Bryan,
If you look at the configs R2 Loopback 0 (2.2.2.2) is in OSPF. Also, I
do I have reachability between R1-loopback0 to R2-loopback0. Below are the
outputs. I believe I see the issue. R1 and R2 are using 11.1.1.1 and
22.2.2.2 as there LDP Identifier respectively. However, since neither
network are advertised in OSPF the LDP neighbor relationship is not coming
up. However I tried using the command "mpls ldp router-id lo0" on both
router to change the LDP identifier which did not work. What can I do?
Thanks
R1 Outputs
R1#show mpls ldp discovery
Local LDP Identifier:
11.1.1.1:0
Discovery Sources:
Interfaces:
FastEthernet0/0 (ldp): xmit/recv
LDP Id: 22.2.2.2:0; no route
R1#sh ip ospf int brief
Interface PID Area IP Address/Mask Cost State Nbrs F/C
Lo0 1 0 1.1.1.1/32 1 LOOP 0/0
Lo1 1 0 11.1.1.1/24 1 LOOP 0/0
Fa0/0 1 0 10.1.12.1/24 10 BDR 1/1
R2 Outputs
R2#sh ip ospf int brief
Interface PID Area IP Address/Mask Cost State Nbrs F/C
Lo0 1 0 2.2.2.2/32 1 LOOP 0/0
Fa0/1 1 0 10.1.23.2/24 10 BDR 1/1
Fa0/0 1 0 10.1.12.2/24 10 DR 1/1
R2#ping 1.1.1.1 source lo0
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
Packet sent with a source address of 2.2.2.2
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 20/62/100 ms
R2#sh mpls ldp discovery
Local LDP Identifier:
22.2.2.2:0
Discovery Sources:
Interfaces:
FastEthernet0/0 (ldp): xmit/recv
LDP Id: 11.1.1.1:0
On Thu, Mar 11, 2010 at 1:57 PM, Bryan Bartik <[email protected]> wrote:
> Victor,
>
> I don't see your R2 loopbacks in OSPF, make sure you have reachability
> between the LDP router-ids. Can you ping from loopback to loopback? Give the
> output of "show mpls ldp discovery".
>
>
> On Thu, Mar 11, 2010 at 11:28 AM, Victor Reyes II <[email protected]>wrote:
>
>> I tried your suggesting and it did not work either.
>>
>> Message sent from my Droid
>>
>> On Mar 11, 2010 1:19 PM, "Wouter Prins" <[email protected]> wrote:
>>
>> hi!
>>
>> 1.) create the loopback 0 interface as /32
>> 2.) remove the ospf network type from the loopback interface
>>
>> Let me know if that works out. :)
>>
>> On 11 March 2010 19:13, Victor Reyes II <[email protected]> wrote:
>>
>>> >
>>> > Hi,
>>> >
>>> > I am trying to configure a simple MPLS config. However, I am have
>>> trouble getting the ...
>>> _______________________________________________
>>> For more information regarding industry leading CCIE Lab training, please
>>> visit www.ipexpert.com
>>>
>>>
>>
>>
>> --
>> Wouter Prins
>> [email protected]
>> CCIE #25628
>>
>>
>> _______________________________________________
>> For more information regarding industry leading CCIE Lab training, please
>> visit www.ipexpert.com
>>
>>
>
>
> --
> Bryan Bartik
> CCIE #23707 (R&S, SP), CCNP
> Sr. Support Engineer - IPexpert, Inc.
> URL: http://www.IPexpert.com
>
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
