On Dec 29, 2013 8:08 AM, "Christian" <j...@wispa.de> wrote: > > Hi folks, > > I got a 4 GB SD-card that does work well with my BeagleBoard xM, see attachment “BeagleBoard booting SuSE on 4GB-SD ok.txt“. I cloned that card just to have a backup if that card gets corrupted one day. I did so using dd and ended up with a clone that boots just a bit. Booting the clone fails as soon as disc mmc-00000_0x0f4de006-part2 has to bee mounted, see attachment “BeagleBoard booting SuSE on 8GB-SD fails.txt”. > > I don't have the slightest idea what is going wrong. The original 4 GB works just fine but the same image cloned / transferred to an 8 GB card (that should easily do) fails?! Could anybody help me out with just an idea what do to or where to search?
You can't clone the disks uuid label. Fix that label variable for what the 8gb card actually is and it'll boot.. > > Beat regards > > Christian > > BeagleBoard booting SuSE on 4GB-SD ok.txt > > fdisk -l /dev/sdc > > Platte /dev/sdc: 3974 MByte, 3974103040 Byte > 255 Köpfe, 63 Sektoren/Spur, 483 Zylinder, zusammen 7761920 Sektoren > Einheiten = Sektoren von 1 × 512 = 512 Bytes > Sector size (logical/physical): 512 bytes / 512 bytes > I/O size (minimum/optimal): 512 bytes / 512 bytes > Disk identifier: 0x64c9641e > > Gerät boot. Anfang Ende Blöcke Id System > /dev/sdc1 * 2048 411655 204804 83 Linux > /dev/sdc2 411656 6731235 3159790 83 Linux > /dev/sdc3 6731240 7759394 514077+ 82 Linux Swap / Solaris > > OMAP SD/MMC: 0 > > U-Boot 2013.04-rc2 (Apr 17 2013 - 07:41:39) > > OMAP36XX/37XX-GP ES1.2, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz > OMAP3 Beagle board + LPDDR/NAND > I2C: ready > DRAM: 512 MiB > NAND: 0 MiB > MMC: OMAP SD/MMC: 0 > *** Warning - readenv() failed, using default environment > > In: serial > Out: serial > Err: serial > Beagle xM Rev C > No EEPROM on expansion board > Die ID #452000029ff800000168580217028015 > musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) > musb-hdrc: MHDRC RTL version 1.800 > musb-hdrc: setup fifo_mode 4 > musb-hdrc: 28/31 max ep, 16384/16384 memory > USB Peripheral mode controller at 480ab000 using PIO, IRQ 0 > Net: usb_ether > Hit any key to stop autoboot: 0 > mmc0 is current device > gpio: pin 173 (gpio 173) value is 0 > gpio: pin 4 (gpio 4) value is 0 > SD/MMC found on device 0 > ** File not found uEnv.txt ** > 1516 bytes read in 9 ms (164.1 KiB/s) > Running bootscript from mmc0 ... > ## Executing script at 80200000 > kerneladdr=0x80200000 > ramdiskaddr=0x81000000 > mmc0 is current device > 4242872 bytes read in 338 ms (12 MiB/s) > 4351196 bytes read in 333 ms (12.5 MiB/s) > ## Booting kernel from Legacy Image at 80200000 ... > Image Name: Linux-3.7.10-1.16-omap2plus > Image Type: ARM Linux Kernel Image (uncompressed) > Data Size: 4242808 Bytes = 4 MiB > Load Address: 80008000 > Entry Point: 80008000 > Verifying Checksum ... OK > ## Loading init Ramdisk from Legacy Image at 81000000 ... > Image Name: Initrd > Image Type: ARM Linux RAMDisk Image (uncompressed) > Data Size: 4351132 Bytes = 4.1 MiB > Load Address: 00000000 > Entry Point: 00000000 > Verifying Checksum ... OK > Loading Kernel Image ... OK > OK > > Starting kernel ... > > // many lines cut off here > > Boot logging started on /dev/ttyO2(/dev/console) at Mon Sep 2 02:00:05 2013 > Waiting for device /dev/disk/by-id/mmc-00000_0x0f4de006-part2 to appear: ok > fsck from util-linux 2.21.2 > [/sbin/fsck.ext4 (1) -- /] fsck.ext4 -a /dev/mmcblk0p2 > /dev/mmcblk0p2: clean, 24847/195200 files, 188497/789947 blocks > fsck succeeded. Mounting root device read-write. > Mounting root /dev/disk/by-id/mmc-00000_0x0f4de006-part2 > mount -o rw,noatime,nobarrier -t ext4 /dev/disk/by-id/mmc-00000_0x0f4de006-part2 /root > [ 10.257232] EXT4-fs (mmcblk0p2): barriers disabled > [ 10.347106] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: nobarrier > [ 11.011016] EXT4-fs (mmcblk0p2): re-mounted. Opts: nobarrier > [ 12.021148] systemd[1]: systemd 195 running in system mode. (+PAM +LIBWRAP +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ; suse) > > Welcome to openSUSE 12.3 (Dartmouth) (armv7hl)! > > BeagleBoard booting SuSE on 8GB-SD fails.txt > > fdisk -l /dev/sdc > > Platte /dev/sdc: 7969 MByte, 7969177600 Byte > 255 Köpfe, 63 Sektoren/Spur, 968 Zylinder, zusammen 15564800 Sektoren > Einheiten = Sektoren von 1 × 512 = 512 Bytes > Sector size (logical/physical): 512 bytes / 512 bytes > I/O size (minimum/optimal): 512 bytes / 512 bytes > Disk identifier: 0x64c9641e > > Gerät boot. Anfang Ende Blöcke Id System > /dev/sdc1 * 2048 411655 204804 83 Linux > /dev/sdc2 411656 6731235 3159790 83 Linux > /dev/sdc3 6731240 7759394 514077+ 82 Linux Swap / Solaris > > OMAP SD/MMC: 0 > > U-Boot 2013.04-rc2 (Apr 17 2013 - 07:41:39) > > OMAP36XX/37XX-GP ES1.2, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz > OMAP3 Beagle board + LPDDR/NAND > I2C: ready > DRAM: 512 MiB > NAND: 0 MiB > MMC: OMAP SD/MMC: 0 > *** Warning - readenv() failed, using default environment > > In: serial > Out: serial > Err: serial > Beagle xM Rev C > No EEPROM on expansion board > Die ID #452000029ff800000168580217028015 > musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) > musb-hdrc: MHDRC RTL version 1.800 > musb-hdrc: setup fifo_mode 4 > musb-hdrc: 28/31 max ep, 16384/16384 memory > USB Peripheral mode controller at 480ab000 using PIO, IRQ 0 > Net: usb_ether > Hit any key to stop autoboot: 0 > mmc0 is current device > gpio: pin 173 (gpio 173) value is 0 > gpio: pin 4 (gpio 4) value is 0 > SD/MMC found on device 0 > ** File not found uEnv.txt ** > 1516 bytes read in 7 ms (210.9 KiB/s) > Running bootscript from mmc0 ... > ## Executing script at 80200000 > kerneladdr=0x80200000 > ramdiskaddr=0x81000000 > mmc0 is current device > 4242872 bytes read in 320 ms (12.6 MiB/s) > 4351196 bytes read in 318 ms (13 MiB/s) > ## Booting kernel from Legacy Image at 80200000 ... > Image Name: Linux-3.7.10-1.16-omap2plus > Image Type: ARM Linux Kernel Image (uncompressed) > Data Size: 4242808 Bytes = 4 MiB > Load Address: 80008000 > Entry Point: 80008000 > Verifying Checksum ... OK > ## Loading init Ramdisk from Legacy Image at 81000000 ... > Image Name: Initrd > Image Type: ARM Linux RAMDisk Image (uncompressed) > Data Size: 4351132 Bytes = 4.1 MiB > Load Address: 00000000 > Entry Point: 00000000 > Verifying Checksum ... OK > Loading Kernel Image ... OK > OK > > Starting kernel ... > > // many lines cut off here > > Creating device nodes with udev > [ 7.418151] systemd-udevd[90]: starting version 195 > mount: devpts is already mounted or /dev/pts busy > devpts is already mounted on /dev/pts > Boot logging started on /dev/ttyO2(/dev/console) at Mon Sep 2 02:00:05 2013 > Waiting for device /dev/disk/by-id/mmc-00000_0x0f4de006-part2 to appear: ..............................Could not find /dev/disk/by-id/mmc-00000_0x0f4de006-part2. > Want me to fall back to /dev/disk/by-id/mmc-00000_0x0f4de006-part2? (Y/n) > > -- > For more options, visit http://beagleboard.org/discuss > --- > You received this message because you are subscribed to the Google Groups "BeagleBoard" group. > To unsubscribe from this group and stop receiving emails from it, send an email to beagleboard+unsubscr...@googlegroups.com. > For more options, visit https://groups.google.com/groups/opt_out. -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to beagleboard+unsubscr...@googlegroups.com. For more options, visit https://groups.google.com/groups/opt_out.
