thank!, I do the cmd but now the linux is not booting this is the serial log
> U-Boot SPL 2018.01-00002-g9aa111a004 (Jan 20 2018 - 12:45:29) > > Trying to boot from MMC1 > > >> >> U-Boot 2018.01-00002-g9aa111a004 (Jan 20 2018 - 12:45:29 -0600), Build: >> jenkins-github_Bootloader-Builder-32 > > >> CPU : AM335X-GP rev 2.1 > > I2C: ready > > DRAM: 512 MiB > > No match for driver 'omap_hsmmc' > > No match for driver 'omap_hsmmc' > > Some drivers were not found > > Reset Source: Power-on reset has occurred. > > MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 > > Using default environment > > >> Board: BeagleBone Black > > <ethaddr> not set. Validating first E-fuse MAC > > BeagleBone Black: > > Model: SeeedStudio BeagleBone Green Wireless: > > BeagleBone: cape eeprom: i2c_probe: 0x54: > > BeagleBone: cape eeprom: i2c_probe: 0x55: > > BeagleBone: cape eeprom: i2c_probe: 0x56: > > BeagleBone: cape eeprom: i2c_probe: 0x57: > > Net: eth0: MII MODE > > Could not get PHY for cpsw: addr 0 > > cpsw, usb_ether > > Press SPACE to abort autoboot in 2 seconds > > board_name=[A335BNLT] ... > > board_rev=[GW1A] ... > > switch to partitions #0, OK > > mmc0 is current device > > SD/MMC found on device 0 > > ** Bad device 0:2 0x82000000 ** > > ** Bad device 0:2 0x82000000 ** > > switch to partitions #0, OK > > mmc0 is current device > > Scanning mmc 0:1... > > gpio: pin 56 (gpio 56) value is 0 > > gpio: pin 55 (gpio 55) value is 0 > > gpio: pin 54 (gpio 54) value is 0 > > gpio: pin 53 (gpio 53) value is 1 > > switch to partitions #0, OK > > mmc0 is current device > > gpio: pin 54 (gpio 54) value is 1 > > Checking for: /uEnv.txt ... > > Checking for: /boot.scr ... > > Checking for: /boot/boot.scr ... > > Checking for: /boot/uEnv.txt ... > > gpio: pin 55 (gpio 55) value is 1 > > 1867 bytes read in 43 ms (42 KiB/s) > > Loaded environment from /boot/uEnv.txt > > Checking if uname_r is set in /boot/uEnv.txt... > > gpio: pin 56 (gpio 56) value is 1 > > Running uname_boot ... > > loading /boot/vmlinuz-4.4.125-bone22 ... > > 8506344 bytes read in 587 ms (13.8 MiB/s) > > uboot_overlays: [uboot_base_dtb=am335x-boneblack-uboot.dtb] ... > > uboot_overlays: Switching too: dtb=am335x-boneblack-uboot.dtb ... > > loading /boot/dtbs/4.4.125-bone22/am335x-boneblack-uboot.dtb ... > > 50339 bytes read in 79 ms (622.1 KiB/s) > > uboot_overlays: [fdt_buffer=0x60000] ... > > uboot_overlays: loading /lib/firmware/BB-BONE-eMMC1-01-00A0.dtbo ... > > 1440 bytes read in 179 ms (7.8 KiB/s) > > uboot_overlays: loading /lib/firmware/BB-BBGW-WL1835-00A0.dtbo ... > > 4839 bytes read in 69 ms (68.4 KiB/s) > > failed on fdt_overlay_apply(): FDT_ERR_NOTFOUND > > uboot_overlays: loading /lib/firmware/BB-ADC-00A0.dtbo ... > > 711 bytes read in 219 ms (2.9 KiB/s) > > libfdt fdt_check_header(): FDT_ERR_BADMAGIC > > failed on fdt_overlay_apply(): FDT_ERR_BADMAGIC > > base fdt does did not have a /__symbols__ node > > make sure you've compiled with -@ > > uboot_overlays: loading /lib/firmware/AM335X-PRU-UIO-00A0.dtbo ... > > 883 bytes read in 162 ms (4.9 KiB/s) > > libfdt fdt_check_header(): FDT_ERR_BADMAGIC > > failed on fdt_overlay_apply(): FDT_ERR_BADMAGIC > > base fdt does did not have a /__symbols__ node > > make sure you've compiled with -@ > > uboot_overlays: loading /lib/firmware/univ-bbgw-EW-00A0.dtbo ... > > 82622 bytes read in 89 ms (906.3 KiB/s) > > libfdt fdt_check_header(): FDT_ERR_BADMAGIC > > failed on fdt_overlay_apply(): FDT_ERR_BADMAGIC > > base fdt does did not have a /__symbols__ node > > make sure you've compiled with -@ > > loading /boot/initrd.img-4.4.125-bone22 ... > > 5415890 bytes read in 392 ms (13.2 MiB/s) > > debug: [console=ttyO0,115200n8 bone_capemgr.uboot_capemgr_enabled=1 >> root=/dev/mmcblk0p1 ro rootfstype=ext4 rootwait coherent_pool=1M >> net.ifnames=0 quiet] ... > > debug: [bootz 0x82000000 0x88080000:52a3d2 88000000] ... > > ERROR: Did not find a cmdline Flattened Device Tree > > Could not find a valid device tree > > ** Invalid partition 2 ** > > ** Invalid partition 3 ** > > ** Invalid partition 4 ** > > ** Invalid partition 5 ** > > ** Invalid partition 6 ** > > ** Invalid partition 7 ** > > switch to partitions #0, OK > > mmc1(part 0) is current device > > ** No partition table - mmc 1 ** > > gpio: pin 56 (gpio 56) value is 0 > > gpio: pin 55 (gpio 55) value is 0 > > gpio: pin 54 (gpio 54) value is 0 > > gpio: pin 53 (gpio 53) value is 1 > > switch to partitions #0, OK > > mmc1(part 0) is current device > > gpio: pin 54 (gpio 54) value is 1 > > ** No partition table - mmc 1 ** > > Checking for: /uEnv.txt ... > > ** No partition table - mmc 1 ** > > Checking for: /boot.scr ... > > ** No partition table - mmc 1 ** > > Checking for: /boot/boot.scr ... > > ** No partition table - mmc 1 ** > > Checking for: /boot/uEnv.txt ... > > ** No partition table - mmc 1 ** > > ** No partition table - mmc 1 ** > > ** No partition table - mmc 1 ** > > ** No partition table - mmc 1 ** > > ** No partition table - mmc 1 ** > > ** No partition table - mmc 1 ** > > ** No partition table - mmc 1 ** > > starting USB... > > USB0: scanning bus 0 for devices... 1 USB Device(s) found > > scanning usb for storage devices... 0 Storage Device(s) found > > using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in > > MAC b0:d5:cc:71:f8:50 > > HOST MAC de:ad:be:af:00:00 > > RNDIS ready > > musb-hdrc: peripheral reset irq lost! > > high speed config #2: 2 mA, Ethernet Gadget, using RNDIS > > The remote end did not respond in time.missing environment variable: >> pxeuuid > > Retrieving file: pxelinux.cfg/01-b0-d5-cc-71-f8-50 > > using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in > > MAC b0:d5:cc:71:f8:50 > > HOST MAC de:ad:be:af:00:00 > > RNDIS ready > > high speed config #2: 2 mA, Ethernet Gadget, using RNDIS > > The remote end did not respond in time.Retrieving file: >> pxelinux.cfg/C0A80102 > > using musb-hdrc, OUT ep1out IN ep1in STATUS ep2in > > MAC b0:d5:cc:71:f8:50 > > HOST MAC de:ad:be:af:00:00 > > RNDIS ready > > high speed config #2: 2 mA, Ethernet Gadget, using RNDIS > > >> On Tuesday, April 3, 2018 at 7:05:12 PM UTC-3, RobertCNelson wrote: > > On Tue, Apr 3, 2018 at 4:59 PM, Sebastián Sáez <otr...@gmail.com > <javascript:>> wrote: > > Hi!, > > > > I'm follow this tutorial, but I can't enable the PRU output > > http://jkuhlm.bplaced.net/beaglebone-433mhz-transmitter/ > > > >> root@beaglebone:~/rfsend# config-pin p8.11 pruout > >> P8_11 pinmux file not found! > >> Pin has no cape: P8_11 > > > > > > After some research in the forum I think maybe it's a problem with the > > kernel version, but I have no clue > > > > In /boot/uEnv.txt this is line is uncomment > > uboot_overlay_pru=/lib/firmware/AM335X-PRU-UIO-00A0.dtbo > > > > > > This is my system (beaglebone green wireless) > >> > >> sudo /opt/scripts/tools/version.sh > >> git:/opt/scripts/:[70edebd65fe6ea7de16ea8efe3c48b2a4062034a] > >> eeprom:[A335BNLTGW1ABBGW16050761] > >> model:[TI_AM335x_BeagleBone_Green_Wireless] > >> dogtag:[BeagleBoard.org Debian Image 2018-02-01] > >> bootloader:[microSD-(push-button)]:[/dev/mmcblk0]:[U-Boot > >> 2018.01-00002-g9aa111a004]:[location: dd MBR] > > >> bootloader:[eMMC-(default)]:[/dev/mmcblk1]:[U-Boot > >> 2017.03-00002-gd12b1519b4]:[location: dd MBR] > > The old version of u-boot in the eMMC is blocking u-boot overlays from > working correctly.. > > sudo dd if=/dev/zero of=/dev/mmcblk1 bs=1M count=10 > > Then reboot and it'll work just fine.. > > Regards, > > -- > Robert Nelson > https://rcn-ee.com/ > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to beagleboard+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/573f7526-a61b-44cf-85e0-52be69761cd8%40googlegroups.com. For more options, visit https://groups.google.com/d/optout.