Hi Eamon,

That third file is, I think, some rogue configuration from testing which
should never have been committed to that repository.

I suspect the 80C threshold was set (by me!) based on a sample
configuration file from the KC705 development board and/or based on the
data sheet's 85C max temperature spec, derated a little and applied without
too much thought. There probably is scope to raise the temperature
threshold at least a little, but -- as pointed out by David -- improving
cooling would certainly seem like a better solution. FWIW, if you have the
ability to change the input voltage on your system you might also be able
to slightly improve DC/DC converter efficiency by changing the input
voltage.

Cheers
Jack

On Sun, 25 Jul 2021 at 03:19, Eamon Egan, Mr <[email protected]> wrote:

> Hello,
>
>
>
> We are having thermal shutdown problems we are pretty sure are coming from
> the fusion controllers, so I thought I’d have a look at the shutdown
> temperature thresholds to see if they could be raised.
>
>
>
> I went and loaded up the SNAP fusion power chip configuration files from
> https://github.com/jack-h/snap/tree/master/pwrctrl, and I have a couple
> of questions:
>
>
>
> 1. There are 3 files named as follows:
> UCD9248 5.8.0.11400 Address 52 Project File_gpio.xml
> UCD9248 5.8.0.11400 Address 53 Project File_gpio.xml
> UCD9248_addr_52d.xml
>
>
>
> Since there are two controllers (U40 and U42), what is the 3rd file for?
>
>
>
> 2. In the configurations, all of the rails are set for a maximum
> temperature of 80C; most of them are set to shut down and lock out (never
> restart) when this temperature is reached.
>
>
>
> All three of the switching module data sheets specify a maximum
> temperature of 85C. The 10A dual-output module datasheet indicates that
> this is a junction temperature; the other two don’t specify what
> temperature is measured.
>
>
>
> Does anyone know if the sensed temperature is intended to be the ambient
> temperature which is specified as max 85C, or some other temperature that
> we could run hotter than this? How was the 80C threshold arrived at?
>
>
>
> If need be, I can try and clarify this with TI.
>
>
>
> Best regards,
>
>
>
> Eamon
>
> --
> You received this message because you are subscribed to the Google Groups "
> [email protected]" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to [email protected].
> To view this discussion on the web visit
> https://groups.google.com/a/lists.berkeley.edu/d/msgid/casper/YQBPR0101MB4163C5F16C6F19BF2536C0629DE79%40YQBPR0101MB4163.CANPRD01.PROD.OUTLOOK.COM
> <https://groups.google.com/a/lists.berkeley.edu/d/msgid/casper/YQBPR0101MB4163C5F16C6F19BF2536C0629DE79%40YQBPR0101MB4163.CANPRD01.PROD.OUTLOOK.COM?utm_medium=email&utm_source=footer>
> .
>

-- 
You received this message because you are subscribed to the Google Groups 
"[email protected]" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to [email protected].
To view this discussion on the web visit 
https://groups.google.com/a/lists.berkeley.edu/d/msgid/casper/CAG1GKSncELR4uyAbrrOYMgH2qwryX-td72r9QpBB72Yh9UbjAQ%40mail.gmail.com.

Reply via email to