainder of the process is the same. No IP address provided by
>>>> AT&T.
>>>>
>>>>
>>>>
>>> Shannon,
>>> Pleasea send me these two files from you system: /etc/ppp/options
>>> /etc/ppp/pap-secrets
>>>
>>> Thanks,
>>> - Andy
>>>
>>>
>>>
>>>
>>
------------------------------------------------------------------------------
>>
>>> Open Source Business Conference (OSBC), March 24-25, 2009, San
>>> Francisco, CA -OSBC tackles the biggest issue in open source: Open
>>> Sourcing the Enterprise -Strategies to boost innovation and cut costs
>>> with open source participation -Receive a $600 discount off the
>>> registration fee with the source code: SFAD
>>> http://p.sf.net/sfu/XcvMzF8H
>>>
>>>
>> Here's the file content. I'm using Pan now for news and I don't see
>> any good option to attach a file:
>>
>> # /etc/ppp/options
>> #
>> # Originally created by Jim Knoble
>> <jmkno...@mercury.interpath.net> # Modified
>> for Debian by alvar Bray
>> <al...@meiko.co.uk> # Modified for PPP
>> Server setup by Christoph Lameter
>> <clame...@debian.org> #
>> # To quickly see what options are active in this file, use this
>> command: # egrep -v '#|^ *$' /etc/ppp/options
>>
>> # Specify which DNS Servers the incoming Win95 or WinNT Connection
>> should use
>> # Two Servers can be remotely configured # ms-dns 192.168.1.1
>> # ms-dns 192.168.1.2
>>
>> # Specify which WINS Servers the incoming connection Win95 or WinNT
>> should use
>> # ms-wins 192.168.1.50
>> # ms-wins 192.168.1.51
>>
>> # Run the executable or shell command specified after pppd has #
>> terminated the link. This script could, for example, issue commands #
>> to the modem to cause it to hang up if hardware modem control signals #
>> were not available.
>> #disconnect "chat -- \d+++\d\c OK ath0 OK"
>>
>> # async character map -- 32-bit hex; each bit is a character # that
>> needs to be escaped for pppd to receive it. 0x00000001 # represents
>> '\x01', and 0x80000000 represents '\x1f'. asyncmap 0
>>
>> # Require the peer to authenticate itself before allowing network #
>> packets to be sent or received.
>> # Please do not disable this setting. It is expected to be standard in
>> # future releases of pppd. Use the call option (see manpage) to disable
>> # authentication for specific peers.
>> #auth
>> noauth
>> # ... Unfortunately, fixing this properly in the peers file #
>> (/etc/ppp/peers/ppp0, typically) is apparently incompatible with the #
>> paradigm used by gnome-system-tools and system-tools-backend for #
>> managing the peers files. So in Ubuntu Feisty we change the default.
>>
>> # Use hardware flow control (i.e. RTS/CTS) to control the flow of data
>> # on the serial port.
>> crtscts
>>
>> # Use software flow control (i.e. XON/XOFF) to control the flow of data
>> # on the serial port.
>> #xonxoff
>>
>> # Specifies that certain characters should be escaped on transmission #
>> (regardless of whether the peer requests them to be escaped with its #
>> async control character map). The characters to be escaped are #
>> specified as a list of hex numbers separated by commas. Note that #
>> almost any character can be specified for the escape option, unlike #
>> the asyncmap option which only allows control characters to be #
>> specified. The characters which may not be escaped are those with hex
>> # values 0x20 - 0x3f or 0x5e.
>> #escape 11,13,ff
>>
>> # Don't use the modem control lines.
>> #local
>>
>> # Specifies that pppd should use a UUCP-style lock on the serial device
>> # to ensure exclusive access to the device. lock
>>
>> # Don't show the passwords when logging the contents of PAP packets. #
>> This is the default.
>> hide-password
>>
>> # When logging the contents of PAP packets, this option causes pppd to
>> # show the password string in the log message. #show-password
>>
>> # Use the modem control lines. On Ultrix, this option implies hardware
>> # flow control, as for the crtscts option. (This option is not fully #
>> implemented.)
>> modem
>>
>> # Set the MRU [Maximum Receive Unit] value to <n> for negotiation.
>> pppd # will ask the peer to send packets of no more than <n> bytes. The
>> # minimum MRU value is 128. The default MRU value is 1500. A value of
>> # 296 is recommended for slow links (40 bytes for TCP/IP header + 256 #
>> bytes of data).
>> #mru 542
>>
>> # Set the interface netmask to <n>, a 32 bit netmask in "decimal dot" #
>> notation (e.g. 255.255.255.0).
>> #netmask 255.255.255.0
>>
>> # Disables the default behaviour when no local IP address is specified,
>> # which is to determine (if possible) the local IP address from the #
>> hostname. With this option, the peer will have to supply the local IP #
>> address during IPCP negotiation (unless it specified explicitly on the
>> # command line or in an options file). #noipdefault
>>
>> # Enables the "passive" option in the LCP. With this option, pppd will
>> # attempt to initiate a connection; if no reply is received from the #
>> peer, pppd will then just wait passively for a valid LCP packet from #
>> the peer (instead of exiting, as it does without this option). #passive
>>
>> # With this option, pppd will not transmit LCP packets to initiate a #
>> connection until a valid LCP packet is received from the peer (as for #
>> the "passive" option with old versions of pppd). #silent
>>
>> # Don't request or allow negotiation of any options for LCP and IPCP #
>> (use default values).
>> #-all
>>
>> # Disable Address/Control compression negotiation (use default, i.e. #
>> address/control field disabled).
>> #-ac
>>
>> # Disable asyncmap negotiation (use the default asyncmap, i.e. escape #
>> all control characters).
>> #-am
>>
>> # Don't fork to become a background process (otherwise pppd will do so
>> # if a serial device is specified).
>> #-detach
>>
>> # Disable IP address negotiation (with this option, the remote IP #
>> address must be specified with an option on the command line or in # an
>> options file).
>> #-ip
>>
>> # Disable IPCP negotiation and IP communication. This option should #
>> only be required if the peer is buggy and gets confused by requests #
>> from pppd for IPCP negotiation.
>> #noip
>>
>> # Disable magic number negotiation. With this option, pppd cannot #
>> detect a looped-back line.
>> #-mn
>>
>> # Disable MRU [Maximum Receive Unit] negotiation (use default, i.e. #
>> 1500).
>> #-mru
>>
>> # Disable protocol field compression negotiation (use default, i.e. #
>> protocol field compression disabled). #-pc
>>
>> # Require the peer to authenticate itself using PAP. #+pap
>>
>> # Don't agree to authenticate using PAP. #-pap
>>
>> # Require the peer to authenticate itself using CHAP [Cryptographic #
>> Handshake Authentication Protocol] authentication. #+chap
>>
>> # Don't agree to authenticate using CHAP. #-chap
>>
>> # Disable negotiation of Van Jacobson style IP header compression (use
>> # default, i.e. no compression).
>> #-vj
>>
>> # Increase debugging level (same as -d). If this option is given, pppd
>> # will log the contents of all control packets sent or received in a #
>> readable form. The packets are logged through syslog with facility #
>> daemon and level debug. This information can be directed to a file by #
>> setting up /etc/syslog.conf appropriately (see syslog.conf(5)). (If #
>> pppd is compiled with extra debugging enabled, it will log messages #
>> using facility local2 instead of daemon). #debug
>>
>> # Append the domain name <d> to the local host name for authentication
>> # purposes. For example, if gethostname() returns the name porsche, #
>> but the fully qualified domain name is porsche.Quotron.COM, you would #
>> use the domain option to set the domain name to Quotron.COM. #domain
>> <d>
>>
>> # Enable debugging code in the kernel-level PPP driver. The argument n
>> # is a number which is the sum of the following values: 1 to enable #
>> general debug messages, 2 to request that the contents of received #
>> packets be printed, and 4 to request that the contents of transmitted #
>> packets be printed.
>> #kdebug n
>>
>> # Set the MTU [Maximum Transmit Unit] value to <n>. Unless the peer #
>> requests a smaller value via MRU negotiation, pppd will request that #
>> the kernel networking code send data packets of no more than n bytes #
>> through the PPP network interface.
>> #mtu <n>
>>
>> # Set the name of the local system for authentication purposes to <n>.
>> # This is a privileged option. With this option, pppd will use lines in
>> the
>> # secrets files which have <n> as the second field when looking for a #
>> secret to use in authenticating the peer. In addition, unless
>> overridden # with the user option, <n> will be used as the name to send
>> to the peer # when authenticating the local system to the peer. (Note
>> that pppd does # not append the domain name to <n>.) #name <n>
>>
>> # Enforce the use of the hostname as the name of the local system for #
>> authentication purposes (overrides the name option). #usehostname
>>
>> # Set the assumed name of the remote system for authentication purposes
>> # to <n>.
>> #remotename <n>
>>
>> # Add an entry to this system's ARP [Address Resolution Protocol] #
>> table with the IP address of the peer and the Ethernet address of this
>> # system.
>> proxyarp
>>
>> # Use the system password database for authenticating the peer using #
>> PAP. Note: mgetty already provides this option. If this is specified #
>> then dialin from users using a script under Linux to fire up ppp wont
>> work.
>> # login
>>
>> # If this option is given, pppd will send an LCP echo-request frame to
>> the # peer every n seconds. Normally the peer should respond to the
>> echo- request
>> # by sending an echo-reply. This option can be used with the #
>> lcp-echo-failure option to detect that the peer is no longer connected.
>> lcp-echo-interval 30
>>
>> # If this option is given, pppd will presume the peer to be dead if n #
>> LCP echo-requests are sent without receiving a valid LCP echo-reply. #
>> If this happens, pppd will terminate the connection. Use of this #
>> option requires a non-zero value for the lcp-echo-interval parameter. #
>> This option can be used to enable pppd to terminate after the physical
>> # connection has been broken (e.g., the modem has hung up) in #
>> situations where no hardware modem control lines are available.
>> lcp-echo-failure 4
>>
>> # Set the LCP restart interval (retransmission timeout) to <n> seconds
>> # (default 3).
>> #lcp-restart <n>
>>
>> # Set the maximum number of LCP terminate-request transmissions to <n>
>> # (default 3).
>> #lcp-max-terminate <n>
>>
>> # Set the maximum number of LCP configure-request transmissions to <n>
>> # (default 10).
>> #lcp-max-configure <n>
>>
>> # Set the maximum number of LCP configure-NAKs returned before starting
>> # to send configure-Rejects instead to <n> (default 10).
>> #lcp-max-failure <n>
>>
>> # Set the IPCP restart interval (retransmission timeout) to <n> #
>> seconds (default 3).
>> #ipcp-restart <n>
>>
>> # Set the maximum number of IPCP terminate-request transmissions to <n>
>> # (default 3).
>> #ipcp-max-terminate <n>
>>
>> # Set the maximum number of IPCP configure-request transmissions to <n>
>> # (default 10).
>> #ipcp-max-configure <n>
>>
>> # Set the maximum number of IPCP configure-NAKs returned before
>> starting # to send configure-Rejects instead to <n> (default 10).
>> #ipcp-max-failure <n>
>>
>> # Set the PAP restart interval (retransmission timeout) to <n> seconds
>> # (default 3).
>> #pap-restart <n>
>>
>> # Set the maximum number of PAP authenticate-request transmissions to #
>> <n> (default 10).
>> #pap-max-authreq <n>
>>
>> # Set the maximum time that pppd will wait for the peer to authenticate
>> # itself with PAP to <n> seconds (0 means no limit). #pap-timeout <n>
>>
>> # Set the CHAP restart interval (retransmission timeout for #
>> challenges) to <n> seconds (default 3). #chap-restart <n>
>>
>> # Set the maximum number of CHAP challenge transmissions to <n> #
>> (default 10).
>> #chap-max-challenge
>>
>> # If this option is given, pppd will rechallenge the peer every <n> #
>> seconds.
>> #chap-interval <n>
>>
>> # With this option, pppd will accept the peer's idea of our local IP #
>> address, even if the local IP address was specified in an option.
>> #ipcp-accept-local
>>
>> # With this option, pppd will accept the peer's idea of its (remote) IP
>> # address, even if the remote IP address was specified in an option.
>> #ipcp-accept-remote
>>
>> # Disable the IPXCP and IPX protocols. # To let pppd pass IPX packets
>> comment this out --- you'll probably also # want to install ipxripd,
>> and have the Internal IPX Network option enabled
>> # in your kernel. /usr/doc/HOWTO/IPX-HOWTO.gz contains more info.
>> noipx
>>
>> # Exit once a connection has been made and terminated. This is the
>> default,
>> # unless the `persist' or `demand' option has been specified.
>> #nopersist
>>
>> # Do not exit after a connection is terminated; instead try to reopen #
>> the connection.
>> #persist
>>
>> # Terminate after n consecutive failed connection attempts. # A value
>> of 0 means no limit. The default value is 10. #maxfail <n>
>>
>> # Initiate the link only on demand, i.e. when data traffic is present.
>> # With this option, the remote IP address must be specified by the user
>> on # the command line or in an options file. Pppd will initially
>> configure # the interface and enable it for IP traffic without
>> connecting to the peer.
>> # When traffic is available, pppd will connect to the peer and perform
>> # negotiation, authentication, etc. When this is completed, pppd will
>> # commence passing data packets (i.e., IP packets) across the link.
>> #demand
>>
>> # Specifies that pppd should disconnect if the link is idle for <n>
>> seconds.
>> # The link is idle when no data packets (i.e. IP packets) are being
>> sent or
>> # received. Note: it is not advisable to use this option with the
>> persist # option without the demand option. If the active-filter
>> option is given, # data packets which are rejected by the specified
>> activity filter also # count as the link being idle.
>> #idle <n>
>>
>> # Specifies how many seconds to wait before re-initiating the link
>> after # it terminates. This option only has any effect if the persist
>> or demand # option is used. The holdoff period is not applied if the
>> link was # terminated because it was idle.
>> #holdoff <n>
>>
>> # Wait for up n milliseconds after the connect script finishes for a
>> valid # PPP packet from the peer. At the end of this time, or when a
>> valid PPP # packet is received from the peer, pppd will commence
>> negotiation by # sending its first LCP packet. The default value is
>> 1000 (1 second). # This wait period only applies if the connect or pty
>> option is used. #connect-delay <n>
>>
>> # Packet filtering: for more information, see pppd(8) # Any packets
>> matching the filter expression will be interpreted as link # activity,
>> and will cause a "demand" connection to be activated, and reset
>> # the idle connection timer. (idle option) # The filter expression is
>> akin to that of tcpdump(1) #active-filter <filter-expression>
>>
>> # ---<End of File>---
>>
>> # /etc/ppp/pap-secrets
>> #
>> # This is a pap-secrets file to be used with the AUTO_PPP function of #
>> mgetty. mgetty-0.99 is preconfigured to startup pppd with the login
>> option
>> # which will cause pppd to consult /etc/passwd (and /etc/shadow in
>> turn) # after a user has passed this file. Don't be disturbed therefore
>> by the fact
>> # that this file defines logins with any password for users.
>> /etc/passwd # (again, /etc/shadow, too) will catch passwd mismatches. #
>> # This file should block ALL users that should not be able to do
>> AUTO_PPP. # AUTO_PPP bypasses the usual login program so it's necessary
>> to list all # system userids with regular passwords here. #
>> # ATTENTION: The definitions here can allow users to login without a #
>> password if you don't use the login option of pppd! The mgetty Debian #
>> package already provides this option; make sure you don't change that.
>>
>> # INBOUND connections
>>
>> # Every regular user can use PPP and has to use passwords from
>> /etc/passwd * hostname "" *
>>
>> # UserIDs that cannot use PPP at all. Check your /etc/passwd and add
>> any # other accounts that should not be able to use pppd! guest
>> hostname "*" -
>> master hostname "*" -
>> root hostname "*" -
>> support hostname "*" -
>> stats hostname "*" -
>>
>> # OUTBOUND connections
>>
>> # Here you should add your userid password to connect to your providers
>> via
>> # PAP. The * means that the password is to be used for ANY host you
>> connect
>> # to. Thus you do not have to worry about the foreign machine name.
>> Just # replace password with your password. # If you have different
>> providers with different passwords then you better # remove the
>> following line.
>>
>> # * password
>>
>>
> Shannon,
> These are the active options in your file. asyncmap 0
> noauth
> crtscts
> lock
> hide-password
> modem
> proxyarp
> lcp-echo-interval 30
> lcp-echo-failure 4
> noipx
>
>
> Try making a backup of your options file and create a new one with these
> entries:
>
> sudo su -
> cd /etc/ppp
> mv options options.org
> vi options
>
> add these:
> lock
> noauth
> noipdefault
> usepeerdns
>
> Save the file and change permissions to 644 chmod 644 options
>
> Try connecting again and post the output.
>
> - Andy
>
>
------------------------------------------------------------------------------
> Open Source Business Conference (OSBC), March 24-25, 2009, San
> Francisco, CA -OSBC tackles the biggest issue in open source: Open
> Sourcing the Enterprise -Strategies to boost innovation and cut costs
> with open source participation -Receive a $600 discount off the
> registration fee with the source code: SFAD http://p.sf.net/sfu/XcvMzF8H
Same thing with new options. Here's the top of the debug output:
pppd options in effect:
debug debug # (from /etc/ppp/peers/barry-att_cingular)
nodetach # (from /etc/ppp/peers/barry-att_cingular)
dump # (from command line)
noauth # (from /etc/ppp/peers/barry-att_cingular)
user # (from /etc/ppp/peers/barry-att_cingular)
password ?????? # (from /etc/ppp/peers/barry-att_cingular)
# (from /etc/ppp/options)
connect /usr/sbin/chat -f /etc/chatscripts/barry-
att_cingular.chat # (from /etc/ppp/peers/barry-att_cingular)
pty /usr/sbin/pppob -P 3ewfdsxz # (from /etc/ppp/peers/barry-
att_cingular)
nocrtscts # (from /etc/ppp/peers/barry-att_cingular)
# (from /etc/ppp/options)
noaccomp # (from /etc/ppp/peers/barry-att_cingular)
asyncmap 0 # (from /etc/ppp/options)
nomagic # (from /etc/ppp/peers/barry-att_cingular)
mtu 1492 # (from /etc/ppp/peers/barry-att_cingular)
nopcomp # (from /etc/ppp/peers/barry-att_cingular)
passive # (from /etc/ppp/peers/barry-att_cingular)
lcp-echo-failure 999 # (from /etc/ppp/peers/barry-att_cingular)
lcp-echo-interval 0 # (from /etc/ppp/peers/barry-att_cingular)
hide-password # (from /etc/ppp/options)
novj # (from /etc/ppp/peers/barry-att_cingular)
ipcp-accept-local # (from /etc/ppp/peers/barry-att_cingular)
ipcp-accept-remote # (from /etc/ppp/peers/barry-att_cingular)
noipdefault # (from /etc/ppp/peers/barry-att_cingular)
ipcp-restart 7 # (from /etc/ppp/peers/barry-att_cingular)
defaultroute # (from /etc/ppp/peers/barry-att_cingular)
proxyarp # (from /etc/ppp/options)
usepeerdns # (from /etc/ppp/peers/barry-att_cingular)
nobsdcomp # (from /etc/ppp/peers/barry-att_cingular)
nodeflate # (from /etc/ppp/peers/barry-att_cingular)
noipx # (from /etc/ppp/options)
------------------------------------------------------------------------------
Open Source Business Conference (OSBC), March 24-25, 2009, San Francisco, CA
-OSBC tackles the biggest issue in open source: Open Sourcing the Enterprise
-Strategies to boost innovation and cut costs with open source participation
-Receive a $600 discount off the registration fee with the source code: SFAD
http://p.sf.net/sfu/XcvMzF8H
_______________________________________________
Barry-devel mailing list
Barry-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/barry-devel
