Hi,
I recently installed OpenBSD 4.7 amd64 onto a Pentium D desktop and ran
into an issue on the multi-processor kernel. If I type "boot bsd.sp" at
the boot> prompt to boot the single-processor kernel it works okay,
however. The error message when booting multi-processor is:
uvm_fault(0xffffffff80c9e980, 0x0, 0, 1) -> e
kernel: page fault trap, code=0
Stopped at azalia_set_command+0x25: move 0x68(%rdi),%rsi
ddb{0}>
The full message is at the end of the dmesg at the very bottom of this
email. I get this issue from simply booting up and it happens without me
typing any commands. When I type "show panic" it says "the kernel did
not panic". Also installing the i386 version did not solve the issue.
Other outputs are below.
Trace:
azalia_set_command() at azalia_set_command+0x25
azalia_comresp() at azalia_comresp+0x4d
azalia_unsol_event() at azalia_unsol_event+0x77
azalia_rirb_kick_unsol_events() at azalia_rirb_kick_unsol_events+0x74
softclock() at softclock+0x22c
softintr_dispatch() at softintr_dispatch+0x73
Xsoftclock() at Xsoftclock+0x2d
--- interrupt---
mpidle() at 0x8
end of kernel
end trace frame: 0x4, count: -8
PS:
PID PPID PGRP UID S FLAGS WAIT COMMAND
10993 1 1 0 3 0x2000080 nanosleep init
18 0 0 0 3 0x2100200 bored crypto
17 0 0 0 3 0x2100200 aiodoned aiodoned
16 0 0 0 3 0x2100200 syncer update
15 0 0 0 3 0x2100200 cleaner cleaner
14 0 0 0 3 0x100200 reaper reaper
13 0 0 0 3 0x2100200 pgdaemon pagedaemon
12 0 0 0 3 0x2100200 pftm pfpurge
11 0 0 0 3 0x2100200 usbevt usb4
10 0 0 0 3 0x2100200 usbevt usb3
9 0 0 0 3 0x2100200 usbevt usb2
8 0 0 0 3 0x2100200 usbevt usb1
7 0 0 0 3 0x2100200 usbtsk usbtask
6 0 0 0 3 0x2100200 usbevt usb0
5 0 0 0 3 0x2100200 acpi_idle acpi0
4 0 0 0 7 0x40100200 idle1
3 0 0 0 3 0x2100200 bored syswq
* 2 0 0 0 7 0x40100200 idle0
1 0 1 0 3 0x2004080 wait init
0 -1 0 0 3 0x2080200 scheduler swapper
Show Registers:
ds 0xeb00 acpi_pdirpa+0xa720
es 0x1f9e
fs 0x2540 mp_pdirpa+0xa720
gs 0xfcd8 acpi_pdirpa+0xb8f8
rdi 0
rsi 0x21
rbp 0xffff80001bc6fce0
rbx 0
rdx 0x4c
rcx 0xf0f
rax 0x4
r8 0
r9 0xa
r10 0
r11 0x246
r12 0x21
r13 0
r14 0xf0f
r15 0
rip 0xffffffff80449685 azalia_set_command+0x25
cs 0x8
rflags 0x10282 acpi_pdirpa+0xbea2
rsp 0xffff80001bc6fcb0
ss 0x10
azalia_set_command+0x25: movq 0x68(%rdi),%rsi
dmesg:
OpenBSD 4.7 (GENERIC.MP) #130: Wed Mar 17 20:48:50 MDT 2010
[email protected]:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 3209781248 (3061 MB)
avail mem = 3116867584 (2972 MB)
RTC BIOS diagnostic error 80<clock_battery>
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.3 @ 0xe53b0 (35 entries)
bios0: vendor Intel Corp. version "NT94510J.15A.0109.2006.0501.1628"
date 05/01/2006
bios0: Intel Corporation GT5012
acpi0 at bios0: rev 0
acpi0: tables DSDT FACP APIC WDDT MCFG ASF! HPET
acpi0: wakeup devices SLPB(S4) P32_(S4) UAR1(S4) PEX0(S4) PEX1(S4)
PEX2(S4) PEX3(S4 ) PEX4(S4) PEX5(S4) UHC1(S3) UHC2(S3) UHC3(S3) UHC4(S3)
EHCI(S3) AC9M(S4) AZAL (S4)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Pentium(R) D CPU 2.80 GHz, 2800.32 MHz
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,CNXT-ID,CX16,xTPR,NXE,LONG
cpu1: 1MB 64b/line 8-way L2 cache
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
ioapic0: misconfigured as apic 0, remapped to apid 2
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 3 (P32_)
acpiprt2 at acpi0: bus 1 (PEX0)
acpiprt3 at acpi0: bus -1 (PEX1)
acpiprt4 at acpi0: bus 2 (PEX2)
acpiprt5 at acpi0: bus -1 (PEX3)
acpiprt6 at acpi0: bus -1 (PEX4)
acpiprt7 at acpi0: bus -1 (PEX5)
acpicpu0 at acpi0
acpicpu1 at acpi0
acpibtn0 at acpi0: SLPB
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel 82945G Host" rev 0x02
vga1 at pci0 dev 2 function 0 "Intel 82945G Video" rev 0x02
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
intagp0 at vga1
agp0 at intagp0: aperture at 0xc0000000, size 0x10000000
inteldrm0 at vga1: apic 2 int 16 (irq 11)
drm0 at inteldrm0
azalia0 at pci0 dev 27 function 0 "Intel 82801GB HD Audio" rev 0x01:
apic 2 int 22 (irq 9)
azalia0: codecs: Sigmatel STAC9220/1
audio0 at azalia0
ppb0 at pci0 dev 28 function 0 "Intel 82801GB PCIE" rev 0x01: apic 2 int
17 (irq 255)
pci1 at ppb0 bus 1
ppb1 at pci0 dev 28 function 2 "Intel 82801GB PCIE" rev 0x01: apic 2 int
18 (irq 225)
pci2 at ppb1 bus 2
uhci0 at pci0 dev 29 function 0 "Intel 82801GB USB" rev 0x01: apic 2 int
23 (irq 10)
uhci1 at pci0 dev 29 function 1 "Intel 82801GB USB" rev 0x01: apic 2 int
19 (irq 11)
uhci2 at pci0 dev 29 function 2 "Intel 82801GB USB" rev 0x01: apic 2 int
18 (irq 9)
uhci3 at pci0 dev 29 function 3 "Intel 82801GB USB" rev 0x01: apic 2 int
16 (irq 11)
ehci0 at pci0 dev 29 function 7 "Intel 82801GB USB" rev 0x01: apic 2 int
23 (irq 10)
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb2 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0xe1
pci3 at ppb2 bus 3
"TI TSB43AB23 FireWire" rev 0x00 at pci3 dev 5 function 0 not configured
fxp0 at pci3 dev 8 function 0 "Intel 82801GB LAN" rev 0x01, i82562: apic
2 int 20 (irq 11), address 00:13:20:cf:fe:09
inphy0 at fxp0 phy 1: i82562ET 10/100 PHY, rev. 0
pcib0 at pci0 dev 31 function 0 "Intel 82801GB LPC" rev 0x01
pciide0 at pci0 dev 31 function 1 "Intel 82801GB IDE" rev 0x01: DMA,
channel 0 configured to compatibility, channel 1 configured to compatibility
atapiscsi0 at pciide0 channel 0 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TSSTcorp, CD/DVDW TS-H552B, GA04> ATAPI
5/cdrom removable
atapiscsi1 at pciide0 channel0 drive 1
scsibus1 at atapiscsi1: 2 targets
cd1 at scsibus1 targ 0 lun 0: <LITE-ON, CD-ROM LTN-4891S, NGS3> ATAPI
5/cdrom removable
cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
cd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 ignored (disabled)
pciide1 at pci0 dev 31 function 2 "Intel 82801GB SATA" rev 0x01: DMA,
channel 0 configured to native-PCI, channel 1 configured to native-PCI
pciide1: using apic 2 int 19 (irq 11) for native-PCI interrupt
wd0 at pciide1 channel 0 drive 1: <HDT722525DLA380>
wd0: 16-sector PIO, LBA48, 238475 MB, 488397168 sectors
wd0(pciide1:0:1): using PIO mode 4, Ultra-DMA mode 6
ichiic0 at pci0 dev 31 function 3 "Intel 82801GB SMBus" rev 0x01: apic 2
int 19 (irq 11)
iic0 at ichiic0
adt0 at iic0 addr 0x2e: emc6d100 rev 0x68
spdmem0 at iic0 add 0x50: 512MB DDR2 SDRAM non-parity PC2-4200CL5
spdmem1 at iic0 add 0x51: 1GB DDR2 SDRAM non-parity PC2-6400CL5
spdmem2 at iic0 add 0x52: 512MB DDR2 SDRAM non-parity PC2-4200CL5
spdmem3 at iic0 add 0x53: 1GB DDR2 SDRAM non-parity PC2-6400CL5
usb1 at uhci0: USB revision 1.0
uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb2 at uhci1: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci2: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci3: USB revision 1.0
uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at pcib0
isaadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4:ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
mtrr: Pentium Pro MTRR support
umass0 at uhub2 port 1 configuration 1 interface 0 "USB Reader" rev
1.10/1.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus2 at umass0: 2 targets, initiator 0
sd0 at scsibus2 targ 1 lun 0: <Generic, USB SD Reader, 1.00> SCSI0
0/direct removable
sd0: drive offline
sd1 at scsibus2 targ 1 lun 1: <Generic, USB SD Reader, 1.01> SCSI0
0/direct removable
sd1: drive offline
sd2 at scsibus2 targ 1 lun 2: <Generic, USB SD Reader, 1.02> SCSI0
0/direct removable
sd2: drive offline
sd3 at scsibus2 targ 1 lun 3: <Generic, USB SD Reader, 1.03> SCSI0
0/direct removable
sd3: drive offline
vscsi0 at root
scsibus3 at vscsi0: 256 targets
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
uvm_fault(0xffffffff80c9e980, 0x0, 0, 1) -> e
kernel: page fault trap, code=0
Stopped at azalia_set_command+0x25: movq 0x68(%rdi),%rsi
ddb{0}>
Thanks for your help. Let me know if you need anything else to diagnose
the issue.
Jack Enright
