Hi all, Seems to be some problem with newer versions. I am currently stuck on not getting a bootable machine. Attached boot log, the boot process just hangs at the last line.
Thanks, Aisha U-Boot SPL 2020.10 (Nov 13 2020 - 18:48:26 -0700) DRAM: 2048 MiB Trying to boot from MMC1 NOTICE: BL31: v2.3():2.3 NOTICE: BL31: Built : 18:10:52, Nov 13 2020 NOTICE: BL31: Detected Allwinner A64/H64/R18 SoC (1689) NOTICE: BL31: Found U-Boot DTB at 0x4093788, model: Pine64 LTS INFO: ARM GICv2 driver initialized INFO: Configuring SPC Controller INFO: PMIC: Probing AXP803 on RSB INFO: PMIC: dcdc1 voltage: 3.300V INFO: PMIC: dcdc5 voltage: 1.200V INFO: PMIC: dcdc6 voltage: 1.100V INFO: PMIC: dldo1 voltage: 3.300V INFO: PMIC: dldo2 voltage: 3.300V INFO: PMIC: dldo4 voltage: 3.300V INFO: PMIC: fldo1 voltage: 1.200V INFO: PMIC: Enabling DC SW INFO: BL31: Platform setup done INFO: BL31: Initializing runtime services INFO: BL31: cortex_a53: CPU workaround for 843419 was applied INFO: BL31: cortex_a53: CPU workaround for 855873 was applied NOTICE: PSCI: System suspend is unavailable INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x4a000000 INFO: SPSR = 0x3c9 alloc space exhausted U-Boot 2020.10 (Nov 13 2020 - 18:48:26 -0700) Allwinner Technology CPU: Allwinner A64 (SUN50I) Model: Pine64 LTS DRAM: 2 GiB MMC: mmc@1c0f000: 0, mmc@1c11000: 1 Loading Environment from FAT... Card did not respond to voltage select! In: serial Out: serial Err: serial Net: phy interface7 eth0: ethernet@1c30000 starting USB... Bus usb@1c1a000: USB EHCI 1.00 Bus usb@1c1a400: USB OHCI 1.0 Bus usb@1c1b000: USB EHCI 1.00 Bus usb@1c1b400: USB OHCI 1.0 scanning bus usb@1c1a000 for devices... 1 USB Device(s) found scanning bus usb@1c1a400 for devices... 1 USB Device(s) found scanning bus usb@1c1b000 for devices... 1 USB Device(s) found scanning bus usb@1c1b400 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... 27644 bytes read in 3 ms (8.8 MiB/s) Found EFI removable media binary efi/boot/bootaa64.efi Scanning disk m...@1c0f000.blk... ** Unrecognized filesystem type ** Card did not respond to voltage select! Scanning disk m...@1c11000.blk... Disk m...@1c11000.blk not ready Found 3 disks No EFI system partition BootOrder not defined EFI boot manager: Cannot load any image 168696 bytes read in 10 ms (16.1 MiB/s) Booting /efi\boot\bootaa64.efi disks: sd0* >> OpenBSD/arm64 BOOTAA64 1.2 boot> NOTE: random seed is being reused. booting sd0a:/bsd: 8651704+1774048+562840+825664 [625368+109+1058136+621036]=0xf85e28 EHCI failed to shut down host controller. type 0x2 pa 0x40000000 va 0x40000000 pages 0x4000 attr 0x8 type 0x7 pa 0x44000000 va 0x44000000 pages 0x3ef6 attr 0x8 type 0x9 pa 0x47ef6000 va 0x47ef6000 pages 0x14 attr 0x8 type 0x7 pa 0x47f0a000 va 0x47f0a000 pages 0x701f5 attr 0x8 type 0x2 pa 0xb80ff000 va 0xb80ff000 pages 0xcef attr 0x8 type 0x4 pa 0xb8dee000 va 0xb8dee000 pages 0x1 attr 0x8 type 0x2 pa 0xb8def000 va 0xb8def000 pages 0x3 attr 0x8 type 0x7 pa 0xb8df2000 va 0xb8df2000 pages 0x1 attr 0x8 type 0x2 pa 0xb8df3000 va 0xb8df3000 pages 0x100 attr 0x8 type 0x1 pa 0xb8ef3000 va 0xb8ef3000 pages 0x2a attr 0x8 type 0x0 pa 0xb8f1d000 va 0xb8f1d000 pages 0x5 attr 0x8 type 0x4 pa 0xb8f22000 va 0xb8f22000 pages 0x1 attr 0x8 type 0x6 pa 0xb8f23000 va 0x149d8e000 pages 0x1 attr 0x8000000000000008 type 0x4 pa 0xb8f24000 va 0xb8f24000 pages 0x2 attr 0x8 type 0x0 pa 0xb8f26000 va 0xb8f26000 pages 0x1 attr 0x8 type 0x6 pa 0xb8f27000 va 0x149d92000 pages 0x3 attr 0x8000000000000008 type 0x4 pa 0xb8f2a000 va 0xb8f2a000 pages 0x1 attr 0x8 type 0x6 pa 0xb8f2b000 va 0x149d96000 pages 0x4 attr 0x8000000000000008 type 0x0 pa 0xb8f2f000 va 0xb8f2f000 pages 0x1 attr 0x8 type 0x4 pa 0xb8f30000 va 0xb8f30000 pages 0x1 attr 0x8 type 0x0 pa 0xb8f31000 va 0xb8f31000 pages 0x1 attr 0x8 type 0x4 pa 0xb8f32000 va 0xb8f32000 pages 0x2 attr 0x8 type 0x0 pa 0xb8f34000 va 0xb8f34000 pages 0x1 attr 0x8 type 0x4 pa 0xb8f35000 va 0xb8f35000 pages 0x1 attr 0x8 type 0x0 pa 0xb8f36000 va 0xb8f36000 pages 0x2 attr 0x8 type 0x4 pa 0xb8f38000 va 0xb8f38000 pages 0x1 attr 0x8 type 0x0 pa 0xb8f39000 va 0xb8f39000 pages 0x1 attr 0x8 type 0x2 pa 0xb8f3a000 va 0xb8f3a000 pages 0x5026 attr 0x8 type 0x5 pa 0xbdf60000 va 0x14edcb000 pages 0x10 attr 0x8000000000000008 type 0x2 pa 0xbdf70000 va 0xbdf70000 pages 0x2090 attr 0x8 [ using 2305616 bytes of bsd ELF symbol table ] Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. Copyright (c) 1995-2020 OpenBSD. All rights reserved. https://www.OpenBSD.org OpenBSD 6.8-current (GENERIC.MP) #905: Thu Nov 19 22:40:17 MST 2020 dera...@arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/GENERIC.MP real mem = 2014228480 (1920MB) avail mem = 1919954944 (1831MB) random: boothowto does not indicate good seed mainbus0 at root: Pine64 LTS psci0 at mainbus0: PSCI 1.1, SMCCC 1.2 cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4 cpu0: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache cpu0: 512KB 64b/line 16-way L2 cache cpu0: CRC32,SHA2,SHA1,AES+PMULL cpu1 at mainbus0 mpidr 1: ARM Cortex-A53 r0p4 cpu1: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache cpu1: 512KB 64b/line 16-way L2 cache cpu1: CRC32,SHA2,SHA1,AES+PMULL cpu2 at mainbus0 mpidr 2: ARM Cortex-A53 r0p4 cpu2: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache cpu2: 512KB 64b/line 16-way L2 cache cpu2: CRC32,SHA2,SHA1,AES+PMULL cpu3 at mainbus0 mpidr 3: ARM Cortex-A53 r0p4 cpu3: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache cpu3: 512KB 64b/line 16-way L2 cache cpu3: CRC32,SHA2,SHA1,AES+PMULL efi0 at mainbus0: UEFI 2.8 efi0: Das U-Boot rev 0x20201000 apm0 at mainbus0 "display-engine" at mainbus0 not configured "osc24M_clk" at mainbus0 not configured "osc32k_clk" at mainbus0 not configured "pmu" at mainbus0 not configured simpleaudio0 at mainbus0 agtimer0 at mainbus0: tick rate 24000 KHz simplebus0 at mainbus0: "soc" sxisyscon0 at simplebus0 sxisid0 at simplebus0 sxiccmu0 at simplebus0 sxipio0 at simplebus0: 103 pins ampintc0 at simplebus0 nirq 224, ncpu 4 ipi: 0, 1: "interrupt-controller" sxirtc0 at simplebus0 sxiccmu1 at simplebus0 sxipio1 at simplebus0: 13 pins sxirsb0 at simplebus0 axppmic0 at sxirsb0 addr 0x3a3: AXP803 "bus" at simplebus0 not configured "dma-controller" at simplebus0 not configured "lcd-controller" at simplebus0 not configured "lcd-controller" at simplebus0 not configured "video-codec" at simplebus0 not configured sximmc0 at simplebus0 sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma sximmc1 at simplebus0 sdmmc1 at sximmc1: 8-bit, sd high-speed, mmc high-speed, dma "crypto" at simplebus0 not configured "usb" at simplebus0 not configured "phy" at simplebus0 not configured ehci0 at simplebus0 usb0 at ehci0: USB revision 2.0 uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00 addr 1 ohci0 at simplebus0: version 1.0 ehci1 at simplebus0 usb1 at ehci1: USB revision 2.0 uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00 addr 1 ohci1 at simplebus0: version 1.0 "dai" at simplebus0 not configured "codec" at simplebus0 not configured sxitemp0 at simplebus0 com0 at simplebus0: ns16550, no working fifo com0: console "spi" at simplebus0 not configured dwxe0 at simplebus0: address 02:ba:17:b1:0f:02 rgephy0 at dwxe0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5 "gpu" at simplebus0 not configured "dram-controller" at simplebus0 not configured "deinterlace" at simplebus0 not configured "hdmi" at simplebus0 not configured "hdmi-phy" at simplebus0 not configured "interrupt-controller" at simplebus0 not configured "codec-analog" at simplebus0 not configured sxidog0 at simplebus0 gpio0 at sxipio0: 32 pins gpio1 at sxipio0: 32 pins gpio2 at sxipio0: 32 pins gpio3 at sxipio0: 32 pins gpio4 at sxipio0: 32 pins gpio5 at sxipio0: 32 pins gpio6 at sxipio0: 32 pins gpio7 at sxipio0: 32 pins gpio8 at sxipio1: 32 pins usb2 at ohci0: USB revision 1.0 uhub2 at usb2 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00 addr 1 usb3 at ohci1: USB revision 1.0 uhub3 at usb3 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00 addr 1 "opp_table0" at mainbus0 not configured "hdmi-connector" at mainbus0 not configured "vcc1v8" at mainbus0 not configured sdmmc1: can't enable card scsibus0 at sdmmc0: 2 targets, initiator 0 sd0 at scsibus0 targ 1 lun 0: <SD/MMC, 00000, 0010> removable sd0: 14991MB, 512 bytes/sector, 30702592 sectors vscsi0 at root scsibus1 at vscsi0: 256 targets softraid0 at root scsibus2 at softraid0: 256 targets root on sd0a (4c56527a87ee78f4.a) swap on sd0b dump on sd0b
