It works fine on the PocketBeagle running Debian. You do need to connect it to USB1, which is pinned out on the accessory connectors, and not USB0, which is on the micro-USB connector. --- Graham
== On Thu, Feb 15, 2018 at 7:04 AM, <cyril.jourdan...@gmail.com> wrote: > Hello, > > I'm trying to get Internet over USB working on the PocketBeagle with an > Ubuntu 16.04 host, but without success. > Has anybody managed to get that working ? > > Thanks! > > Le mardi 19 décembre 2017 18:15:37 UTC+1, Jason Kridner a écrit : >> >> >> >> On Tuesday, October 3, 2017 at 10:58:51 PM UTC-4, Graham wrote: >>> >>> Andy: >>> >>> The following is an outline of what to do to connect a PocketBeagle to >>> the internet via the USB cable to a Windows 10 desktop which is connected >>> to the Internet via hardwire Ethernet. >>> >>> ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ >>> Ethernet over USB Tether Gadget >>> ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ >>> >>> This is to connect a PocketBeagle to the Internet through the USB >>> connection to a Windows 10 desktop, which is connected by hardwire Ethernet >>> to the Internet. >>> >>> I used 'Etcher' to load a fresh copy of the latest 'stretch' version of >>> Debian 9.1 onto the Pocketbone. >>> bone-debian-9.1-iot-armhf-2017-10-01-4gb.img >>> >>> Plug the PocketBeagle into an open USB port on your Windows 10 desktop >>> >>> The four LEDs should start blinking, and after about a minute or so, a >>> new USB serial device should appear in Device Manager\Ports(COM&LPT), and a >>> new Remote NDIS Compatible Device should appear in Device Manager\Network >>> Adaptors >>> >>> Also, a new Ethernet interface will appear in Control Panel\Network and >>> Internet\Network Connections. >>> It will be described as "Unidentified Network", Remote NDIS Compatible >>> Device >>> >>> Use Putty to connect to the new COM port >>> log into the PocketBeagle >>> >>> now type >>> sudo /sbin/route add default gw 192.168.7.1 >>> >> >> Instead of doing this, I use 'sudo dhclient usb0' such that it updates >> the nameservers (/etc/resolv.conf) automatically. >> >> For Mac/Linux, I use 'sudo dhclient usb1'. >> >> >>> >>> Now, on the Windows 10 desktop, >>> go to and open your primary Ethernet interface: >>> Ethernet\Properties\Sharing\ >>> Check the two sharing boxes. >>> Enter the name of the new NDIS Device interface into the box. [In my >>> case it was Ethernet 2 ] >>> Click 'OK' and exit the interface box >>> >>> Now open the Unidentified Network\NDIS Device >>> interface\Properties\Internet Protocol Version 4\Properties >>> Click 'Use the following IP address' >>> Enter 192.168.7.1 as the IP address >>> Enter 255.255.255.0 as the Subnet Mask >>> >>> Click 'Use the following DNS server addresses' >>> Enter 8.8.8.8 as the Preferred DNS server. >>> Click 'OK' and 'Close' to exit >>> >>> Now go to the PocketBeagle command line on Putty >>> sudo nano /etc/resolv.conf >>> down-arrow to get past the comment line >>> enter 'nameserver 8.8.8.8' [without the quotes] >>> enter <return> >>> enter <control-X>, then 'Y', <return> to exit [without the quotes] >>> >>> The Ethernet tether gadget should be operational. >>> To test, type 'ping google.com' in the command line. [without the >>> quotes] >>> It should run and see the ping replies. >>> type <control-c> to abort. >>> >>> You should now have internet access and can >>> sudo apt-get update >>> >>> The two entries in the PockBeagle are not persistent, so after any >>> reboot, >>> you will have to repeat the two entries in the PocketBeagle to get the >>> internet tether gadget running again. >>> >>> >>> There is more information here ... >>> https://www.digikey.com/en/maker/blogs/how-to-connect-a-beag >>> lebone-black-to-the-internet-using-usb/cdf66181b3a5436e9ad730e4ed4cf9ee >>> >>> == >>> >> > -- > For more options, visit http://beagleboard.org/discuss > --- > You received this message because you are subscribed to a topic in the > Google Groups "BeagleBoard" group. > To unsubscribe from this topic, visit https://groups.google.com/d/ > topic/beagleboard/JtOGZb-FH2A/unsubscribe. > To unsubscribe from this group and all its topics, send an email to > beagleboard+unsubscr...@googlegroups.com. > To view this discussion on the web visit https://groups.google.com/d/ > msgid/beagleboard/b1129fa8-22ef-49ba-9237-11c5586ef8a5%40googlegroups.com > <https://groups.google.com/d/msgid/beagleboard/b1129fa8-22ef-49ba-9237-11c5586ef8a5%40googlegroups.com?utm_medium=email&utm_source=footer> > . > For more options, visit https://groups.google.com/d/optout. > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to beagleboard+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/CANN_KV5TZ6Gpegs05n4aaKA7Cun7jwPhQ9tm1mVNv_-h8DQ62w%40mail.gmail.com. For more options, visit https://groups.google.com/d/optout.
