I neglected to copy the list with my response to Kaushal:

To use an external clock, you need to install jumper J4:
[image: Inline image 1]
Then you bring in the signal on J13 pins 36 & 38:
[image: Inline image 2]
The ICS8308 can accept a wide range of signal amplitude and common-mode
voltage:
[image: Inline image 3]
It has a 3.3v supply, so LVDS levels will work.  I've used it successfully
with LVDS from an FPGA.

On Fri, Jan 20, 2017 at 7:11 PM, Jack Hickish <[email protected]> wrote:

> Hi Kaushal,
>
> Matt Dexter got in touch about this, and points out that table 4D of
> https://www.idt.com/document/dst/ics8308i-datasheet shows the
> requirements of CLK, nCLK on the ADC64's U1 as operating at 3.3V = VDD =
> VDDO. Page 11 has very examples of CLK, nCLK source circuits.
>
> Looking at the biasing in the ADC schematics and comparing with the
> examples I think you need to apply an LVDS driver to pins 36/38 of J13.
> More importantly, Matt agreed that this is what he'd try first (though
> notes that other drivers should also work).
>
> Hope that helps,
>
> Jack
>
> On Wed, 18 Jan 2017 at 20:32 Kaushal Buch <[email protected]> wrote:
>
>> Hi Jack,
>>
>> Thanks for the reply.
>>
>> The design compiled for 260 MHz (adc0_clk) with yellow block set to 65
>> MHz.
>>
>> However, I am not yet clear about the external clock input requirements.
>>
>>
>>
>> Regards,
>>
>> Kaushal
>>
>> On 1/2/17, Jack Hickish <[email protected]> wrote:
>> > Hi Kaushal,
>> >
>> > On Mon, 2 Jan 2017 10:16 am Kaushal Buch, <[email protected]>
>> wrote:
>> >
>> >> Dear all,
>> >>
>> >> We have interfaced 64-channel ADC with ROACH-1 board and it is working
>> >> as expected using on-board clock (50MHz). There is provision to
>> >> provide an external clock to this board to operate ADC to get a
>> >> maximum data rate of 65 MSPS. However, we have a few queries and need
>> >> inputs on the following:
>> >>
>> >> 1. What should be the power level for the external clock ?
>> >>
>> >
>> > If I remember correctly, I believe it takes an LVPECL input.
>> >
>> >
>> >
>> >> 2. On the ROACH-1 side, we have x64-adc yellow block interface where
>> >> we can set the ADC clock rate. Should we enter 65MHz over there? Will
>> >> the default yellow block support this ?
>> >>
>> >
>> > Yes, set the yellow block to 65MHz. I doubt anyone has tried this, so
>> while
>> > it should work, maybe you'll encounter some timing problems.
>> >
>> >
>> >
>> >> 3. If x64_adc is operated at 65MHz clock, ROACH-1 has to be operated
>> >> at 4 times the ADC clock i.e. 260MHz. Should XSG_core_config settings,
>> >> 'arb_clk' be set to 260 MHz? As 'arb_clk' is derived from internal
>> >> clock using DCM, how is the stability of 'arb_clk' at 260MHz? Has
>> >> anyone used this ?
>> >>
>> >
>> > You want adc0_clk, set to 260MHz.
>> >
>> > Cheers,
>> >
>> > Jack
>> >
>> >
>> >>
>> >> Thanks & Regards,
>> >>
>> >> Kaushal
>> >>
>> >>
>> >
>>
>

Reply via email to