As usual, forgot to CC the list... ---------- Forwarded message ---------- From: Stefanik Gábor <[EMAIL PROTECTED]> Date: Apr 18, 2008 1:19 PM Subject: Re: ASUS WL-138G v2 working with different sprom values To: kala mazoo <[EMAIL PROTECTED]>
I seem to have a clue about what's going on here. In Buesch's non-working driver output, there was a line saying "HW CONFIG: freq=2412". Your card now gives "HW CONFIG: channel=1 freq=2412 phymode=2". "Channel=1" and "freq=2412" are equivalent, so I think that the real problem is the lack of "phymode=2". Also, I am now back to my linux box, and I'm gonna test which SPROM value is causing b43 to freak out. I'll come back (hopefully) with results later. On 4/18/08, kala mazoo <[EMAIL PROTECTED]> wrote: > > > Greets, > > Following up on this idea of substituting sprom images; > > > Oops, sorry, here is the attached SPROM file.> > > > >On Tue, Apr 15, 2008 at 11:39 PM, Stefanik Gábor > >wrote: > > > > Looks like this is an Asus-specific issue. Can you try flashing the > > attached SPROM file (with a modified MAC address, of course) into your > card > > to see if it results in *any* transmission? (Back up your SPROM first!) > This > > is from a non-Asus 4318/02, extracted from a working card. (I can't test > it > > myself now, as I don't have a usable Linux system ATM.) > > > > > > Using that sprom dump which Stefanik provided, the card in question here > appears to be now working (although I've not yet tested it at any length) > > ----- > > b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02) > b43-phy0 debug: Chip initialized > b43-phy0 debug: 32-bit DMA initialized > Registered led device: b43-phy0:tx > Registered led device: b43-phy0:rx > b43-phy0 debug: Wireless interface started > HW CONFIG: channel=1 freq=2412 phymode=2 > b43-phy0 debug: Adding Interface type 2 > b43-phy0 debug: Using hardware based encryption for keyidx: 0, mac: > ff:ff:ff:ff:ff:ff > ADDRCONF(NETDEV_UP): wlan0: link is not ready > wlan0: Initial auth_alg=0 > wlan0: authenticate with AP 00:1e:2a:61:7d:2c > wlan0: RX authentication from 00:1e:2a:61:7d:2c (alg=0 transaction=2 > status=0) > wlan0: authenticated > wlan0: associated with AP 00:1e:2a:61:7d:2c > wlan0: associated > phy0: Added STA 00:1e:2a:61:7d:2c > ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready > > ------ > > This was using a pristine 2.6.24 tree on 32bit ix86 -- only the sprom > contents were > changed. I'll check this on my 64bit machine a bit later -- I'll test out > and monitor > this (now working) card to make sure it remains sane. > > Hopefully this provides a clue as to what's going on. > > Oh...btw, I doubt I've ever seen the led devices registering themselves > before (with > the shipped sprom contents that is) ... > > Regards, > > Donald > _________________________________________________________________ > You dream job is up for grabs. Grab it. > http://mycareer.com.au/?s_cid=596065 > _______________________________________________ > Bcm43xx-dev mailing list > Bcm43xx-dev@lists.berlios.de > https://lists.berlios.de/mailman/listinfo/bcm43xx-dev > -- Vista: [V]iruses, [I]ntruders, [S]pyware, [T]rojans and [A]dware. :-) -- Vista: [V]iruses, [I]ntruders, [S]pyware, [T]rojans and [A]dware. :-)
_______________________________________________ Bcm43xx-dev mailing list Bcm43xx-dev@lists.berlios.de https://lists.berlios.de/mailman/listinfo/bcm43xx-dev