Hi, nobody out there who has simular problems? Here some more informations: parted version: 1.7.1 If I load the edd module (BIOS Enhanced Disk Drive calls determine boot disk) the edd module tells me (if the disk is empty): 255 heads and 63 sektors/track after creating partitions with parted the edd module tells me 78 heads and 60 sektors/track.... The effect is not if I create the partitions with fdsik....
greetings mario Am Freitag, den 29.09.2006, 14:56 +0200 schrieb Mario Gzuk: > Hi, > we have the following problem: > parted say that the disk (see below) has BIOS cylinder,head,sector > geometry: 9729,255,63. > But it writes other informations into the first sector of the fat > partition... > In sektor 1 of the fat32 partition the 2 bytes with offset 26 should > show the number of heads for interupt 0x13. And IMHO that should be the > same as parted gets from the BIOS.... Or am i wrong? But at these 2 > bytes there is a value of "78" instead of "255". And also the 2 bytes > with offset 24 (which should contain the sectors per track for interupt > 0x13) shows 60 instead of 63. > These all leads to the result of a "ntldr not found" problem..... > > Maybe you can help me out of this ???? > > Here follows the system informations, if you need more let me know. > > _____________SYSTEM INFORMATIONS_______________________________________ > > here is the output from "parted /dev/dsk print unit s print unit chs > print" > > #parted start > Disk /dev/sda: 80.0GB > Sector size (logical/physical): 512B/512B > Partition Table: msdos > > Number Start End Size Type File system Flags > 1 0.51kB 4000MB 4000MB primary fat32 boot, lba > > > Disk /dev/sda: 156301487s > Sector size (logical/physical): 512B/512B > Partition Table: msdos > > Number Start End Size Type File system Flags > 1 1s 7812500s 7812500s primary fat32 boot, lba > > > Disk /dev/sda: 9729,80,62 > Sector size (logical/physical): 512B/512B > BIOS cylinder,head,sector geometry: 9729,255,63. Each cylinder is > 8225kB. > Partition Table: msdos > > Number Start End Type File system Flags > 1 0,0,1 486,77,59 primary fat32 boot, lba > ### parted end > > > Here are some additional informations about the system > > > ###dmesg start > BIOS-e820: 000000001ffd0000 - 0000000020000000 (ACPI NVS) > BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) > BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) > BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved) > 0MB HIGHMEM available. > 511MB LOWMEM available. > On node 0 totalpages: 131008 > DMA zone: 4096 pages, LIFO batch:0 > Normal zone: 126912 pages, LIFO batch:31 > DMI 2.3 present. > ACPI: RSDP (v000 ACPIAM ) @ > 0x000f9ed0 > ACPI: RSDT (v001 A M I OEMRSDT 0x02000616 MSFT 0x00000097) @ > 0x1ffc0000 > ACPI: FADT (v002 A M I OEMFACP 0x02000616 MSFT 0x00000097) @ > 0x1ffc0200 > ACPI: MADT (v001 A M I OEMAPIC 0x02000616 MSFT 0x00000097) @ > 0x1ffc0390 > ACPI: OEMB (v001 A M I OEMBIOS 0x02000616 MSFT 0x00000097) @ > 0x1ffd0040 > ACPI: DSDT (v001 A0128 A0128003 0x00000003 INTL 0x02002026) @ > 0x00000000 > ACPI: PM-Timer IO Port: 0x4008 > Allocating PCI resources starting at 30000000 (gap: > 20000000:dec00000) > Built 1 zonelists > Enabling fast FPU save and restore... done. > Enabling unmasked SIMD FPU exception support... done. > Initializing CPU#0 > PID hash table entries: 2048 (order: 11, 8192 bytes) > Detected 1808.896 MHz processor. > Using pmtmr for high-res timesource > Console: colour VGA+ 80x25 > Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) > Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) > Memory: 491936k/524032k available (3565k kernel code, 31592k > reserved, 1735k data, 324k init, 0k highmem) > Checking if this processor honours the WP bit even in supervisor > mode... Ok. > Calibrating delay using timer specific routine.. 3620.14 > BogoMIPS (lpj=1810070) > Security Framework v1.0.0 initialized > Capability LSM initialized > Mount-cache hash table entries: 512 > CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 > 00000000 00000001 00000000 00000001 > CPU: After vendor identify, caps: 078bfbff e3d3fbff 00000000 > 00000000 00000001 00000000 00000001 > CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 > bytes/line) > CPU: L2 Cache: 256K (64 bytes/line) > CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 > 00000001 00000000 00000001 > Intel machine check architecture supported. > Intel machine check reporting enabled on CPU#0. > CPU: AMD Sempron(tm) Processor 3100+ stepping 02 > Checking 'hlt' instruction... OK. > SMP alternatives: switching to UP code > Freeing SMP alternatives: 0k freed > ACPI: setting ELCR to 0200 (from 0e88) > checking if image is initramfs... it is > Freeing initrd memory: 20974k freed > NET: Registered protocol family 16 > ACPI: bus type pci registered > PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2 > Setting up standard PCI resources > ACPI: Subsystem revision 20060127 > ACPI: Interpreter enabled > ACPI: Using PIC for interrupt routing > ACPI: PCI Root Bridge [PCI0] (0000:00) > PCI: Probing PCI hardware (bus 00) > Boot video device is 0000:01:00.0 > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] > ACPI: Power Resource [ISAV] (on) > ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 11 12 14 15) > *0, disabled. > ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11 12 14 15) > *0, disabled. > ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 *11 12 14 15) > ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 11 12 14 15) > *0, disabled. > ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 *11 12 14 15) > ACPI: PCI Interrupt Link [LUS0] (IRQs *3 4 5 7 9 10 11 12 14 15) > ACPI: PCI Interrupt Link [LUS1] (IRQs 3 4 5 7 *9 10 11 12 14 15) > ACPI: PCI Interrupt Link [LUS2] (IRQs 3 4 5 7 9 *10 11 12 14 15) > ACPI: PCI Interrupt Link [LKLN] (IRQs 3 4 5 7 9 10 11 12 14 15) > *0, disabled. > ACPI: PCI Interrupt Link [LAUI] (IRQs 3 4 5 *7 9 10 11 12 14 15) > ACPI: PCI Interrupt Link [LKMO] (IRQs 3 4 5 7 9 10 11 12 14 15) > *0, disabled. > ACPI: PCI Interrupt Link [LKSM] (IRQs 3 4 5 7 9 10 11 12 14 15) > *0, disabled. > ACPI: PCI Interrupt Link [LTID] (IRQs 10) *0 > ACPI: PCI Interrupt Link [LTIE] (IRQs 10) *0, disabled. > ACPI: PCI Interrupt Link [LATA] (IRQs 3 4 6 7 10 11 12 *14 15) > Linux Plug and Play Support v0.97 (c) Adam Belay > pnp: PnP ACPI init > pnp: PnP ACPI: found 15 devices > SCSI subsystem initialized > usbcore: registered new driver usbfs > usbcore: registered new driver hub > PCI: Using ACPI for IRQ routing > PCI: If a device doesn't work, try "pci=routeirq". If it helps, > post a report > pnp: 00:0b: ioport range 0x480-0x487 has been reserved > pnp: 00:0b: ioport range 0xd00-0xd07 has been reserved > PCI: Bridge: 0000:00:0b.0 > IO window: disabled. > MEM window: fd900000-fe9fffff > PREFETCH window: e9800000-ed7fffff > PCI: Bridge: 0000:00:0e.0 > IO window: c000-cfff > MEM window: fea00000-feafffff > PREFETCH window: disabled. > PCI: Setting latency timer of device 0000:00:0e.0 to 64 > NET: Registered protocol family 2 > IP route cache hash table entries: 4096 (order: 2, 16384 bytes) > TCP established hash table entries: 16384 (order: 4, 65536 > bytes) > TCP bind hash table entries: 8192 (order: 3, 32768 bytes) > TCP: Hash tables configured (established 16384 bind 8192) > TCP reno registered > apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) > Total HugeTLB memory allocated, 0 > NTFS driver 2.1.27 [Flags: R/O]. > Initializing Cryptographic API > io scheduler noop registered > io scheduler anticipatory registered > io scheduler deadline registered > io scheduler cfq registered (default) > Real Time Clock Driver v1.12ac > Linux agpgart interface v0.101 (c) Dave Jones > agpgart: Detected AGP bridge 0 > agpgart: Setting up Nforce3 AGP. > agpgart: AGP aperture is 128M @ 0xf0000000 > ACPI: Power Button (FF) [PWRF] > ACPI: Power Button (CM) [PWRB] > ibm_acpi: ec object not found > Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing > disabled > serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > 00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 > irq 1,12 > serio: i8042 AUX port at 0x60,0x64 irq 12 > serio: i8042 KBD port at 0x60,0x64 irq 1 > mice: PS/2 mouse device common for all mice > input: PC Speaker as /class/input/input0 > input: AT Translated Set 2 keyboard as /class/input/input1 > input: ImExPS/2 Generic Explorer Mouse as /class/input/input2 > Floppy drive(s): fd0 is 1.44M > FDC 0 is a post-1991 82077 > RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 > blocksize > loop: loaded (max 8 devices) > nbd: registered device at major 43 > Intel(R) PRO/1000 Network Driver - version 7.0.33-k2 > Copyright (c) 1999-2005 Intel Corporation. > Intel(R) PRO/10GbE Network Driver - version 1.0.100-k2 > Copyright (c) 1999-2005 Intel Corporation. > dgrs: SW=$Id: dgrs.c,v 1.13 2000/06/06 04:07:00 rick Exp $ > FW=Build 550 11/16/96 03:45:15 > FW Version=$Version$ > pcnet32.c:v1.32 18.Mar.2006 [EMAIL PROTECTED] > e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI > e100: Copyright(c) 1999-2005 Intel Corporation > ThunderLAN driver v1.15 > TLAN: 0 devices installed, PCI: 0 EISA: 0 > ns83820.c: National Semiconductor DP83820 10/100/1000 driver. > forcedeth.c: Reverse Engineered nForce ethernet driver. Version > 0.54. > tun: Universal TUN/TAP device driver, 1.6 > tun: (C) 1999-2004 Max Krasnyansky <[EMAIL PROTECTED]> > ipw2100: Intel(R) PRO/Wireless 2100 Network Driver, git-1.2.2 > ipw2100: Copyright(c) 2003-2006 Intel Corporation > ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, > git-1.1.1 > ipw2200: Copyright(c) 2003-2006 Intel Corporation > STRIP: Version 1.3A-STUART.CHESHIRE (unlimited channels) > orinoco 0.15rc3 (David Gibson <[EMAIL PROTECTED]>, > Pavel Roskin <[EMAIL PROTECTED]>, et al) > orinoco_cs 0.15rc3 (David Gibson <[EMAIL PROTECTED]>, > Pavel Roskin <[EMAIL PROTECTED]>, et al) > orinoco_plx 0.15rc3 (Pavel Roskin <[EMAIL PROTECTED]>, David Gibson > <[EMAIL PROTECTED]>, Daniel Barlow <[EMAIL PROTECTED]>) > orinoco_pci 0.15rc3 (Pavel Roskin <[EMAIL PROTECTED]>, David Gibson > <[EMAIL PROTECTED]> & Jean Tourrilhes > <[EMAIL PROTECTED]>) > orinoco_tmd 0.15rc3 (Joerg Dorchain <[EMAIL PROTECTED]>) > orinoco_nortel 0.15rc3 (Tobias Hoffmann & Christoph Jungegger > <[EMAIL PROTECTED]>) > spectrum_cs 0.15rc3 (Pavel Roskin <[EMAIL PROTECTED]>, David Gibson > <[EMAIL PROTECTED]>, et al) > airo(): Probing for PCI adapters > airo(): Finished probing for PCI adapters > Loaded prism54 driver, version 1.2 > hostap_cs: 0.4.4-kernel (Jouni Malinen <[EMAIL PROTECTED]>) > hostap_plx: 0.4.4-kernel (Jouni Malinen <[EMAIL PROTECTED]>) > hostap_pci: 0.4.4-kernel (Jouni Malinen <[EMAIL PROTECTED]>) > dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17) > winbond-840.c:v1.01-d (2.4 port) Nov-17-2001 Donald Becker > <[EMAIL PROTECTED]> > http://www.scyld.com/network/drivers.html > Linux Tulip driver version 1.1.13 (May 11, 2002) > ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11 > PCI: setting IRQ 11 as level-triggered > ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNKC] -> GSI 11 > (level, low) -> IRQ 11 > tulip0: EEPROM default media type Autosense. > tulip0: Index #0 - Media MII (#11) described by a 21142 MII PHY > (3) block. > tulip0: MII transceiver #17 config 1000 status 782d advertising > 01e1. > eth0: Digital DS21143 Tulip rev 65 at 0001cc00, > 00:00:CB:53:4C:5C, IRQ 11. > uli526x: ULi M5261/M5263 net driver, version 0.9.3 (2005-7-29) > libata version 1.20 loaded. > ieee1394: Initialized config rom entry `ip1394' > ieee1394: raw1394: /dev/raw1394 device initialized > usbmon: debugfs is not available > usbcore: registered new driver libusual > usbcore: registered new driver usbhid > drivers/usb/input/hid-core.c: v2.6:USB HID core driver > usbcore: registered new driver usblcd > usbcore: registered new driver usbled > TCP bic registered > NET: Registered protocol family 1 > NET: Registered protocol family 10 > IPv6 over IPv4 tunneling driver > NET: Registered protocol family 17 > ieee80211: 802.11 data/management/control stack, git-1.1.7 > ieee80211: Copyright (C) 2004-2005 Intel Corporation > <[EMAIL PROTECTED]> > ieee80211_crypt: registered algorithm 'NULL' > ieee80211_crypt: registered algorithm 'WEP' > ieee80211_crypt: registered algorithm 'CCMP' > ieee80211_crypt: registered algorithm 'TKIP' > Using IPI Shortcut mode > ACPI wakeup devices: > PS2K PS2M UAR1 USB0 MAC USB1 USB2 P0P1 > ACPI: (supports S0 S1 S3 S4 S5) > drivers/rtc/hctosys.c: unable to open rtc device (rtc0) > Freeing unused kernel memory: 324k freed > 3ware 9000 Storage Controller device driver for Linux > v2.26.02.007. > 3ware Storage Controller device driver for Linux v1.26.02.001. > Loading Adaptec I2O RAID: Version 2.4 Build 5go > Detecting Adaptec I2O RAID controllers... > scsi: <fdomain> Detection failed (no card) > GDT-HA: Storage RAID Controller Driver. Version: 3.04 > GDT-HA: Found 0 PCI Storage RAID Controllers > Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 > ide: Assuming 33MHz system bus speed for PIO modes; override > with idebus=xx > ipr: IBM Power RAID SCSI Device Driver version: 2.1.3 (March 29, > 2006) > iscsi: registered transport (tcp) > nsp32: loading... > sata_nv 0000:00:0a.0: version 0.8 > ACPI: PCI Interrupt Link [LTID] BIOS reported IRQ 0, using IRQ > 10 > ACPI: PCI Interrupt Link [LTID] enabled at IRQ 10 > PCI: setting IRQ 10 as level-triggered > ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LTID] -> GSI 10 > (level, low) -> IRQ 10 > PCI: Setting latency timer of device 0000:00:0a.0 to 64 > ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xD000 irq 10 > ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xD008 irq 10 > ata1: SATA link up 1.5 Gbps (SStatus 113) > ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 > 87:4023 88:407f > ata1: dev 0 ATA-7, max UDMA/133, 156301488 sectors: LBA48 > nv_sata: Primary device added > nv_sata: Primary device removed > nv_sata: Secondary device removed > ata1: dev 0 configured for UDMA/133 > scsi0 : sata_nv > ata2: SATA link down (SStatus 0) > scsi1 : sata_nv > Vendor: ATA Model: ST3808110AS Rev: 3.AA > Type: Direct-Access ANSI SCSI revision: > 05 > SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) > sda: Write Protect is off > sda: Mode Sense: 00 3a 00 00 > SCSI device sda: drive cache: write back > SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) > sda: Write Protect is off > sda: Mode Sense: 00 3a 00 00 > SCSI device sda: drive cache: write back > sda: sda1 > sd 0:0:0:0: Attached scsi disk sda > sd 0:0:0:0: Attached scsi generic sg0 type 0 > Adaptec aacraid driver (1.1-5[2409]-mh1) > Emulex LightPulse Fibre Channel SCSI driver 8.1.6 > Copyright(c) 2004-2006 Emulex. All rights reserved. > megaraid cmm: 2.20.2.6 (Release Date: Mon Mar 7 00:01:03 EST > 2005) > megaraid: 2.20.4.8 (Release Date: Mon Apr 11 12:27:22 EST 2006) > megasas: 00.00.02.04 Fri Feb 03 14:31:44 PST 2006 > nsp_cs: loading... > QLogic Fibre Channel HBA Driver > Probing IDE interface ide0... > hda: TOSHIBA DVD-ROM SD-M1912, ATAPI CD/DVD-ROM drive > Probing IDE interface ide1... > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > ide-scsi is deprecated for cd burning! Use ide-cd and give > dev=/dev/hdX as device > scsi2 : SCSI host adapter emulation for IDE ATAPI devices > Vendor: TOSHIBA Model: DVD-ROM SD-M1912 Rev: TM01 > Type: CD-ROM ANSI SCSI revision: > 00 > sr0: scsi-1 drive > Uniform CD-ROM driver Revision: 3.20 > sr 2:0:0:0: Attached scsi CD-ROM sr0 > sr 2:0:0:0: Attached scsi generic sg1 type 5 > NFORCE3-250: IDE controller at PCI slot 0000:00:08.0 > NFORCE3-250: chipset revision 162 > NFORCE3-250: not 100% native mode: will probe irqs later > NFORCE3-250: 0000:00:08.0 (rev a2) UDMA133 controller > NFORCE3-250: port 0x01f0 already claimed by ide0 > ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, > hdd:pio > Probing IDE interface ide1... > ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 10 > ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [LUS2] -> GSI 10 > (level, low) -> IRQ 10 > PCI: Setting latency timer of device 0000:00:02.2 to 64 > ehci_hcd 0000:00:02.2: EHCI Host Controller > ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus > number 1 > ehci_hcd 0000:00:02.2: debug port 1 > PCI: cache line size of 64 is not supported by device > 0000:00:02.2 > ehci_hcd 0000:00:02.2: irq 10, io mem 0xfebffc00 > ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec > 2004 > usb usb1: configuration #1 chosen from 1 choice > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 8 ports detected > ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) > Driver (PCI) > ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 3 > PCI: setting IRQ 3 as level-triggered > ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 3 > (level, low) -> IRQ 3 > PCI: Setting latency timer of device 0000:00:02.0 to 64 > ohci_hcd 0000:00:02.0: OHCI Host Controller > ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus > number 2 > ohci_hcd 0000:00:02.0: irq 3, io mem 0xfebfd000 > usb usb2: configuration #1 chosen from 1 choice > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 4 ports detected > ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 9 > PCI: setting IRQ 9 as level-triggered > ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS1] -> GSI 9 > (level, low) -> IRQ 9 > PCI: Setting latency timer of device 0000:00:02.1 to 64 > ohci_hcd 0000:00:02.1: OHCI Host Controller > ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus > number 3 > ohci_hcd 0000:00:02.1: irq 9, io mem 0xfebfe000 > usb usb3: configuration #1 chosen from 1 choice > hub 3-0:1.0: USB hub found > hub 3-0:1.0: 4 ports detected > USB Universal Host Controller Interface driver v3.0 > BIOS EDD facility v0.16 2004-Jun-25, 1 devices found > eth0: Setting full-duplex based on MII#17 link partner > capability of 45e1. > eth0: no IPv6 routers present > ###dmesg end > > > ###lspci start > 00:00.0 0600: 10de:00e1 (rev a1) > 00:01.0 0601: 10de:00e0 (rev a2) > 00:01.1 0c05: 10de:00e4 (rev a1) > 00:02.0 0c03: 10de:00e7 (rev a1) > 00:02.1 0c03: 10de:00e7 (rev a1) > 00:02.2 0c03: 10de:00e8 (rev a2) > 00:06.0 0401: 10de:00ea (rev a1) > 00:08.0 0101: 10de:00e5 (rev a2) > 00:0a.0 0101: 10de:00e3 (rev a2) > 00:0b.0 0604: 10de:00e2 (rev a2) > 00:0e.0 0604: 10de:00ed (rev a2) > 00:18.0 0600: 1022:1100 > 00:18.1 0600: 1022:1101 > 00:18.2 0600: 1022:1102 > 00:18.3 0600: 1022:1103 > 01:00.0 0300: 102b:0525 (rev 85) > 02:08.0 0200: 1011:0019 (rev 41) > > 00:00.0 Host bridge: nVidia Corporation nForce3 250Gb Host > Bridge (rev a1) > Subsystem: ASUSTeK Computer Inc. Unknown device 813f > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR+ FastB2B- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > Region 0: Memory at f0000000 (32-bit, prefetchable) > [size=128M] > Capabilities: [44] HyperTransport: Slave or Primary > Interface > Command: BaseUnitID=0 UnitCnt=14 MastHost- > DefDir- DUL- > Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ > EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- > Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit > DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- > Link Control 1: CFlE- CST- CFE- <LkFail+ Init- > EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- > Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit > DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn- > Revision ID: 1.03 > Link Frequency 0: 800MHz > Link Error 0: <Prot- <Ovfl- <EOC- CTLTm- > Link Frequency Capability 0: 200MHz+ 300MHz+ > 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- > Vend- > Feature Capability: IsocFC+ LDTSTOP+ CRCTM- > ECTLT- 64bA- UIDRD- > Link Frequency 1: 200MHz > Link Error 1: <Prot- <Ovfl- <EOC- CTLTm- > Link Frequency Capability 1: 200MHz- 300MHz- > 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- > Vend- > Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- > RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- > SERRNFE- > Prefetchable memory behind bridge Upper: 00-00 > Bus Number: 00 > Capabilities: [c0] AGP version 2.0 > Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- > GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4 > Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- > 64bit- FW- Rate=x1 > > 00:01.0 ISA bridge: nVidia Corporation nForce3 250Gb LPC Bridge > (rev a2) > Subsystem: ASUSTeK Computer Inc. Unknown device 813f > Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- > VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 > > 00:01.1 SMBus: nVidia Corporation nForce 250Gb PCI System > Management (rev a1) > Subsystem: ASUSTeK Computer Inc. Unknown device 813f > Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > Interrupt: pin A routed to IRQ 0 > Region 0: I/O ports at 5080 [size=32] > Region 4: I/O ports at 5000 [size=64] > Region 5: I/O ports at 5040 [size=64] > Capabilities: [44] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 00:02.0 USB Controller: nVidia Corporation CK8S USB Controller > (rev a1) (prog-if 10 [OHCI]) > Subsystem: ASUSTeK Computer Inc. Unknown device 813f > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 (750ns min, 250ns max) > Interrupt: pin A routed to IRQ 3 > Region 0: Memory at febfd000 (32-bit, non-prefetchable) > [size=4K] > Capabilities: [44] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA > PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 00:02.1 USB Controller: nVidia Corporation CK8S USB Controller > (rev a1) (prog-if 10 [OHCI]) > Subsystem: ASUSTeK Computer Inc. Unknown device 813f > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 (750ns min, 250ns max) > Interrupt: pin B routed to IRQ 9 > Region 0: Memory at febfe000 (32-bit, non-prefetchable) > [size=4K] > Capabilities: [44] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA > PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 00:02.2 USB Controller: nVidia Corporation nForce3 EHCI USB 2.0 > Controller (rev a2) (prog-if 20 [EHCI]) > Subsystem: ASUSTeK Computer Inc. Unknown device 813f > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 (750ns min, 250ns max) > Interrupt: pin C routed to IRQ 10 > Region 0: Memory at febffc00 (32-bit, non-prefetchable) > [size=256] > Capabilities: [44] Debug port > Capabilities: [80] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA > PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 00:06.0 Multimedia audio controller: nVidia Corporation nForce3 > 250Gb AC'97 Audio Controller (rev a1) > Subsystem: ASUSTeK Computer Inc. Unknown device 812a > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 (500ns min, 1250ns max) > Interrupt: pin A routed to IRQ 7 > Region 0: I/O ports at e800 [size=256] > Region 1: I/O ports at ec00 [size=128] > Region 2: Memory at febfb000 (32-bit, non-prefetchable) > [size=4K] > Capabilities: [44] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 00:08.0 IDE interface: nVidia Corporation CK8S Parallel ATA > Controller (v2.5) (rev a2) (prog-if 8a [Master SecP PriP]) > Subsystem: ASUSTeK Computer Inc. Unknown device 813f > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 (750ns min, 250ns max) > Region 4: I/O ports at ffa0 [size=16] > Capabilities: [44] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 00:0a.0 IDE interface: nVidia Corporation CK8S Serial ATA > Controller (v2.5) (rev a2) (prog-if 85 [Master SecO PriO]) > Subsystem: ASUSTeK Computer Inc. Unknown device 813f > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > Latency: 0 (750ns min, 250ns max) > Interrupt: pin A routed to IRQ 10 > Region 0: I/O ports at 09f0 [size=8] > Region 1: I/O ports at 0bf0 [size=4] > Region 2: I/O ports at 0970 [size=8] > Region 3: I/O ports at 0b70 [size=4] > Region 4: I/O ports at d000 [size=16] > Region 5: I/O ports at dc00 [size=128] > Capabilities: [44] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 00:0b.0 PCI bridge: nVidia Corporation nForce3 250Gb AGP Host to > PCI Bridge (rev a2) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR+ FastB2B- > Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > Latency: 16 > Bus: primary=00, secondary=01, subordinate=01, > sec-latency=10 > I/O behind bridge: 0000f000-00000fff > Memory behind bridge: fd900000-fe9fffff > Prefetchable memory behind bridge: e9800000-ed7fffff > Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium > >TAbort- <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- > FastB2B- > > 00:0e.0 PCI bridge: nVidia Corporation nForce3 250Gb PCI-to-PCI > Bridge (rev a2) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR+ FastB2B- > Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast > >TAbort- <TAbort- <MAbort- >SERR+ <PERR- > Latency: 0 > Bus: primary=00, secondary=02, subordinate=02, > sec-latency=128 > I/O behind bridge: 0000c000-0000cfff > Memory behind bridge: fea00000-feafffff > Prefetchable memory behind bridge: fff00000-000fffff > Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium > >TAbort- <TAbort- <MAbort+ <SERR- <PERR+ > BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- > FastB2B- > > 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 > [Athlon64/Opteron] HyperTransport Technology Configuration > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > Capabilities: [80] HyperTransport: Host or Secondary > Interface > !!! Possibly incomplete decoding > Command: WarmRst+ DblEnd- > Link Control: CFlE- CST- CFE- <LkFail- Init+ > EOC- TXO- <CRCErr=0 > Link Config: MLWI=16bit MLWO=16bit LWI=16bit > LWO=16bit > Revision ID: 1.02 > > 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 > [Athlon64/Opteron] Address Map > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 > [Athlon64/Opteron] DRAM Controller > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 > [Athlon64/Opteron] Miscellaneous Control > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > > 01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA > G400/G450 (rev 85) (prog-if 00 [VGA]) > Subsystem: Matrox Graphics, Inc. Millennium G450 32Mb > SDRAM Dual Head > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- > VGASnoop- ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > Latency: 64 (4000ns min, 8000ns max), Cache Line Size 08 > Interrupt: pin A routed to IRQ 11 > Region 0: Memory at ea000000 (32-bit, prefetchable) > [size=32M] > Region 1: Memory at fe9fc000 (32-bit, non-prefetchable) > [size=16K] > Region 2: Memory at fe000000 (32-bit, non-prefetchable) > [size=8M] > Expansion ROM at fe9c0000 [disabled] [size=128K] > Capabilities: [dc] Power Management version 2 > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [f0] AGP version 2.0 > Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- > GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4 > Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- > 64bit- FW- Rate=x1 > > 02:08.0 Ethernet controller: Digital Equipment Corporation > DECchip 21142/43 (rev 41) > Subsystem: Compu-Shack Unknown device 4235 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ > VGASnoop- ParErr- Stepping- SERR+ FastB2B- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium > >TAbort- <TAbort- <MAbort- >SERR- <PERR- > Latency: 64 (5000ns min, 10000ns max), Cache Line Size > 08 > Interrupt: pin A routed to IRQ 11 > Region 0: I/O ports at cc00 [size=128] > Region 1: Memory at feaffc00 (32-bit, non-prefetchable) > [size=1K] > Expansion ROM at fea80000 [disabled] [size=256K] > > ###lspci end > > > ###fdisk start > > Disk /dev/sda: 80.0 GB, 80026361856 bytes > 255 heads, 63 sectors/track, 9729 cylinders > Units = cylinders of 16065 * 512 = 8225280 bytes > > ###fdsik end > > > > > ###memeinfo start > MemTotal: 513352 kB > MemFree: 434436 kB > Buffers: 0 kB > Cached: 64844 kB > SwapCached: 0 kB > Active: 18068 kB > Inactive: 49084 kB > HighTotal: 0 kB > HighFree: 0 kB > LowTotal: 513352 kB > LowFree: 434436 kB > SwapTotal: 0 kB > SwapFree: 0 kB > Dirty: 0 kB > Writeback: 0 kB > Mapped: 3988 kB > Slab: 8128 kB > CommitLimit: 256676 kB > Committed_AS: 4452 kB > PageTables: 120 kB > VmallocTotal: 507896 kB > VmallocUsed: 3068 kB > VmallocChunk: 504636 kB > HugePages_Total: 0 > HugePages_Free: 0 > HugePages_Rsvd: 0 > Hugepagesize: 4096 kB > ###meminfo end > > > ###cpuinfo start > processor : 0 > vendor_id : AuthenticAMD > cpu family : 15 > model : 44 > model name : AMD Sempron(tm) Processor 3100+ > stepping : 2 > cpu MHz : 1808.896 > cache size : 256 KB > fdiv_bug : no > hlt_bug : no > f00f_bug : no > coma_bug : no > fpu : yes > fpu_exception : yes > cpuid level : 1 > wp : yes > flags : fpu vme de pse tsc msr pae mce cx8 apic sep > mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 syscall nx > mmxext fxsr_opt lm 3dnowext 3dnow up pni lahf_lm ts fid vid ttp > tm stc > bogomips : 3620.14 > > ###cpuinfo end > > greetings mario gzuk > > > > _______________________________________________ > bug-parted mailing list > [email protected] > http://lists.gnu.org/mailman/listinfo/bug-parted _______________________________________________ bug-parted mailing list [email protected] http://lists.gnu.org/mailman/listinfo/bug-parted
