Richard Sent <rich...@freakingpenguin.com> writes: > Hi Guix! > > When generating a VisionFive2 system image via $ guix system image > gnu/system/images/visionfive2.scm --no-grafts --target=riscv64-linux-gnu > and attempting to boot from MMC2, the SD card U-boot fails to boot > Linux. > > (Pretty sure --target= is gratuitous but I kept it.) > > This occurs despite setting and saving the ftdfile variable as described > in the instructions: > > --8<---------------cut here---------------start------------->8--- > ;;; Commentary: > ;;; > ;;; VisionFive2 can boot from MMC1 (SPI flash) or MMC2 (SD card) selected > ;;; by DIP switches MSEL[1:0], you may want boot from MMC2 to use the > ;;; U-Boot from Guix System instead of the vendor U-Boot in MMC1. Before > ;;; doing so, make sure you have a correct 'fdtfile' in the environment: > ;;; > ;;; uboot> setenv fdtfile starfive/jh7110-starfive-visionfive-2-v1.3b.dtb > ;;; uboot> saveenv > --8<---------------cut here---------------end--------------->8--- > > --8<---------------cut here---------------start------------->8--- > # Confirming the variable is set after reboot using the U-boot console: > StarFive # printenv fdtfile > fdtfile=starfive/jh7110-starfive-visionfive-2-v1.3b.dtb > --8<---------------cut here---------------end--------------->8---
hello!, can you try boot from mmc1, and do setenv and saveenv on mmc1 uboot, then reset and boot from mmc2? > > The system /does/ boot into Linux if SPI Flash is selected as a boot > source, although since the onboard bootloader is outdated the system > only sees 4 GiB of RAM [1]. > > Attached is the full failing boot log. Here are the highlights: > > --8<---------------cut here---------------start------------->8--- > U-Boot SPL 2024.01 (Jan 01 1970 - 00:00:01 +0000) > DDR version: dc2e84f0. > Trying to boot from MMC2 > > OpenSBI v1.3 > > ################ SNIP ################ > > U-Boot 2024.01 (Jan 01 1970 - 00:00:01 +0000) > > CPU: rv64imafdc_zba_zbb > Model: StarFive VisionFive 2 v1.3B > DRAM: 8 GiB > Core: 134 devices, 26 uclasses, devicetree: board > WDT: Not starting watchdog@13070000 > MMC: mmc@16010000: 0, mmc@16020000: 1 > Loading Environment from SPIFlash... SF: Detected gd25lq128 with page size > 256 Bytes, erase size 4 KiB, total 16 MiB > OK > StarFive EEPROM format v2 > > ################ SNIP ################ > > starfive_7110_pcie pcie@2b000000: Starfive PCIe bus probed. > starfive_7110_pcie pcie@2c000000: Starfive PCIe bus probed. > In: serial@10000000 > Out: serial@10000000 > Err: serial@10000000 > Net: eth0: ethernet@16030000, eth1: ethernet@16040000 > libfdt fdt_check_header(): FDT_ERR_BADMAGIC > Card did not respond to voltage select! : -110 > Card did not respond to voltage select! : -110 > bootmode flash device 0 > Card did not respond to voltage select! : -110 > Hit any key to stop autoboot: 0 > Card did not respond to voltage select! : -110 > ** Bad device specification mmc 0 ** > Couldn't find partition mmc 0:3 > Can't set block device > Importing environment from mmc0 ... > ## Warning: Input data exceeds 1048576 bytes - truncated > ## Info: input data size = 1048578 = 0x100002 > Can't set block device > ## Warning: defaulting to text format > ## Error: "boot2" not defined > Card did not respond to voltage select! : -110 > ethernet@16030000 Waiting for PHY auto negotiation to complete......... > TIMEOUT ! > phy_startup() failed: -110FAILED: -110ethernet@16040000 Waiting for PHY auto > negotiation to complete......... TIMEOUT ! > phy_startup() failed: -110FAILED: -110ethernet@16030000 Waiting for PHY auto > negotiation to complete......... TIMEOUT ! > phy_startup() failed: -110FAILED: -110ethernet@16040000 Waiting for PHY auto > negotiation to complete......... TIMEOUT ! > phy_startup() failed: -110FAILED: -110StarFive # > StarFive # > --8<---------------cut here---------------end--------------->8--- > > Guix Describe: > > --8<---------------cut here---------------start------------->8--- > Generation 77 May 24 2024 00:15:41 (current) > guix 9901416 > repository URL: https://git.savannah.gnu.org/git/guix.git > branch: master > commit: 9901416233867233192b63fde7f616751127b189 > --8<---------------cut here---------------end--------------->8--- > > [2. VisionFive2 U-boot failure --- text/plain; > visionfive2-u-boot-failure.log]... > > > [1]: https://github.com/starfive-tech/VisionFive2/issues/20
signature.asc
Description: PGP signature
