Two blades would sure help the balance problem. Mine has only one blade. I have cut many holes with it, however using a hand drill. It's a bit challenging, but can be done. A little scary when you're doing something like cutting a hole in a door to install a lock set since you only have one shot to get it right!
Darrin Darrin Porter Senior Technical Engineer United Ocean Services, L.L.C. 601 South Harbour Island Boulevard, Suite 230 Tampa, Florida 33602 (813) 209-4247 (office) (813) 744-0011 (cellular phone) (813) 242-4849 (fax) darrin.por...@united-mar.comm<mailto:darrin.por...@united-mar.comm> ________________________________ From: blindhandyman@yahoogroups.com [mailto:blindhandy...@yahoogroups.com] On Behalf Of Spiro Sent: Wednesday, August 05, 2009 8:27 PM To: blindhandyman@yahoogroups.com Subject: RE: [BlindHandyMan] Desk Grommets & Hole Saws they make these with 2 spinning blades. They are available several places, I got mine at McMaster Carr supply. They say these things are only good for drill presses as they are challenging. I've often used it to *draw my hole and then I've used either a sabersaw (4 inch or bigger) or a router to cut away the material when I didn't want to go through with the spinners. On Tue, 4 Aug 2009, Darrin Porter wrote: > A couple of thoughts and a suggestion: > > Measure the actual size of the hole you cut to see how close to one inch it > really is. If you were doing it with a hand drill as apposed to a drill > press, the vibration of the tool and your inability to hold the drill > perfectly vertical and still may have wallowed out the hole a little. > > Measure the grommet to see how close to one inch the OD really is. > > My only suggestion is to buy a "circle cutter." I got mine from Sears about > twenty years ago. I assume they still sell them. > > If you're not familiar with this tool, it is similar to a hole saw. It has a > pilot bit that drills about a quarter-inch hole in the center of the circle. > But, instead of having a round saw that actually cuts the hole, it has an > adhjustable blade so you can make any size hole you want.. The chief drawback > is that it is difficult to control if you don't have strong hands, since you > are essentially spinning, at high speed, an off-center load. The pilot bit > helps steady it, but it still takes a bit of getting used to. > > Darrin > > > Darrin Porter > Senior Technical Engineer > > > United Ocean Services, L.L.C. > 601 South Harbour Island Boulevard, Suite 230 > Tampa, Florida 33602 > (813) 209-4247 (office) > (813) 744-0011 (cellular phone) > (813) 242-4849 (fax) > darrin.por...@united-mar.comm<mailto:DARRIN.PORTER%40UNITED-MAR.COMM><mailto:darrin.por...@united-mar.comm<mailto:DARRIN.PORTER%40UNITED-MAR.COMM>> > > ________________________________ > From: blindhandyman@yahoogroups.com<mailto:blindhandyman%40yahoogroups.com> > [mailto:blindhandyman@yahoogroups.com<mailto:blindhandyman%40yahoogroups.com>] > On Behalf Of Bill Gallik > Sent: Monday, August 03, 2009 9:25 PM > To: Blind Handy Man > Subject: [BlindHandyMan] Desk Grommets & Hole Saws > > > > Can anybody explain why the hole saws I've used (1", 2" & 3") do not cut a > hole that snugly fits the (1", 2" & 3") desk grommets I purchased from > Menard's? What I wound up with was a hole just slightly larger than the > indicated size of the corresponding grommet. Yet, if I drop down to the > next smaller size (7/8") the 1" grommet cannot fit into the resulting hole. > Can anybody explain what is to be done to end up with a hole that snugly > holds the desk grommet? > ---*---*---*---*---*---*--- > Holland's Person, Bill > E-Mail: > billgal...@centurytel.net<mailto:BillGallik%40CenturyTel.net><mailto:BillGallik%40CenturyTel.net> > - Anonymous (from my source of goofy stuff) > - Eggs and Bacon for Breakfast > - An entire day commitment for a chicken. > - A Lifetime Commitment for a Pig > > > ________________________________ > Attention: This email and any accompanying attachments constitute > confidential and/or legally privileged information. If you have received this > email communication in error, please notify the sender immediately and delete > the message and any attachments from your system. > > > [Non-text portions of this message have been removed] > > ________________________________ Attention: This email and any accompanying attachments constitute confidential and/or legally privileged information. If you have received this email communication in error, please notify the sender immediately and delete the message and any attachments from your system. [Non-text portions of this message have been removed]