I have a SunFire T2000 that I've chopped up into LDOMs. The primary domain and six of the LDOMs are running 6.1-STABLE just fine. I pulled down the May 22 snapshot, and it installs (with a strange error, see bottom of post), but the LDOM crashes upon boot. I just tried again with the May 24th snapshot, and I'm getting the same error. This seems to dump me into OpenBoot, not ddb. I can provide a shell on the primary domain, and serial console (over ssh) access to a developer if needed. I am not subscribed to bugs@, so please copy me off-list.
Sun Fire T200, No Keyboard Copyright 2010 Sun Microsystems, Inc. All rights reserved. OpenBoot 4.30.4.a, 3072 MB memory available, Serial #83548683. Ethernet address 0:14:4f:fa:da:b, Host ID: 84fada0b. Boot device: disk File and args: OpenBSD IEEE 1275 Bootblock 1.4 ..>> OpenBSD BOOT 1.9 Trying bsd... Booting /virtual-devices@100/channel-devices@200/disk@0:a/bsd 8381472@0x1000000+7136@0x17fe420+196864@0x1800000+3997440@0x1830100 symbols @ 0xfedcc3c0 155+553992+364844 start=0x1000000 [ using 919960 bytes of bsd ELF symbol table ] console is /virtual-devices@100/console@1 Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. Copyright (c) 1995-2017 OpenBSD. All rights reserved. https://www.OpenBSD.org OpenBSD 6.1-current (GENERIC.MP) #123: Tue May 23 21:16:40 MDT 2017 dera...@sparc64.openbsd.org:/usr/src/sys/arch/sparc64/compile/GENERIC.MP real mem = 3221225472 (3072MB) avail mem = 3145572352 (2999MB) mpath0 at root scsibus0 at mpath0: 256 targets mainbus0 at root: Sun Fire T200 cpu0 at mainbus0: SUNW,UltraSPARC-T1 (rev 0.0) @ 1200 MHz cpu1 at mainbus0: SUNW,UltraSPARC-T1 (rev 0.0) @ 1200 MHz cpu2 at mainbus0: SUNW,UltraSPARC-T1 (rev 0.0) @ 1200 MHz cpu3 at mainbus0: SUNW,UltraSPARC-T1 (rev 0.0) @ 1200 MHz vbus0 at mainbus0 "flashprom" at vbus0 not configured cbus0 at vbus0 vdsk0 at cbus0 chan 0x2: ivec 0x4, 0x5 scsibus1 at vdsk0: 2 targets sd0 at scsibus1 targ 0 lun 0: <SUN, Virtual Disk, 1.1> SCSI3 0/direct fixed sd0: 4000MB, 512 bytes/sector, 8192000 sectors vnet0 at cbus0 chan 0x3: ivec 0x6, 0x7, address 00:14:4f:f9:ce:e5 vcons0 at vbus0: ivec 0x111, console vrtc0 at vbus0 vscsi0 at root scsibus2 at vscsi0: 256 targets softraid0 at root scsibus3 at softraid0: 256 targets bootpath: /virtual-devices@100,0/channel-devices@200,0/disk@0,0 root on sd0a (65ce554ceba2f574.a) swap on sd0b dump on sd0b ERROR: Last Trap: Fast Data Access Protection {1} ok =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= * one odd thing happens during install: fatal in dhclient: yielding responsibility for vnet0 I worked around it by ^Z and manually running dhclient from the shell before foregrounding it. Full install log up to the error included below. OpenBSD 6.1-current (RAMDISK) #116: Mon May 22 13:59:22 MDT 2017 dera...@sparc64.openbsd.org:/usr/src/sys/arch/sparc64/compile/RAMDISK real mem = 3221225472 (3072MB) avail mem = 3150954496 (3004MB) mainbus0 at root: Sun Fire T200 cpu0 at mainbus0: SUNW,UltraSPARC-T1 (rev 0.0) @ 1200 MHz "SUNW,UltraSPARC-T1" at mainbus0 not configured "SUNW,UltraSPARC-T1" at mainbus0 not configured "SUNW,UltraSPARC-T1" at mainbus0 not configured vbus0 at mainbus0 "flashprom" at vbus0 not configured cbus0 at vbus0 vdsk0 at cbus0 chan 0x2: ivec 0x4, 0x5 scsibus0 at vdsk0: 2 targets sd0 at scsibus0 targ 0 lun 0: <SUN, Virtual Disk, 1.1> SCSI3 0/direct fixed sd0: 4000MB, 512 bytes/sector, 8192000 sectors vnet0 at cbus0 chan 0x3: ivec 0x6, 0x7, address 00:14:4f:f9:ce:e5 vcons0 at vbus0: ivec 0x111, console vrtc0 at vbus0 softraid0 at root scsibus1 at softraid0: 256 targets bootpath: /virtual-devices@100,0/channel-devices@200,0/disk@0,0 root on rd0a swap on rd0b dump on rd0b erase ^?, werase ^W, kill ^U, intr ^C, status ^T Welcome to the OpenBSD/sparc64 6.1 installation program. (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? i At any prompt except password prompts you can escape to a shell by typing '!'. Default answers are shown in []'s and are selected by pressing RETURN. You can exit this program at any time by pressing Control-C, but this can leave your system in an inconsistent state. System hostname? (short form, e.g. 'foo') puffyfivesnap Available network interfaces are: vnet0 vlan0. Which network interface do you wish to configure? (or 'done') [vnet0] IPv4 address for vnet0? (or 'dhcp' or 'none') [dhcp] DHCPDISCOVER on vnet0 - interval 1 fatal in dhclient: yielding responsibility for vnet0 IPv6 address for vnet0? (or 'autoconf' or 'none') [none] ^Z [1] + Suspended /install # dhclient vnet0 DHCPDISCOVER on vnet0 - interval 1 DHCPOFFER from 192.168.1.254 (f8:18:97:8f:a5:09) DHCPREQUEST on vnet0 to 255.255.255.255 DHCPACK from 192.168.1.254 (f8:18:97:8f:a5:09) bound to 192.168.1.70 -- renewal in 43200 seconds. # fg /install Available network interfaces are: vnet0 vlan0. Which network interface do you wish to configure? (or 'done') [done] Using DNS domainname attlocal.net Using DNS nameservers at 192.168.1.254 TIA --ax0n http://www.h-i-r.net/