PS
The source of HERA's 10MHz ref and 1PPS into the White Rabbit
switch is an old Trimble Thunderbolt GPS Disciplined clock
leftover from PAPER.
https://www.trimble.com/timing/thunderbolt-e.aspx


On Fri, 19 Oct 2018, Matt Dexter wrote:

Date: Fri, 19 Oct 2018 11:05:53 -0700 (Pacific Daylight Time)
From: Matt Dexter <"[email protected]"@berkeley.edu>
To: [email protected]
Subject: Re: [casper] SNAP Board clocking for a low-frequency array

Skimming the Meinberg manual finds reference to outputs that
are TTL levels into 50ohms,  TTL levels without load specified, and
2.5V TTL into 75 ohms.  I didn't study it enough to understand which
exact output has which drive spec. Meinberg's technical support should be able
to directly answer questions about the drive circuits and the
loads they can drive.

An old and simple 16way 1PPS driver design, schematics and Gerbers
included, may be found at
https://casper.berkeley.edu/wiki/16_way_1PPS_driver

The HERA project plans to use the White Rabbit Switch and
WR-LEN Endpoint from Seven Solutions for its 1PPS and 10MHz
distribution.
http://sevensols.com/index.php/timing-products/

Matt

PS.
Our lab has a collection of random synthesizers like
https://www.valonrf.com/frequency-synthesizer-6ghz.html
https://www.dsinstruments.com/store/products/category/rf-signal-generators/ SG6000E
OLED display ADF4350 signal generator RF source from eBay

On Fri, 19 Oct 2018, Nitish Ragoomundun wrote:

Date: Fri, 19 Oct 2018 13:45:34 +0400
From: Nitish Ragoomundun <[email protected]>
Reply-To: [email protected]
To: [email protected]
Subject: Re: [casper] SNAP Board clocking for a low-frequency array


Many thanks for your replies, Bob and Prof Inggs. Now we have a better idea how to tackle the issue.

Cheers.

On Fri, Oct 19, 2018 at 12:37 PM Michael Inggs <[email protected]> wrote:
      Hi Nitish

I am sure the Meinberg TTL will battle to drive 20 mA into the  SNAP. It is probably rated at a
few TTL loads.

For multiple boards, you will need to buffer the output of the Meinberg into a clock distribution network i.e. multiple output gate / driver leading to the number of boards you aim to drive as separate TTL channels. This is a bit pedantic, but just linking the Meinberg in parallel to a number of TTL inputs (check the Meinberg drive capability in TTL loads in the first place) will lead to multiple reflections and some jitter on the leading edge.

For our NeXtRAD multistatic radar that uses GPS synchronisation between nodes, we have implemented an ubiquitous Frequency Distribution Unit (FDU) that can swallow almost any 10 MHz or 100 MHz clock, at all the weird logic levels around, and then providing 10 and 100 MHz in 6 ports per voltage standard (5V, 3V3, sinewave). There is an optional 10x multiplier (low phase noise) for converting from 10 MHz to 100 MHz. Block diagram attached. You can implement any
subset of it. Can provide board layouts etc.

We also have a home made GPS Disciplined Oscillator that is proved to provide less that 4 ns rms jitter between nodes with common view satellites. It provides 1 pps, 10 and 100 MHz outputs (at various levels). Stephan Sandenbergh is the father of this, and has implemented some cunning fast lock mechanisms. Otherwise you will be there for hours if the power goes off.

Stephan also built a test jig for comparing two sources and plotting the Allen Variance. Be careful of low cost GPSDOs as they are designed for NTP applications in networks, where 15 ms is
all that is required.

We also have a great deal of experience and hardware (with results) of using White Rabbit to
synchronise receivers.

Regards

On Fri, 19 Oct 2018 at 09:04, Nitish Ragoomundun <[email protected]> wrote:

Hi all,

We are building a low-frequency array for the observation of the deuterium hyperfine line at 327.4 MHz with a bandwidth of 250 kHz. We intend to use SNAPs for acquisition. The boards will operate at full 12 channels input, thus the ADCs at 250 MSps. We will
subsequently decimate the data rate, as our working bandwidth is narrow.

Concerning the clock input for the SNAP,  https://casper.berkeley.edu/wiki/SNAP states the
following:

Digital 1 PPS: 50 ohm single-ended LVTTL logic levels
 *  SMATP13
* Vin-high 2.0 to 3.3 Volts. Low current drive sources, such as typical LVTTL or CMOS gates, probably can not supply the 40mA required to supply the 2.0V into the 50ohm
    load.
 *  Vin-low 0.0 to 0.8 Volts

Actually we considered buying the GPS-disciplined Meinberg M500 LANTIME(https://www.meinbergglobal.com/english/products/modular-railmount-ntp-server-ieee-1588-solution.htm) , which is advertised to output 1 PPS TTL levels. Now, our first question is whether the SNAP can work with this? Also, the note about low current drive sources is a little
confusing, can anyone shed some light here.

Secondly, we would like suggestions from anyone who has experience with clocking the SNAP. You see, we run a very tight budget and the M500 LANTIME clock is expensive. We would like to know if there is a less costly way to clock the SNAP and synchronise several boards.

Thanks.

Best regards,
Nitish Ragoomundun
Department of Physics
University of Mauritius

--
You received this message because you are subscribed to the Google Groups
"[email protected]" group.
To unsubscribe from this group and stop receiving emails from it, send an email to
[email protected].
To post to this group, send email to [email protected].



--
Michael Inggs
10 Devon Street, Simon's Town, South Africa. Tel: +27 21 786 1723 Fax: +27 21 786 1151  Skype:
mikings Cell: +27 83 776 7304"Ex Africa semper aliquid novi"

--
You received this message because you are subscribed to the Google Groups
"[email protected]" group.
To unsubscribe from this group and stop receiving emails from it, send an email to
[email protected].
To post to this group, send email to [email protected].

--
You received this message because you are subscribed to the Google Groups "[email protected]"
group.
To unsubscribe from this group and stop receiving emails from it, send an email to
[email protected].
To post to this group, send email to [email protected].



--
You received this message because you are subscribed to the Google Groups 
"[email protected]" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to [email protected].
To post to this group, send email to [email protected].

Reply via email to