Hi Jack,

Would that be akin to the calibration routine which was written for the
ADC5G? I will be at the workshop, and can definitely bring a test setup.

Thanks,
Sam

On Thu, Aug 3, 2017 at 2:08 PM, Jack Hickish <[email protected]> wrote:

> Hi Sam,
>
> I'm not familiar with the music board, but I wonder if it would benefit
> from tuning the clock vs data skew on the adc->fpga links to tune the data
> capture for reliability.
>
> Are you coming to the CASPER workshop? If so I suggest bringing a music
> board and maybe somebody can donate some time to investigate your problem.
>
> Cheers
> Jack
>
> On Thu, Aug 3, 2017, 10:57 PM Sam Gordon <[email protected]> wrote:
>
>> Hi all,
>>
>> I seek your insight into an issue which my collaborators and I have been
>> troubleshooting for some time. It has to do with a 1024 channel Roach2
>> spectrometer which uses the MUSIC DAC/ADC board. The Roach is clocked at
>> 256 MHz, which it derives from a 512 MHz input to the MUSIC board (taken
>> from one of the ADC channels). After making several duplicates of the
>> system (hardware, firmware and software), we noticed that a few of them
>> (something like one out of six) exhibit spurious voltage spikes in the ADC
>> time streams, which are visible via snap block readout. The effect of the
>> glitches is to increase the overall amplitude noise level at the channel
>> outputs, so we'd like to minimize or eliminate them if at all possible.
>>
>> Here is a rundown of observations and some attempts at troubleshooting so
>> far:
>>
>> Signs and symptoms:
>> - Voltage spikes in the digitized time streams of multitone frequency
>> combs. The glitches appear to be non-periodic, and vary in amplitude over
>> the full scale of the ADCs. They are present in both the I and Q channels,
>> but can be worse in a single channel. They are also observed, to a lesser
>> extent, when the I/Q inputs are terminated in 50 ohms. No glitches are
>> observed in the DAC output, which is looped directly back to the ADCs
>> during these measurements. The glitches only present in waveforms
>> containing more than a single frequency.
>>
>> - On an afflicted system, the glitches disappear when the clock is either
>> slowed to < ~430 MHz, or increased above ~530 MHz. On a system which is not
>> afflicted, the glitches can be induced by slowing the clock to below ~500
>> MHz.
>>
>> - They have not been remedied by swapping MUSIC boards, although their
>> characteristics differ somewhat between different board combinations. When
>> a MUSIC board is taken from an afflicted system and used with a reliable
>> Roach, no glitches are observed.
>>
>> - Glitches are not observed in five systems which have had their FPGA
>> fans removed and replaced with heat pipe assemblies. However, one of these
>> systems exhibited glitches when the mounting bolts on the FPGA heat sink
>> were overtightened by a small amount. When they were loosened, the glitches
>> subsided immediately.
>>
>> Attempts at troubleshooting:
>> - Firmware: Identical firmware used on each of the systems. Given the
>> correlation with clock rate, timing is a likely culprit. Using MSSGE, the
>> firmware compiles with a timing score of zero. However, the best case
>> positive slack is quite small (a few picoseconds). I've attempted to
>> increase this by using pblocks in PlanAhead, as well as the get lucky
>> approach with SmartXplorer, without much success. The ADC MMCM is
>> configured for high bandwidth, in accordance with a previous post on MUSIC
>> board glitches.
>>
>> - Hardware: As mentioned above, the glitches haven't been observed when
>> running with heat pipes instead of fans. While watching a live stream of
>> the ADC snap readout on one of the afflicted systems, I unplugged the power
>> leads to the FPGA fan. The spikes gradually subsided over a few seconds.
>> When the fan was powered on again, they returned on the same time scale.
>> This effect was not reproducible on an identical system.
>>
>> - We've had no luck using different synthesizers as clock sources,
>> filtering, attenuating or otherwise isolating the clock line to the MUSIC
>> boards.
>>
>> Much appreciated,
>> Sam Gordon
>> Astrophysics PhD candidate
>> Arizona State University
>>
>> --
>> You received this message because you are subscribed to the Google Groups
>> "[email protected]" group.
>> To unsubscribe from this group and stop receiving emails from it, send an
>> email to [email protected].
>> To post to this group, send email to [email protected].
>>
>

-- 
You received this message because you are subscribed to the Google Groups 
"[email protected]" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to [email protected].
To post to this group, send email to [email protected].

Reply via email to