Thanks Jonathan,

The golden question, perhaps not easy to answer, is knowing the threshold of
operating environment for the power supplies and the chassis in current
form.

Many users, I suspect, may not be aware or have considered operating
environment or even cycle times.

If they are aware of approaching boundaries where additional steps maybe
prudent to ensure long term use of the equipment they can  be prepared to
adapt to the modifications you have suggested.

Still, doing mods one or few at a time, as opposed the large quantity
deployed, may have its own challenges.

Finally, many thanks for offering to share your pains.

Best regards,

Mo

Digicom

510-639-7003

  _____  

From: Jonathan Weintroub [mailto:[email protected]] 
Sent: Thursday, July 07, 2016 1:33 PM
To: casper
Cc: Mo Ohady; Alec Rust
Subject: Re: [casper] ROACH2 Power supply issue

 

An addendum to Alec's note on a power supply mounting idea: 

 

At SAO we adopted the FSP250-60FAG power supply for our latest build of
ROACH2s currently in process at Digicom. We also had trouble with the iStar
(sometimes labelled XEAL), and have had better experience with the FSP>

 

We came up with an installation scheme which suits us-though certainly won't
suit everyone.  It involves fairly substantial mechanical modifications to
the ROACH2 enclosure, and resulting machining expense.  I thought I would
share briefly what this looks like with pros and cons.  If CASPERites want
to use this scheme, we are as always happy to share drawings and
experiences.

 

The attached photos detail that we have machined out an aperture in the rear
panel of the ROACH2 behind the power supply location, removed the power
entry and EMI filter and line power pigtail, and moved the power supply back
flush with the rear panel.   Threaded holes in the power supply matched with
through holes in the rear panel are used to screw it in place.  We also
machine away part of the top flange to which the enclosure lid screws. 

 

Pros:

Eliminating the power entry and pigtail means fewer connections on the line
power path, it's just simpler overall.

The FSP mounts securely, the way it was intended to be used.

The power supply vents directly to the outside of the enclosure rather than
contributing heat to the inside.

 

Cons:

We are not as concerned as the enclosure designers (MeerKAT) with EMI
compatibility-the mechanical mods almost certainly make the enclosure less
RFI tight than it was spec'ed.

Removing the EMI filter doesn't help in this regard either.

Nor do the screw holes in the lid which no longer have mates in the flange.

The original design of the enclosure used the part of the rear panel which
we removed to mount up to 8 SMA RF connectors to bring analog signals into
the enclosure.  This modification is not compatible with this routing.

There is additional cost per unit in the mechanical mods, likely greater for
small production numbers.

 

Jonathan

 

 





On Jul 6, 2016, at 11:27 AM, Alec Rust <[email protected]> wrote:

Hi all, SKA-SA have suffered a number of ROACH2 power supply failures. After
investigation we determined that the power supplies (ISTAR TC-20FX2)
overheat and then fail. This is due to obstructed airflow and fan failure.
The front air intake of the ISTAR is almost completely blocked by the wire
loom, and the fan is of the sleeve bearing type. In all the failed power
supplies the fans had seized.

One workaround is to set the ROACH2 enclosure fans to maximum, this will
force some air through the power supply. Our failure rate dropped
significantly after setting the fans to maximum, but we still encountered
failures. This can be done by commenting out the following line in
/etc/tcpborphserver3.init:
#?job process r2fanctrl exec://r2fanctrl


We have identified another power supply by FSP (FSP250-60FAG). We have not
had any failures using this supply and more than 50 boards have been running
for 3 months. The supplies do not have the correct mounting holes, so
fitting them is an issue. We have used thin double sided tape, but this will
not be sufficient if the LRU is to be transported.

If you have any questions do not hesitate to contact me.

Regards
Alec Rust
SKA-SA

 

 

 






No virus found in this message.
Checked by AVG - www.avg.com
Version: 2016.0.7687 / Virus Database: 4613/12574 - Release Date: 07/07/16

Reply via email to