Hi Heystek, >From an FPGA designers view: it means the gpio FPGA pin you have selected is not compatible with 3.3 LVCMOS. Your pin looks single-ended, but maybe you are using a differential pin and it expects a differential IO standard? Maybe select another gpio pin that you know to be single ended? I am not sure on the version of mlib_devel you are using, but are you selecting "ROACH2: gpio". You could also delete the suspect gpio yellow block, tie it high or low and then see if your model compiles. If it does then you know where to look. Just my 10c worth.
Anyway, HTH! Kind regards, Adam Isaacson South African Radio Astronomy Observatory (SARAO) Hardware Manager Cell: (+27) 825639602 Tel: (+27) 215067300 email: aisaac...@ska.ac.za On Fri, Mar 8, 2019 at 11:15 AM Heystek Grobler <heystekgrob...@gmail.com> wrote: > Hey Franco and Jack > > I have cheked that I have done the post install "fixes" > > I have traced the error to these: > > ERROR:NgdBuild:488 - Attribute value "LVCMOS33" is not an accepted value > for > attribute "IOSTANDARD" on "r2wb640mhz_roach_gpio_a_enable_not_ext<0>". > ERROR:NgdBuild:488 - Attribute value "LVCMOS33" is not an accepted value > for > attribute "IOSTANDARD" on "r2wb640mhz_roach_gpio_b_enable_not_ext<0>". > > Do you perhaps know how I can fix this? > > Heystek > > > On Thu, Mar 7, 2019 at 2:12 AM Jack Hickish <jackhick...@gmail.com> wrote: > >> Hi Heystek, >> >> In addition to Franco's point about post-installation tweaks, you might >> find more information if you look up above the "Number of errors: 2", where >> [hopefully] there will be more specific error messages. >> >> Cheers >> Jack >> >> On Wed, 6 Mar 2019 at 09:47, Franco <francocuro...@gmail.com> wrote: >> >>> I'm not sure but did you make the modifications required >>> post-installation: >>> https://github.com/casper-astro/tutorials_devel/wiki#modifications-to-be-run-after-installs >>> ? >>> >>> I remember having a similar error for not having the make -> gmake link. >>> >>> Franco >>> >>> On Tue, Mar 5, 2019 at 10:24 AM Heystek Grobler < >>> heystekgrob...@gmail.com> wrote: >>> >>>> Good day CASPERites >>>> >>>> I am trying to compile a deign for a ROACH2 but I get the >>>> following error: >>>> >>>> NGDBUILD Design Results Summary: >>>> Number of errors: 2 >>>> Number of warnings: 10272 >>>> >>>> Total REAL time to NGDBUILD completion: 2 min 48 sec >>>> Total CPU time to NGDBUILD completion: 2 min 41 sec >>>> >>>> One or more errors were found during NGDBUILD. No NGD file will be >>>> written. >>>> >>>> Writing NGDBUILD log file "system.bld"... >>>> ERROR:Xflow - Program ngdbuild returned error code 2. Aborting flow >>>> execution... >>>> gmake: *** [__xps/system_routed] Error 1 >>>> ERROR:EDK - >>>> Error while running "gmake -f system.make bits". >>>> Error using gen_xps_files (line 688) >>>> XPS failed. >>>> >>>> Does anyone perhaps know how to fix it? >>>> >>>> Thanks for the help >>>> >>>> Heystek >>>> >>>> >>>> >>>> -- >>>> You received this message because you are subscribed to the Google >>>> Groups "casper@lists.berkeley.edu" group. >>>> To unsubscribe from this group and stop receiving emails from it, send >>>> an email to casper+unsubscr...@lists.berkeley.edu. >>>> To post to this group, send email to casper@lists.berkeley.edu. >>>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "casper@lists.berkeley.edu" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to casper+unsubscr...@lists.berkeley.edu. >>> To post to this group, send email to casper@lists.berkeley.edu. >>> >> -- >> You received this message because you are subscribed to the Google Groups >> "casper@lists.berkeley.edu" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to casper+unsubscr...@lists.berkeley.edu. >> To post to this group, send email to casper@lists.berkeley.edu. >> > -- > You received this message because you are subscribed to the Google Groups " > casper@lists.berkeley.edu" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to casper+unsubscr...@lists.berkeley.edu. > To post to this group, send email to casper@lists.berkeley.edu. > -- You received this message because you are subscribed to the Google Groups "casper@lists.berkeley.edu" group. To unsubscribe from this group and stop receiving emails from it, send an email to casper+unsubscr...@lists.berkeley.edu. To post to this group, send email to casper@lists.berkeley.edu.
