Michael,
I finally found the problem. It turned out that b43_rfkill_soft_toggle()
was returning -EBUSY even when there was no error. I also changed the
logic in the request_module("rfkill-input") section. Now, the code is
only compiled if rfkill-input is not built-in.
AFAIK, it is ready for John, and should be pushed into Linus's tree as
well.
Larry
---
From: Larry Finger <[EMAIL PROTECTED]>
This fixes Bug #9414
Since addition of the rfkill callback, the LED associated with the off
switch on the radio has not worked for several reasons:
(1) Essential data in the rfkill structure were missing.
(2) The rfkill structure was initialized after the LED initialization.
(3) There was a minor memory leak if the radio LED structure was inited.
Once the above problems were fixed, additional difficulties were noted:
(4) The radio LED was in the wrong state at startup.
(5) The radio switch had to be manipulated twice for each state change.
(6) A circular mutex locking situation existed.
(7) If rfkill-input is built as a module, it is not automatically loaded.
This patch fixes all of the above.
Signed-off-by: Larry Finger <[EMAIL PROTECTED]>
Signed-off-by: Michael Buesch <[EMAIL PROTECTED]>
Index: wireless-2.6/drivers/net/wireless/b43/rfkill.c
===================================================================
--- wireless-2.6.orig/drivers/net/wireless/b43/rfkill.c
+++ wireless-2.6/drivers/net/wireless/b43/rfkill.c
@@ -25,6 +25,8 @@
#include "rfkill.h"
#include "b43.h"
+#include <linux/kmod.h>
+
/* Returns TRUE, if the radio is enabled in hardware. */
static bool b43_is_hw_radio_enabled(struct b43_wldev *dev)
@@ -50,7 +52,10 @@ static void b43_rfkill_poll(struct input
bool report_change = 0;
mutex_lock(&wl->mutex);
- B43_WARN_ON(b43_status(dev) < B43_STAT_INITIALIZED);
+ if (unlikely(b43_status(dev) < B43_STAT_INITIALIZED)) {
+ mutex_unlock(&wl->mutex);
+ return;
+ }
enabled = b43_is_hw_radio_enabled(dev);
if (unlikely(enabled != dev->radio_hw_enable)) {
dev->radio_hw_enable = enabled;
@@ -60,8 +65,12 @@ static void b43_rfkill_poll(struct input
}
mutex_unlock(&wl->mutex);
- if (unlikely(report_change))
- input_report_key(poll_dev->input, KEY_WLAN, enabled);
+ /* send the radio switch event to the system - note both a key press
+ * and a release are required */
+ if (unlikely(report_change)) {
+ input_report_key(poll_dev->input, KEY_WLAN, 1);
+ input_report_key(poll_dev->input, KEY_WLAN, 0);
+ }
}
/* Called when the RFKILL toggled in software. */
@@ -69,13 +78,15 @@ static int b43_rfkill_soft_toggle(void *
{
struct b43_wldev *dev = data;
struct b43_wl *wl = dev->wl;
- int err = 0;
+ int err = -EBUSY;
if (!wl->rfkill.registered)
return 0;
mutex_lock(&wl->mutex);
- B43_WARN_ON(b43_status(dev) < B43_STAT_INITIALIZED);
+ if (b43_status(dev) < B43_STAT_INITIALIZED)
+ goto out_unlock;
+ err = 0;
switch (state) {
case RFKILL_STATE_ON:
if (!dev->radio_hw_enable) {
@@ -133,9 +144,25 @@ void b43_rfkill_init(struct b43_wldev *d
rfk->poll_dev->poll = b43_rfkill_poll;
rfk->poll_dev->poll_interval = 1000; /* msecs */
+ rfk->poll_dev->input->name = rfk->name;
+ rfk->poll_dev->input->id.bustype = BUS_HOST;
+ rfk->poll_dev->input->id.vendor = dev->dev->bus->boardinfo.vendor;
+ rfk->poll_dev->input->evbit[0] = BIT(EV_KEY);
+ set_bit(KEY_WLAN, rfk->poll_dev->input->keybit);
+
err = rfkill_register(rfk->rfkill);
if (err)
goto err_free_polldev;
+
+#ifndef CONFIG_RFKILL_INPUT
+ /* B43 RF-kill isn't useful without the rfkill-input subsystem.
+ * Try to load the module. */
+ err = request_module("rfkill-input");
+ if (err)
+ b43warn(wl, "Failed to load the rfkill-input module. "
+ "The built-in radio LED will not work.\n");
+#endif /* CONFIG_RFKILL_INPUT */
+
err = input_register_polled_device(rfk->poll_dev);
if (err)
goto err_unreg_rfk;
Index: wireless-2.6/drivers/net/wireless/b43/main.c
===================================================================
--- wireless-2.6.orig/drivers/net/wireless/b43/main.c
+++ wireless-2.6/drivers/net/wireless/b43/main.c
@@ -2165,7 +2165,6 @@ static void b43_mgmtframe_txantenna(stru
static void b43_chip_exit(struct b43_wldev *dev)
{
b43_radio_turn_off(dev, 1);
- b43_leds_exit(dev);
b43_gpio_cleanup(dev);
/* firmware is released later */
}
@@ -2193,11 +2192,10 @@ static int b43_chip_init(struct b43_wlde
err = b43_gpio_init(dev);
if (err)
goto out; /* firmware is released later */
- b43_leds_init(dev);
err = b43_upload_initvals(dev);
if (err)
- goto err_leds_exit;
+ goto err_gpio_clean;
b43_radio_turn_on(dev);
b43_write16(dev, 0x03E6, 0x0000);
@@ -2273,8 +2271,7 @@ out:
err_radio_off:
b43_radio_turn_off(dev, 1);
-err_leds_exit:
- b43_leds_exit(dev);
+err_gpio_clean:
b43_gpio_cleanup(dev);
return err;
}
@@ -3301,10 +3298,7 @@ static void b43_wireless_core_exit(struc
return;
b43_set_status(dev, B43_STAT_UNINIT);
- mutex_unlock(&dev->wl->mutex);
- b43_rfkill_exit(dev);
- mutex_lock(&dev->wl->mutex);
-
+ b43_leds_exit(dev);
b43_rng_exit(dev->wl);
b43_pio_free(dev);
b43_dma_free(dev);
@@ -3426,12 +3420,12 @@ static int b43_wireless_core_init(struct
memset(wl->mac_addr, 0, ETH_ALEN);
b43_upload_card_macaddress(dev);
b43_security_init(dev);
- b43_rfkill_init(dev);
b43_rng_init(wl);
b43_set_status(dev, B43_STAT_INITIALIZED);
- out:
+ b43_leds_init(dev);
+out:
return err;
err_chip_exit:
@@ -3520,6 +3514,10 @@ static int b43_op_start(struct ieee80211
int did_init = 0;
int err = 0;
+ /* First register RFkill.
+ * LEDs that are registered later depend on it. */
+ b43_rfkill_init(dev);
+
mutex_lock(&wl->mutex);
if (b43_status(dev) < B43_STAT_INITIALIZED) {
@@ -3549,6 +3547,8 @@ static void b43_op_stop(struct ieee80211
struct b43_wl *wl = hw_to_b43_wl(hw);
struct b43_wldev *dev = wl->current_dev;
+ b43_rfkill_exit(dev);
+
mutex_lock(&wl->mutex);
if (b43_status(dev) >= B43_STAT_STARTED)
b43_wireless_core_stop(dev);
Index: wireless-2.6/drivers/net/wireless/b43/leds.c
===================================================================
--- wireless-2.6.orig/drivers/net/wireless/b43/leds.c
+++ wireless-2.6/drivers/net/wireless/b43/leds.c
@@ -163,6 +163,9 @@ static void b43_map_led(struct b43_wldev
b43_register_led(dev, &dev->led_radio, name,
b43_rfkill_led_name(dev),
led_index, activelow);
+ /* Sync the RF-kill LED state with the switch state. */
+ if (dev->radio_hw_enable)
+ b43_led_turn_on(dev, led_index, activelow);
break;
case B43_LED_WEIRD:
case B43_LED_ASSOC:
@@ -232,4 +235,5 @@ void b43_leds_exit(struct b43_wldev *dev
b43_unregister_led(&dev->led_tx);
b43_unregister_led(&dev->led_rx);
b43_unregister_led(&dev->led_assoc);
+ b43_unregister_led(&dev->led_radio);
}
_______________________________________________
Bcm43xx-dev mailing list
Bcm43xx-dev@lists.berlios.de
https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
