kn@: I will take a look at my earlier bug report with the RISCV disk encryption bug in the installer.
Right now I have installed OpenBSD/riscv64 on my Mango Pi. Thank you very much OpenBSD! This is a great effort making this mango pi work! I found that I needed a new kernel to detect the sd/mmc tf cards. So I went about making a new ramdisk with /usr/src/distrib/riscv64/ramdisk/ I noticed that there is a problem with libstubs in this process from a "vanilla" riscv64 build box. It will error out. The work around is to go into /usr/src/distrib/special/libstubs and manually make it there, where it gets ranlib'ed. Then go back to the former path and continue making the ramdisk. Wanted to let you know this. Dmesg follows: OpenBSD 7.4-current (MANGOPI) #0: Fri Feb 16 16:32:50 CET 2024 p...@stern.delphinusdns.org:/sys/arch/riscv64/compile/MANGOPI real mem = 1073741824 (1024MB) avail mem = 1008390144 (961MB) SBI: OpenSBI v1.3, SBI Specification Version 1.0 random: good seed from bootblocks mainbus0 at root: MangoPi MQ Pro cpu0 at mainbus0: T-Head arch 0 imp 0 rv64imafdc intc0 at cpu0 cpu0: 32KB 64b/line 128-way L1 I-cache, 32KB 64b/line 256-way L1 D-cache "fit-images" at mainbus0 not configured "dcxo-clk" at mainbus0 not configured simplebus0 at mainbus0: "soc" sxipio0 at simplebus0: 88 pins sxiccmu0 at simplebus0 plic0 at simplebus0 sxitimer0 at simplebus0: 24000 kHz sxidog0 at simplebus0 com0 at simplebus0: dw16550 com0: console com1 at simplebus0: dw16550 "syscon" at simplebus0 not configured "dma-controller" at simplebus0 not configured "efuse" at simplebus0 not configured "crypto" at simplebus0 not configured "dram-controller" at simplebus0 not configured sximmc0 at simplebus0 sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma sximmc1 at simplebus0 sdmmc1 at sximmc1: 4-bit, sd high-speed, mmc high-speed, dma "usb" at simplebus0 not configured "phy" at simplebus0 not configured ehci0 at simplebus0 usb0 at ehci0: USB revision 2.0 uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00 addr 1 ohci0 at simplebus0: version 1.0 "clock-controller" at simplebus0 not configured "mixer" at simplebus0 not configured "mixer" at simplebus0 not configured "phy" at simplebus0 not configured "tcon-top" at simplebus0 not configured "lcd-controller" at simplebus0 not configured "lcd-controller" at simplebus0 not configured "power-controller" at simplebus0 not configured "clock-controller" at simplebus0 not configured sxirtc0 at simplebus0 sxidog1 at simplebus0 sxidog2 at simplebus0 gpio0 at sxipio0: 32 pins gpio1 at sxipio0: 32 pins gpio2 at sxipio0: 32 pins gpio3 at sxipio0: 32 pins gpio4 at sxipio0: 32 pins gpio5 at sxipio0: 32 pins gpio6 at sxipio0: 32 pins usb1 at ohci0: USB revision 1.0 uhub1 at usb1 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00 addr 1 "opp-table-cpu" at mainbus0 not configured "pmu" at mainbus0 not configured "vcc" at mainbus0 not configured "vcc-3v3" at mainbus0 not configured "leds" at mainbus0 not configured "avdd2v8" at mainbus0 not configured "dvdd" at mainbus0 not configured "vdd-cpu" at mainbus0 not configured "wifi-pwrseq" at mainbus0 not configured "binman" at mainbus0 not configured scsibus0 at sdmmc0: 2 targets, initiator 0 sd0 at scsibus0 targ 1 lun 0: <Sandisk, SD32G, 0085> removable sd0: 30436MB, 512 bytes/sector, 62333952 sectors manufacturer 0x024c, product 0xd723 at sdmmc1 function 1 not configured uhub2 at uhub0 port 1 configuration 1 interface 0 "vendor 0x1a40 USB 2.0 Hub" rev 2.00/1.11 addr 2 ure0 at uhub2 port 4 configuration 1 interface 0 "Realtek USB 10/100 LAN" rev 2.10/20.00 addr 3 ure0: RTL8152 (0x4c10), address 00:e0:4c:36:00:e9 rlphy0 at ure0 phy 0: RTL8201E 10/100 PHY, rev. 2 vscsi0 at root scsibus1 at vscsi0: 256 targets softraid0 at root scsibus2 at softraid0: 256 targets root on sd0a (ff09abc802626de6.a) swap on sd0b dump on sd0b sxiccmu_d1_set_frequency: 0x00000084 cpu0: clock not implemented Thanks and best regards! -pjp - Note: My signature has changed.