Before this happened, I tried several combinations which included:
HDMI + power supply + keyboard
USB + USB TTL RS232
USB + power supply
USB + USB TTL RS232
USB + USB TTL RS232 + power supply
only power supply
and usually with the Ethernet port connected.
Now, I did check these newer releases connecting only the power supplied :
bone-debian-7.7-console-armhf-2014-12-31-2gb.img
BBB-eMMC-flasher-debian-7.7-console-armhf-2014-12-31-2gb.img
bone-debian-7.7-lxde-4gb-armhf-2014-12-31-4gb.img
BBB-eMMC-flasher-debian-7.7-lxde-armhf-2014-12-31-2gb.img
But no success, what else can I try?
----The following output appears hooking a USB-TTL serial-----
U-Boot SPL 2015.01-rc4-00002-g76c2d3b (Dec 30 2014 -
20:48:45)
U-Boot 2015.01-rc4-00002-g76c2d3b (Dec 30 2014 - 20:48:45), Build:
jenkins-gith5
Watchdog
enabled
I2C:
ready
DRAM: 512
MiB
MMC: OMAP SD/MMC: 0, OMAP SD/MMC:
1
Using default
environment
Net: <ethaddr> not set. Validating first E-fuse
MAC
Phy 0 not
found
cpsw
Hit any key to stop autoboot:
0
gpio: pin 53 (gpio 53) value is
1
switch to partitions #0,
OK
mmc0 is current
device
gpio: pin 54 (gpio 54) value is
1
Checking for: /uEnv.txt
...
reading
uEnv.txt
760 bytes read in 6 ms (123
KiB/s)
gpio: pin 55 (gpio 55) value is
1
Loaded environment from
uEnv.txt
Importing environment from mmc
...
Checking if uenvcmd is set
...
gpio: pin 56 (gpio 56) value is
1
Running uenvcmd
...
721 bytes read in 73 ms (8.8
KiB/s)
5606008 bytes read in 365 ms (14.6
MiB/s)
2868890 bytes read in 221 ms (12.4
MiB/s)
26098 bytes read in 114 ms (222.7
KiB/s)
Kernel image @ 0x82000000 [ 0x000000 - 0x558a78
]
## Flattened Device Tree blob at
88000000
Booting using the fdt blob at
0x88000000
Loading Ramdisk to 8fd43000, end 8ffff69a ...
OK
Loading Device Tree to 8fd39000, end 8fd425f1 ...
OK
Starting kernel
...
Uncompressing Linux... done, booting the
kernel.
[ 0.000000] Booting Linux on physical CPU
0x0
[ 0.000000] Initializing cgroup subsys
cpu
[ 0.000000] Linux version 3.8.13-bone68 (root@a5-imx6q-wandboard-2gb)
(gcc v4
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7),
cr=50c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
instructie
[ 0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI
AM335e
[ 0.000000] Memory policy: ECC disabled, Data cache
writeback
[ 0.000000] AM335X ES2.1 (l2cache sgx neon
)
[ 0.000000] PERCPU: Embedded 9 pages/cpu @c0d41000 s14080 r8192 d14592
u36864
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pa2
[ 0.000000] Kernel command line: console=tty0 console=ttyO0,115200n8
root=/dh
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192
bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144
bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 0.000000] __ex_table already sorted, skipping
sort
[ 0.000000] allocated 1048576 bytes of
page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want
memos
[ 0.000000] Memory: 511MB = 511MB
total
[ 0.000000] Memory: 505396k/505396k available, 18892k reserved, 0K
highmem
[ 0.000000] Virtual kernel memory
layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4
kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896
kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488
MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512
MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2
MB)
[ 0.000000] modules : 0xbf800000 - 0xbfe00000 ( 6
MB)
[ 0.000000] .text : 0xc0008000 - 0xc07f0910 (8099
kB)
[ 0.000000] .init : 0xc07f1000 - 0xc082e700 ( 246
kB)
[ 0.000000] .data : 0xc0830000 - 0xc08b7740 ( 542
kB)
[ 0.000000] .bss : 0xc08b7740 - 0xc0930f00 ( 486
kB)
[ 0.000000] Hierarchical RCU
implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to
nr_cpu_ids=1.
[ 0.000000] NR_IRQS:0 nr_irqs:0
0
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128
interrus
[ 0.000000] Total of 128 interrupts on 1 active
controller
[ 0.000000] OMAP clockevent source: GPTIMER1 at 24000000
Hz
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every
1789s
[ 0.000000] OMAP clocksource: GPTIMER2 at 24000000
Hz
[ 0.000000] Console: colour dummy device
80x30
[ 0.000000] console [tty0]
enabled
[ 0.000638] Calibrating delay loop... 993.47 BogoMIPS
(lpj=969728)
[ 0.029194] pid_max: default: 32768 minimum:
301
[ 0.029340] Security Framework
initialized
[ 0.029406] Mount-cache hash table entries:
512
[ 0.035137] Initializing cgroup subsys
cpuacct
[ 0.035183] Initializing cgroup subsys
memory
[ 0.035230] Initializing cgroup subsys
blkio
[ 0.035326] CPU: Testing write buffer coherency:
ok
[ 0.035720] CPU0: thread -1, cpu 0, socket -1, mpidr
0
[ 0.035788] Setting up static identity map for 0x804d3708 -
0x804d3754
[ 0.036728] Brought up 1
CPUs
[ 0.036757] SMP: Total of 1 processors activated (993.47
BogoMIPS).
[ 0.037561] devtmpfs:
initialized
[ 0.045903] omap_hwmod: wd_timer2: _wait_target_disable
failed
[ 0.098049] pinctrl core: initialized pinctrl
subsystem
[ 0.098202] rstctl core: initialized rstctl
subsystem
[ 0.098487] regulator-dummy: no
parameters
[ 0.098814] NET: Registered protocol family
16
[ 0.099356] DMA: preallocated 256 KiB pool for atomic coherent
allocations
[ 0.104986] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size
568
[ 0.105617] platform 49000000.edma: alias fck already
exists
[ 0.105647] platform 49000000.edma: alias fck already
exists
[ 0.105669] platform 49000000.edma: alias fck already
exists
[ 0.106386] OMAP GPIO hardware version
0.1
[ 0.108925] gpio-rctrl rstctl.4: loaded
OK
[ 0.112260] No
ATAGs?
[ 0.112283] hw-breakpoint: debug architecture 0x4
unsupported.
[ 0.113599] cpsw.0: No hwaddr in dt. Using d0:39:72:40:c6:aa from
efuse
[ 0.113637] cpsw.1: No hwaddr in dt. Using d0:39:72:40:c6:ac from
efuse
[ 0.121676] bio: create slab <bio-0> at
0
[ 0.127916] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine
driver
[ 0.128211] vmmcsd_fixed: 3300
mV
[ 0.129808] SCSI subsystem
initialized
[ 0.130060] usbcore: registered new interface driver
usbfs
[ 0.130131] usbcore: registered new interface driver
hub
[ 0.130350] usbcore: registered new device driver
usb
[ 0.131618] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400
kHz
[ 0.132552] input: tps65217_pwr_but as
/devices/ocp.3/44e0b000.i2c/i2c-0/0-00
[ 0.134173] DCDC1: at 1500
mV
[ 0.135045] vdd_mpu: 925 <--> 1325 mV at 1325
mV
[ 0.135866] vdd_core: 925 <--> 1150 mV at 1125
mV
[ 0.136727] LDO1: at 1800
mV
[ 0.137531] LDO2: at 3300
mV
[ 0.139058] LDO3: 1800
mV
[ 0.139871] LDO4: at 3300
mV
[ 0.140598] tps65217 0-0024: TPS65217 ID 0xe version
1.2
[ 0.141082] omap_i2c 44e0b000.i2c: unable to select pin
group
[ 0.141564] omap_i2c 4819c000.i2c: bus 1 rev0.11 at 100
kHz
[ 0.143036] omap_i2c 4819c000.i2c: unable to select pin
group
[ 0.143204] media: Linux media interface:
v0.10
[ 0.143275] Linux video capture interface:
v2.00
[ 0.143351] pps_core: LinuxPPS API ver. 1
registered
[ 0.143367] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo
Giom>
[ 0.143775] Advanced Linux Sound Architecture Driver
Initialized.
[ 0.144366] NetLabel:
Initializing
[ 0.144388] NetLabel: domain hash size =
128
[ 0.144470] NetLabel: protocols = UNLABELED
CIPSOv4
[ 0.144577] NetLabel: unlabeled traffic allowed by
default
[ 0.144768] Switching to clocksource
gp_timer
[ 0.176323] NET: Registered protocol family
2
[ 0.176987] TCP established hash table entries: 4096 (order: 3, 32768
bytes)
[ 0.177085] TCP bind hash table entries: 4096 (order: 4, 81920
bytes)
[ 0.177176] TCP: Hash tables configured (established 4096 bind
4096)
[ 0.177249] TCP: reno
registered
[ 0.177270] UDP hash table entries: 256 (order: 1, 12288
bytes)
[ 0.177302] UDP-Lite hash table entries: 256 (order: 1, 12288
bytes)
[ 0.177542] NET: Registered protocol family
1
[ 0.177943] RPC: Registered named UNIX socket transport
module.
[ 0.177968] RPC: Registered udp transport
module.
[ 0.177982] RPC: Registered tcp transport
module.
[ 0.177995] RPC: Registered tcp NFSv4.1 backchannel transport
module.
[ 0.178278] Trying to unpack rootfs image as
initramfs...
[ 0.372679] Freeing initrd memory:
2800K
[ 0.373021] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5
countee
[ 0.373303] CPU PMU: attempt to register multiple PMU
devices!
[ 0.373413] arm-pmu: probe of arm-pmu failed with error
-28
[ 0.373733] omap2_mbox_probe: platform not
supported
[ 0.523900] VFS: Disk quotas
dquot_6.5.2
[ 0.524065] Dquot-cache hash table entries: 1024 (order 0, 4096
bytes)
[ 0.524821] NFS: Registering the id_resolver key
type
[ 0.524930] Key type id_resolver
registered
[ 0.524945] Key type id_legacy
registered
[ 0.525215] fuse init (API version
7.20)
[ 0.525627] Btrfs
loaded
[ 0.525812] msgmni has been set to
992
[ 0.527446] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major )
[ 0.527486] io scheduler noop
registered
[ 0.527500] io scheduler deadline
registered
[ 0.527529] io scheduler cfq registered
(default)
[ 0.528746] tps65217-bl tps65217-bl: no platform data
provided
[ 0.528786] tps65217-bl: probe of tps65217-bl failed with error
-22
[ 0.529313] Serial: 8250/16550 driver, 4 ports, IRQ sharing
enabled
[ 0.530692] omap_uart 44e09000.serial: did not get pins for uart0 error:
-19
[ 0.530995] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 72) is a
OMAP U0
[ 1.290844] console [ttyO0]
enabled
[ 1.295178] [drm] Initialized drm 1.1.0
20060810
[ 1.307296] brd: module
loaded
[ 1.314228] loop: module
loaded
[ 1.317638] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1
bytes/write
[ 1.324880] at24 1-0054: 32768 byte 24c256 EEPROM, writable, 1
bytes/write
[ 1.332111] at24 1-0055: 32768 byte 24c256 EEPROM, writable, 1
bytes/write
[ 1.339351] at24 1-0056: 32768 byte 24c256 EEPROM, writable, 1
bytes/write
[ 1.346593] at24 1-0057: 32768 byte 24c256 EEPROM, writable, 1
bytes/write
[ 1.360497] bone-capemgr bone_capemgr.9: Baseboard:
'A335BNLT,00A5,5002BBBK8'
[ 1.368307] bone-capemgr bone_capemgr.9:
compatible-baseboard=ti,beaglebone-k
[ 1.406563] bone-capemgr bone_capemgr.9: slot #0: No cape
found
[ 1.443670] bone-capemgr bone_capemgr.9: slot #1: No cape
found
[ 1.480778] bone-capemgr bone_capemgr.9: slot #2: No cape
found
[ 1.517888] bone-capemgr bone_capemgr.9: slot #3: No cape
found
[ 1.524119] bone-capemgr bone_capemgr.9: slot #4: specific
override
[ 1.530702] bone-capemgr bone_capemgr.9: bone: Using override eeprom
data at4
[ 1.538734] bone-capemgr bone_capemgr.9: slot #4:
'Bone-LT-eMMC-2G,00A0,Texa'
[ 1.548829] bone-capemgr bone_capemgr.9: slot #5: specific
override
[ 1.555411] bone-capemgr bone_capemgr.9: bone: Using override eeprom
data at5
[ 1.563423] bone-capemgr bone_capemgr.9: slot #5:
'Bone-Black-HDMI,00A0,Texa'
[ 1.573404] bone-capemgr bone_capemgr.9: slot #6: specific
override
[ 1.579972] bone-capemgr bone_capemgr.9: bone: Using override eeprom
data at6
[ 1.587996] bone-capemgr bone_capemgr.9: slot #6:
'Bone-Black-HDMIN,00A0,Tex'
[ 1.598413] bone-capemgr bone_capemgr.9: loader: before slot-4
BB-BONE-EMMC-)
[ 1.607279] bone-capemgr bone_capemgr.9: loader: check slot-4
BB-BONE-EMMC-2)
[ 1.616099] bone-capemgr bone_capemgr.9: loader: before slot-5
BB-BONELT-HDM)
[ 1.624855] bone-capemgr bone_capemgr.9: loader: check slot-5
BB-BONELT-HDMI)
[ 1.633522] bone-capemgr bone_capemgr.9: initialized
OK.
[ 1.639096] bone-capemgr bone_capemgr.9: loader: before slot-6
BB-BONELT-HDM)
[ 1.647929] bone-capemgr bone_capemgr.9: loader: check slot-6
BB-BONELT-HDMI)
[ 1.658094] OneNAND driver
initializing
[ 1.663044] usbcore: registered new interface driver
cdc_ether
[ 1.669205] bone-capemgr bone_capemgr.9: loader: after slot-4
BB-BONE-EMMC-2)
[ 1.678002] usbcore: registered new interface driver
rndis_host
[ 1.684259] bone-capemgr bone_capemgr.9: loader: after slot-5
BB-BONELT-HDMI)
[ 1.692929] bone-capemgr bone_capemgr.9: loader: check slot-6
BB-BONELT-HDMI)
[ 1.701738] usbcore: registered new interface driver
cdc_ncm
[ 1.707695] bone-capemgr bone_capemgr.9: slot #4: Requesting firmware
'cape-'
[ 1.721736] usbcore: registered new interface driver
cdc_acm
[ 1.727690] cdc_acm: USB Abstract Control Model driver for USB modems
and ISs
[ 1.736076] Initializing USB Mass Storage
driver...
[ 1.741207] bone-capemgr bone_capemgr.9: slot #4: dtbo '
cape-bone-2g-emmc1.de
[ 1.751887] bone-capemgr bone_capemgr.9: slot #5: Requesting firmware
'cape-'
[ 1.766054] usbcore: registered new interface driver
usb-storage
[ 1.772345] USB Mass Storage support
registered.
[ 1.777387] bone-capemgr bone_capemgr.9: slot #4: #2
overlays
[ 1.784013] bone-capemgr bone_capemgr.9: slot #4: Applied #2
overlays.
[ 1.790895] bone-capemgr bone_capemgr.9: loader: done slot-4
BB-BONE-EMMC-2G)
[ 1.799591] bone-capemgr bone_capemgr.9: loader: check slot-6
BB-BONELT-HDMI)
[ 1.808363] bone-capemgr bone_capemgr.9: slot #5: dtbo
'cape-boneblack-hdmi-e
[ 1.819712] musb-hdrc: version 6.0, ?dma?, otg
(peripheral+host)
[ 1.826277] musb-hdrc musb-hdrc.0.auto: pdev->id =
0
[ 1.831510] musb-hdrc musb-hdrc.0.auto: drivers/usb/musb/musb_dsps.c:480
dspK
[ 1.840789] bone-capemgr bone_capemgr.9: slot #5: #4
overlays
[ 1.848265] platform 4830e000.fb: alias fck already
exists
[ 1.854242] musb-hdrc musb-hdrc.0.auto: ***
mode=3
[ 1.859304] musb-hdrc musb-hdrc.0.auto: ***
power=250
[ 1.865652] bone-capemgr bone_capemgr.9: slot #5: Applied #4
overlays.
[ 1.872518] bone-capemgr bone_capemgr.9: loader: done slot-5
BB-BONELT-HDMI:)
[ 1.881104] bone-capemgr bone_capemgr.9: loader: check slot-6
BB-BONELT-HDMI)
[ 1.890298] musb-hdrc musb-hdrc.1.auto: pdev->id =
1
[ 1.895544] musb-hdrc musb-hdrc.1.auto: drivers/usb/musb/musb_dsps.c:480
dspK
[ 1.904299] bone-capemgr bone_capemgr.9: loader: after slot-6
BB-BONELT-HDMI)
[ 1.913246] musb-hdrc musb-hdrc.1.auto: ***
mode=1
[ 1.918297] musb-hdrc musb-hdrc.1.auto: ***
power=250
[ 1.923602] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host
driver
[ 1.929656] bone-capemgr bone_capemgr.9: slot #6: Requesting firmware
'cape-'
[ 1.944163] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned
bus1
[ 1.952524] usb usb1: New USB device found, idVendor=1d6b,
idProduct=0002
[ 1.959669] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber1
[ 1.967257] usb usb1: Product: MUSB HDRC host
driver
[ 1.972450] usb usb1: Manufacturer: Linux 3.8.13-bone68
musb-hcd
[ 1.978739] usb usb1: SerialNumber:
musb-hdrc.1.auto
[ 1.983990] bone-capemgr bone_capemgr.9: slot #6: dtbo
'cape-boneblack-hdmine
[ 1.995493] bone-capemgr bone_capemgr.9: slot #6: BB-BONELT-HDMIN
conflict P)
[ 2.005087] bone-capemgr bone_capemgr.9: slot #6: Failed
verification
[ 2.011832] bone-capemgr bone_capemgr.9: loader: failed to load slot-6
BB-BO)
[ 2.022242] hub 1-0:1.0: USB hub
found
[ 2.026235] hub 1-0:1.0: 1 port
detected
[ 2.031259] mousedev: PS/2 mouse device common for all
mice
[ 2.038667] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as
rtc0
[ 2.046362] i2c /dev entries
driver
[ 2.051038] pps_ldisc: PPS line discipline
registered
[ 2.056487] Driver for 1-wire Dallas network
protocol.
[ 2.063053] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60
sec
[ 2.070732] device-mapper: ioctl: 4.23.1-ioctl (2012-12-18) initialised:
dm-m
[ 2.079624] cpuidle: using governor
ladder
[ 2.083937] cpuidle: using governor
menu
[ 2.088373] omap_hsmmc mmc.5: of_parse_phandle_with_args of 'reset'
failed
[ 2.095584] omap_hsmmc mmc.5: Failed to get rstctl; not using
any
[ 2.102259] edma-dma-engine edma-dma-engine.0: allocated channel for
0:25
[ 2.109426] edma-dma-engine edma-dma-engine.0: allocated channel for
0:24
[ 2.116694] mmc.5 supply vmmc_aux not found, using dummy
regulator
[ 2.123532] omap_hsmmc mmc.5: pins are not configured from the
driver
[ 2.156791] gpio-rctrl rstctl.4: gpio_rctrl_request
eMMC_RSTn
[ 2.162960] omap_hsmmc mmc.11: Got rstctl (gpio:#0 name eMMC_RSTn)
label:eMMn
[ 2.170937] gpio-rctrl rstctl.4: gpio_rctrl_deassert
eMMC_RSTn
[ 2.177272] edma-dma-engine edma-dma-engine.0: allocated channel for
0:3
[ 2.184369] edma-dma-engine edma-dma-engine.0: allocated channel for
0:2
[ 2.191743] mmc.11 supply vmmc_aux not found, using dummy
regulator
[ 2.198425] omap_hsmmc mmc.11: pins are not configured from the
driver
[ 2.233047] pinctrl-single 44e10800.pinmux: pin 44e10854 already
requested b8
[ 2.244715] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.8) status
-22
[ 2.252008] pinctrl-single 44e10800.pinmux: could not request pin 21 on
devie
[ 2.260953] leds-gpio gpio-leds.8: pins are not configured from the
driver
[ 2.268901] ledtrig-cpu: registered to indicate activity on
CPUs
[ 2.275467] edma-dma-engine edma-dma-engine.0: allocated channel for
0:36
[ 2.282635] omap-sham 53100000.sham: hw accel on OMAP rev
4.3
[ 2.290107] omap-aes 53500000.aes: OMAP AES hw accel rev:
3.2
[ 2.296336] edma-dma-engine edma-dma-engine.0: allocated channel for
0:5
[ 2.303496] edma-dma-engine edma-dma-engine.0: allocated channel for
0:6
[ 2.313527] usbcore: registered new interface driver
usbhid
[ 2.319450] usbhid: USB HID core
driver
[ 2.324328] ashmem:
initialized
[ 2.327740] mmc0: host does not support reading read-only switch.
assuming w.
[ 2.336479] logger: created 256K log
'log_main'
[ 2.341490] logger: created 256K log
'log_events'
[ 2.346552] mmc0: new high speed SDHC card at address
1234
[ 2.352522] logger: created 256K log
'log_radio'
[ 2.357866] mmcblk0: mmc0:1234 SA16G 14.6
GiB
[ 2.362759] logger: created 256K log
'log_system'
[ 2.369913] mmcblk0: p1
p2
[ 2.375050] davinci_evm sound.14: nxp-hdmi-hifi <-> 48038000.mcasp
mapping k
[ 2.384731] TCP: cubic
registered
[ 2.388365] NET: Registered protocol family
10
[ 2.393820] NET: Registered protocol family
17
[ 2.398854] Key type dns_resolver
registered
[ 2.403512] VFP support v0.3: implementor 41 architecture 3 part 30
variant 3
[ 2.411649] ThumbEE CPU extension
supported.
[ 2.416172] Registering SWP/SWPB emulation
handler
[ 2.421867] registered taskstats version
1
[ 2.427915] tilcdc 4830e000.fb: No power control
GPIO
[ 2.484621] mmc1: BKOPS_EN bit is not
set
[ 2.492723] mmc1: new high speed MMC card at address
0001
[ 2.498967] mmcblk1: mmc1:0001 MMC04G 3.60
GiB
[ 2.503978] mmcblk1boot0: mmc1:0001 MMC04G partition 1 2.00
MiB
[ 2.510392] mmcblk1boot1: mmc1:0001 MMC04G partition 2 2.00
MiB
[ 2.517660] mmcblk1: p1
p2
[ 2.522285] mmcblk1boot1: unknown partition
table
[ 2.528630] mmcblk1boot0: unknown partition
table
[ 2.553552] tilcdc 4830e000.fb: found
TDA19988
[ 2.558808] [drm] Supports vblank timestamp caching Rev 1
(10.10.2010).
[ 2.565737] [drm] No driver support for vblank timestamp
query.
[ 2.572217] tilcdc 4830e000.fb: No connectors reported connected with
modes
[ 2.579524] [drm] Cannot find any crtc or sizes - going
1024x768
[ 2.595082] Console: switching to colour frame buffer device
128x48
[ 2.607780] tilcdc 4830e000.fb: fb0: frame buffer
device
[ 2.613497] tilcdc 4830e000.fb: registered panic
notifier
[ 2.619238] [drm] Initialized tilcdc 1.0.0 20121205 on minor
0
[ 2.674157] davinci_mdio 4a101000.mdio: davinci mdio revision
1.6
[ 2.680651] davinci_mdio 4a101000.mdio: no live phy, scanning
all
[ 2.687348] davinci_mdio: probe of 4a101000.mdio failed with error
-5
[ 2.694428] Detected MACID =
d0:39:72:40:c6:aa
[ 2.699039] Unhandled fault: external abort on non-linefetch (0x1008) at
0xe0
[ 2.707366] Internal error: : 1008 [#1] SMP
THUMB2
[ 2.712451] Modules linked
in:
[ 2.715705] CPU: 0 Not tainted (3.8.13-bone68
#1)
[ 2.721078] PC is at
cpsw_probe+0x348/0x960
[ 2.725523] LR is at
ioremap_page_range+0x95/0xf8
[ 2.732827] pc : [<c032552c>] lr : [<c0255c75>] psr:
a0000033
[ 2.732827] sp : df071e18 ip : 00000000 fp :
df0d3400
[ 2.749501] r10: c082ab94 r9 : de5f9800 r8 :
de5f9d90
[ 2.757301] r7 : de5f9800 r6 : de5f9d40 r5 : 00000000 r4 :
e089c000
[ 2.766457] r3 : 80000000 r2 : 00000000 r1 : e089d000 r0 :
e089c000
[ 2.775568] Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA Thumb
Segment kl
[ 2.785724] Control: 50c5387d Table: 9e268019 DAC:
00000015
[ 2.794081] Process swapper/0 (pid: 1, stack limit =
0xdf070240)
[ 2.802772] Stack: (0xdf071e18 to
0xdf072000)
[ 2.809738] 1e00:
00009
[ 2.820732] 1e20: c0877bb8 c0877bb8 de5f9d40 de5f9a98 df0d3410 de5fc8c8
00000
[ 2.831706] 1e40: df071e90 c00ff1b3 22222222 22222222 00000000 c0877bb8
de5f0
[ 2.842700] 1e60: de5fc8c8 c00ff0ef de5fc8c8 00000000 df071e90 de5fc948
df0d7
[ 2.853720] 1e80: df0494b8 c0049697 00000000 df0d3444 00000020 00000008
df0dc
[ 2.864765] 1ea0: df0d3410 c0896c40 00000000 c080d039 00000100 c082ab94
00009
[ 2.875832] 1ec0: c02c8269 c02c771b 00000000 df0d3410 c0896c40 df0d3444
0000b
[ 2.886905] 1ee0: c0896c40 c02c7831 00000000 c02c684f df049478 df0c4180
c0890
[ 2.897970] 1f00: de262340 c02c720f c073906c c0896c40 c0896c40 df070000
c08b0
[ 2.909049] 1f20: c080d039 c02c7b7d 00000000 c08177b0 df070000 c08b7740
00009
[ 2.920145] 1f40: 00000100 c000867f 00000007 00000007 c086fc98 c08177ac
c0817
[ 2.931294] 1f60: c0817790 c08b7740 c07f11c9 c082ab94 00000000 c07f16a3
00007
[ 2.942468] 1f80: c07f11c9 c0d43fc0 00000000 c04c61c9 00000000 00000000
00000
[ 2.953645] 1fa0: 00000000 c04c61cf 00000000 c000c8fd 00000000 00000000
00000
[ 2.964832] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000
00000
[ 2.976004] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000
00000
[ 2.987136] [<c032552c>] (cpsw_probe+0x348/0x960) from [<c02c8279>]
(platfor)
[ 2.999120] [<c02c8279>] (platform_drv_probe+0x11/0x14) from
[<c02c771b>] (d)
[ 3.011838] [<c02c771b>] (driver_probe_device+0x53/0x168) from
[<c02c787b>] )
[ 3.024334] [<c02c787b>] (__driver_attach+0x4b/0x4c) from [<c02c684f>]
(bus_)
[ 3.036481] [<c02c684f>] (bus_for_each_dev+0x27/0x48) from [<c02c720f>]
(bus)
[ 3.048653] [<c02c720f>] (bus_add_driver+0xe3/0x168) from [<c02c7b7d>]
(driv)
[ 3.060781] [<c02c7b7d>] (driver_register+0x3d/0xc4) from [<c000867f>]
(do_o)
[ 3.072901] [<c000867f>] (do_one_initcall+0x1f/0xf4) from [<c07f16a3>]
(kern)
[ 3.085602] [<c07f16a3>] (kernel_init_freeable+0xc3/0x158) from
[<c04c61cf>])
[ 3.097886] [<c04c61cf>] (kernel_init+0x7/0x98) from [<c000c8fd>]
(ret_from_)
[ 3.109458] Code: f000 81d2 f8c7 05c0 (6803)
f44f
[ 3.117292] ---[ end trace 827194fc7d813ac2
]---
[ 3.125125] Kernel panic - not syncing: Attempted to kill init!
exitcode=0x0b
[
3.125125]
[ 3.140302] drm_kms_helper: panic occurred, switching back to text
console
2015-01-16 14:17 GMT-06:00 Robert Nelson <robertcnel...@gmail.com>:
> On Fri, Jan 16, 2015 at 12:24 PM, Arturo Gómez <arturo.goo...@gmail.com>
> wrote:
> >
> > Thank you for your prompt response.
> > I have tried plugging only a Power supply of 5v/2.4A with the same
> problem.
> > The sequence of LEDS start blinking but abruptly only the User LED 2
> remains
> > on.
>
> Umm.. What "else" did you have plugged in?
>
>
> > The releases tested:
> >
> Angstrom-Cloud9-IDE-GNOME-eglibc-ipk-v2012.12-beaglebone-2013.06.20.img.xz
> > BBB-eMMC-flasher-2013.09.04.img.xz
> > BBB-eMMC-flasher-debian-7.5-2014-05-14-2gb.img.xz
> > bone-debian-7.5-2014-05-14-2gb.img.xz
> > kali-1.0.9-bbb.img.xz
>
> Everything old..
>
> Give the latest snapshot a try:
>
> http://elinux.org/Beagleboard:BeagleBoneBlack_Debian#2014-12-31
>
> Regards,
>
> --
> Robert Nelson
> http://www.rcn-ee.com/
>
> --
> For more options, visit http://beagleboard.org/discuss
> ---
> You received this message because you are subscribed to a topic in the
> Google Groups "BeagleBoard" group.
> To unsubscribe from this topic, visit
> https://groups.google.com/d/topic/beagleboard/gyzQu1ZIiBo/unsubscribe.
> To unsubscribe from this group and all its topics, send an email to
> beagleboard+unsubscr...@googlegroups.com.
> For more options, visit https://groups.google.com/d/optout.
>
--
For more options, visit http://beagleboard.org/discuss
---
You received this message because you are subscribed to the Google Groups
"BeagleBoard" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to beagleboard+unsubscr...@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
