john@Pandora:~$ ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth3: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast
state DOWN group default qlen 1000
link/ether 14:cc:20:05:f2:1c brd ff:ff:ff:ff:ff:ff
inet 192.168.10.1/24 brd 192.168.10.255 scope global eth3
valid_lft forever preferred_lft forever
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP
group default qlen 1000
link/ether d4:ae:52:cc:87:bb brd ff:ff:ff:ff:ff:ff
inet 192.168.0.100/24 brd 192.168.0.255 scope global eth0
valid_lft forever preferred_lft forever
inet6 fe80::d6ae:52ff:fecc:87bb/64 scope link
valid_lft forever preferred_lft forever
4: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group
default qlen 1000
link/ether 90:e2:ba:4c:54:b8 brd ff:ff:ff:ff:ff:ff
5: eth2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group
default qlen 1000
link/ether 90:e2:ba:4c:54:b9 brd ff:ff:ff:ff:ff:ff
john@Pandora:~$ ip route
default via 192.168.0.1 dev eth0
192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.100
192.168.10.0/24 dev eth3 proto kernel scope link src 192.168.10.1
john@Pandora:~$ sudo service isc-dhcp-server restart
john@Pandora:~$ sudo tail -f /var/log/syslog
...
Jul 21 08:06:13 Pandora kernel: [71959.936774] init: isc-dhcp-server
main process (1293) killed by TERM signal
Jul 21 08:06:13 Pandora dhcpd: Not searching LDAP since ldap-server,
ldap-port and ldap-base-dn were not specified in the config file
Jul 21 08:06:13 Pandora dhcpd: Not searching LDAP since ldap-server,
ldap-port and ldap-base-dn were not specified in the config file
Jul 21 08:06:13 Pandora dhcpd: Wrote 0 leases to leases file.
Den 21. juli 2015 02:49, skrev John Hearns:
John
Please give is the results of ‘ip addr’
Also look closely at the system log messages when dhcp starts.
Stop the dhcp service, then restart it when running a tail –f on the
system log.
If that does not help, stop the dhcp service and run dhcpd with the
‘-d’ flag in a separate window,
and give it the argument eth3 on the command line ?
_______________________________________________
Beowulf mailing list, [email protected] sponsored by Penguin Computing
To change your subscription (digest mode or unsubscribe) visit
http://www.beowulf.org/mailman/listinfo/beowulf
