Hello,

I'm now troubleshooting this ROACH2 system, in Mike's place.

I found out this script:

https://github.com/ska-sa/roach2_testing/blob/master/roach2_production_test/roach2_ats.py

It seems to have a menu for performing various tests on the ROACH2
board, including a PowerPC DRAM memory test.

It also seems to be able to program the board back to the factory state,
using the JTAG protocol over the USB port, which means it is independent
of having a working bootloader, DRAM, TFTP, etc.

I propose doing the memory test first.

Does it seems reasonable? Is this script safe to use?

It is referenced on this document:

"ROACH-2 Production Test Machine Setup"

https://docs.google.com/document/d/1tqw4C6uZ6EULl1OykTFL_vQTnK52UBr0aYqTg44E5wg/edit

Regards,

Cesar


Em 21/03/2019 10:15, John Ford escreveu:
> The message comes from uboot, so it's worth trying to reload that. 
> Otherwise you may have a true hardware failure.  :(
> 
> John
> 
> 
> On Tue, Mar 19, 2019 at 6:59 AM Michael Peel <[email protected]
> <mailto:[email protected]>> wrote:
> 
>     Hi Heystek,
> 
>     Thanks for the reply and the link. The memory error appears
>     immediately after the roach is turned on, before the option to stop
>     the autoboot appears. Sometimes it does continue a bit beyond that
>     before stalling, so I’ll look at trying to do a uboot update when it
>     next does that.
> 
>     The links to the images on the webpage don’t work (the casper svn no
>     longer exists?), are the latest versions stored elsewhere now -
>     perhaps they the ones on the ska-sa git?
> 
>     Thanks,
>     Mike
> 
>>     On 17 Mar 2019, at 14:40, Heystek Grobler
>>     <[email protected] <mailto:[email protected]>> wrote:
>>
>>     Hey Michael
>>
>>     Did you try this procedure?
>>
>>     https://casper.ssl.berkeley.edu/wiki/ROACH_kernel_uboot_update
>>
>>     Did you manage to solve it?
>>
>>     Heystek 
>>
>>     On Fri, Mar 15, 2019 at 5:45 PM Michael Peel <[email protected]
>>     <mailto:[email protected]>> wrote:
>>
>>         Hi all,
>>
>>         I’m currently trying to set up a ROACH2 (for the first time),
>>         and have run into a number of problems. The bottom line is
>>         that I’m currently getting this memory error message:
>>
>>         U-Boot 2011.06-rc2-00000-g2694c9d-dirty (Dec 04 2013 - 20:58:06)
>>         CPU: AMCC PowerPC 440EPx Rev. A at 533.333 MHz (PLB=133 OPB=66
>>         EBC=66)
>>          No Security/Kasumi support
>>          Bootstrap Option C - Boot ROM Location EBC (16 bits)
>>          32 kB I-Cache 32 kB D-Cache
>>         Board: ROACH2
>>         I2C: ready
>>         DRAM: 512 MiB
>>         Memory error at 00000000, wrote 00000000, read 273218ff !
>>
>>         This follows from the casperfpga software being able to
>>         connect to the ROACH2, but unable to load the .fpg file onto
>>         it. That led to me attempting to update the romfs using ‘run
>>         tftproot’, but it could not get an IP address from the
>>         computer (DHCP/dnsmasq configuration issues on RHEL7 that I
>>         still need to figure out), so it did not run the update.
>>         However, after that I got a kernel panic on the onboard
>>         software, so the roach no longer got to the login stage.
>>
>>         I then created a USB boot drive using:
>>         
>> https://github.com/ska-sa/roach2_nfs_uboot/blob/master/roach2-debian-fs-snapshot-24-10-2012.tar.gz
>>         and tried to boot the roach from that, however it stalled
>>         during the boot process, and on reset I got the above error
>>         message.
>>
>>         Any suggestions?
>>
>>         Thanks,
>>         Mike

-- 
You received this message because you are subscribed to the Google Groups 
"[email protected]" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to [email protected].
To post to this group, send email to [email protected].

Reply via email to