Still could be the same issue. What buffer are you using to drive the signals to the LVDS device? Are the trace lengths match to insure that all the setup and hold times are met by having all signals with the same delay?
Gerald On Wed, Jul 30, 2014 at 9:40 AM, James S <s190...@gmail.com> wrote: > Hi Gerald, thanks for that reminder. > > However, there should be no such loading on the White since it doesn't > have HDMI on board? The problem also occurs on the White. What else could > it be? > > Regards, > James > > > On Wednesday, July 30, 2014 3:16:18 PM UTC+1, James S wrote: > >> We have a built a custom board with an LCD interface to drive a 1024 x >> 768 pixel LVDS panel, 16BPP. It works great on the Beaglebone White with >> the old Angstrom 3.2 using the board file configuration. >> >> We want to use the Beaglebone Black so we built up a system from >> http://elinux.org/Beagleboard:BeagleBoneBlack_Debian#2014-07-22 . I >> added a dts using the same parameters from the old board file but the >> graphics are blurred and corrupted. The card I made boots on the White also >> and gives the same results as on the Black. See images below. >> >> I’ve fiddled with the panel timings but they don’t seem to have any >> effect. >> >> Does anyone have any idea what is wrong and how do I fix it? >> >> Regards, >> >> James >> >> >> >> This is part of the (good) image from the frame buffer. >> >> >> <https://lh6.googleusercontent.com/-4paVjDS0NME/U9j9QP7ZvyI/AAAAAAAAGjY/Tq2jYoa6r0Y/s1600/screen1.jpg> >> >> >> >> >> >> >> >> >> >> >> >> This is a photo of the output on the screen, showing a similar area. >> >> >> <https://lh6.googleusercontent.com/-qR11mE7KhYU/U9j9wMohRZI/AAAAAAAAGjg/_lhBqXIQQyk/s1600/screen2.jpg> >> >> >> >> >> >> >> >> >> >> >> The following is the panel section of the dts file, based on an LCD4 dts:- >> >> >> >> /* Settings for AUO G121XN01 / mita cape: */ >> >> panel { >> >> compatible = "tilcdc,panel"; >> >> pinctrl-names = "default"; >> >> pinctrl-0 = <&bone_mita_cape_lcd_pins>; >> >> panel-info { >> >> ac-bias = <255>; >> >> ac-bias-intrpt = <0>; >> >> dma-burst-sz = <16>; >> >> bpp = <16>; >> >> fdd = <0x80>; >> >> tft-alt-mode = <0>; >> >> stn-565-mode = <0>; >> >> mono-8bit-mode = <0>; >> >> sync-edge = <0>; >> >> sync-ctrl = <1>; >> >> raster-order = <0>; >> >> fifo-th = <0>; >> >> invert-pxl-clk = <0>; >> >> }; >> >> display-timings { >> >> native-mode = <&timing0>; >> >> timing0: 1024x768 { >> >> hactive = <1024>; >> >> vactive = <768>; >> >> hback-porch = <80>; >> >> hfront-porch = <48>; >> >> hsync-len = <32>; >> >> vback-porch = <15>; >> >> vfront-porch = <3>; >> >> vsync-len = <4>; >> >> clock-frequency = <56000000>; >> >> hsync-active = <0>; >> >> vsync-active = <0>; >> >> }; >> >> }; >> >> }; >> >> >> >> fb { >> >> compatible = "ti,am33xx-tilcdc"; >> >> reg = <0x4830e000 0x1000>; >> >> interrupt-parent = <&intc>; >> >> interrupts = <36>; >> >> ti,hwmods = "lcdc"; >> >> &nbs >> ... > > -- > For more options, visit http://beagleboard.org/discuss > --- > You received this message because you are subscribed to the Google Groups > "BeagleBoard" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to beagleboard+unsubscr...@googlegroups.com. > For more options, visit https://groups.google.com/d/optout. > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to beagleboard+unsubscr...@googlegroups.com. For more options, visit https://groups.google.com/d/optout.
