Hi, Thank you so much for your response.
How do you say, the issue is because of firmware only. Thanks Madhu On Sat, Aug 12, 2017 at 1:37 PM, Mala Dies <fun...@gmail.com> wrote: > Hello, > > You might have to update the firmware on your WiFi dongle. > > Seth > > > On Wednesday, August 9, 2017 at 1:08:28 AM UTC-5, Madhu K wrote: >> >> Hi All, >> >> I was trying to configure wifi on beaglebone black board. But i am facing >> below problems. >> >> I am using TP-LINK TL-WN823N adaptor. >> >> Beaglebone black wifi setup steps : >> >> 1) Downloaded the stable kernel 4.4.2 from git. >> 2) Compiled the kernel and loaded new kernel to beaglebone black. >> 3) Downloaded the rlt8192eu ( TL-WN823N ) driver code from git. >> 4) Compiled the driver code for beaglebone black and inserted the module >> to new kernel. >> 5) Inserted TL-WN823N adapter to beaglebone black. >> >> Problems : >> >> 1) I am getting below messages, i don't know what exactly that message >> indicates. >> >> [ 361.376724] RTL871X: Wrong rate section: (CCK,2T) >> [ 361.381816] RTL871X: Wrong rate section: (CCK,2T) >> >> >> >> [ 361.810547] RTL871X: duplicate tx power limit combination [band >> 2.4G][regulation ETSI][bw 20M][rate section HT][rf path 2T][chnl 01] >> [ 361.823118] RTL871X: duplicate tx power limit combination [band >> 2.4G][regulation MKK][bw 20M][rate section HT][rf path 2T][chnl 01] >> [ 361.835593] RTL871X: duplicate tx power limit combination [band >> 2.4G][regulation FCC][bw 20M][rate section HT][rf path 2T][chnl 02] >> >> >> 2) I could see the wlan0 in ifconfig. but there no ip for wlano. I >> executed sudo ifup wlan0 command and i am getting below messages. >> >> >> DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 3 >> (xid=0x1e59e38c) >> [ 840.120795] RTL871X: nolinked power save enter >> DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 6 >> (xid=0x1e59e38c) >> [ 846.819487] RTL871X: nolinked power save leave >> DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 19 >> (xid=0x1e59e38c) >> [ 848.471030] RTL871X: nolinked power save enter >> [ 855.165440] RTL871X: nolinked power save leave >> [ 856.821011] RTL871X: nolinked power save enter >> >> >> please help to resolve these issue. >> >> >> Thanks and regards, >> >> Madhu > > -- > For more options, visit http://beagleboard.org/discuss > --- > You received this message because you are subscribed to the Google Groups > "BeagleBoard" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to beagleboard+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/beagleboard/288d3873-4569-4428-9351-f0b50b5739eb%40googlegroups.com. > > For more options, visit https://groups.google.com/d/optout. -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to beagleboard+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/CAA2oCOnZZSQ3MM7RhExUQUDTgx9x_crqYeO7AyaVk11Wd3Ok-w%40mail.gmail.com. For more options, visit https://groups.google.com/d/optout.