Hi Jonathan,

Here are the answers to 1 and 2 below:

1) Yes, there is a an external clock reference. There are three SMA
connectors on the SKARAB motherboard within the enclosure: AUX_CLK_IN,
AUX_SYNC_IN and AUX_SYNC_OUT. The current ADC Mezzanine Card makes use of
these interfaces. The current BSP package that we provide does not use
these interfaces, so in order to use them you would need to do some
firmware changes. You can see more about these interfaces by reading the
SKARAB Hardware Description Document, which is located in
https://github.com/ska-sa/skarab_docs (master branch). The SKARAB wiki is
officially up and running, so check out:
https://casper.berkeley.edu/wiki/SKARAB.
<https://casper.berkeley.edu/wiki/SKARAB> It contains all the relevant
links - apologies for the shameful advertising :). In order to use a
reference clock then you would need the Mezzanine 1 or 2 slot open, so that
you can feed a cable through to the SMA. Clifford, can probably confirm
this.

2) The SKARAB BSP package runs off the 156.25MHz clock and this is
currently not configurable via the toolflow. The SKARAB motherboard  has an
on-board 156.25MHz LVPECL oscillator, which it uses as the main clock
source.The SKARAB BSP does make provision for a user_clk, which is the
toolflow clock, but right now there is only one. It would be easy enough to
add another if required. You could just add another clock to the output of
the user_clk MMCM and feed it into the toolflow, but this would mean
firmware changes. In our case, the SKARAB is using a multi clock design, as
the BSP is running off the 156.25MHz and the DSP is running off the 230MHz
clock generated from the 156.25MHz clock, but I think you are referring to
working with two clocks within the DSP Simulink block.

Kind regards,

Adam



On Wed, Jul 26, 2017 at 10:19 PM, Jonathan Weintroub <
[email protected]> wrote:

> Hi CASPER, SKARAB, JASPER collaborators,
>
> As much prior traffic has documented we are bring up SKARABs at SAO, and
> working on a fast rate interpolator design.  After teething troubles with
> the SKARAB and JASPER Mark Peryer is now successfully building, loading and
> running codes on SKARAB. A few questions have come up as we dig deeper.
> The topics all come back to this one design, so I will bundle them into one
> email, and hope to catch some fish.
>
> 1.  The SKARAB is internally clocked, there appears to be no external
> clock reference in. Is it possible to lock the SKARAB processing to some
> external reference or clock?
>
> 2.  Does JASPER running on SKARAB support FPGA designs with multiple clock
> domains?
>
> 3.  Has anyone in the community produced  non-radix-2 demultiplexed
> CASPER, or, JASPER, FFT blocks?
>
> 4.  Has anyone done CASPER or JASPER work on rate interpolation
> (downsampling) with arbitrary, and unfriendly, factors?
>
> Thanks very much in advance for any contributions.
>
> Jonathan
>
>
>
> --
> You received this message because you are subscribed to the Google Groups "
> [email protected]" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to [email protected].
> To post to this group, send email to [email protected].
>



-- 
[image: SKA_banner]

Best Regards / Vriendelike Groete

*Adam Isaacson*
FPGA Engineer

[image: SKA_banner][image: SKA_banner]
[image: SKA_banner]   (+27) 82 563 9602 [image: SKA_banner]   3rd Floor,
The Park, Park Road,
[image: SKA_banner]   (+27) 21 506 7300     Pinelands
[image: SKA_banner]   (+27) 21 506 7375     7405
[image: SKA_banner]   www.ska.ac.za     South Africa

-- 
You received this message because you are subscribed to the Google Groups 
"[email protected]" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to [email protected].
To post to this group, send email to [email protected].

Reply via email to