I see the frame map for R5's link local addy but not R2's: frame-relay map ipv6 FE80::5 512 broadcast
On Wed, Dec 15, 2010 at 6:04 PM, Amer Mustafa <[email protected]> wrote: > > Also i am adding the ipv6 packet debug : > > ype escape sequence to abort. > Sending 5, 100-byte ICMP Echos to 2000:1:1:2B2B::2, timeout is 2 seconds: > Dec 15 22:59:50.119: IPv6: Looking up 2000:1:1:2B2B::2 [Source ::] in FIB > Dec 15 22:59:50.119: IPv6: FIB lookup for 2000:1:1:2B2B::2 succeeded. > if=Serial0/1/0.1, nexthop FE80::2 > Dec 15 22:59:50.119: IPv6-Sas: SAS picked source FD00:0:0:6419::5 for > 2000:1:1:2B2B::2 (Serial0/1/0.1) > Dec 15 22:59:50.119: IPv6-Fwd: nexthop FE80::2, > Dec 15 22:59:50.119: IPV6: source FD00:0:0:6419::5 (local) > Dec 15 22:59:50.119: dest 2000:1:1:2B2B::2 (Serial0/1/0.1) > Dec 15 22:59:50.119: traffic class 0, flow 0x0, len 100+0, prot 58, > hops 64, originating > *Dec 15 22:59:50.119: IPv6-Fwd: Encapsulation failed, could not queue for > resolution.* > Dec 15 22:59:52.119: IPv6: Looking up 2000:1:1:2B2B::2 [Source ::] in FIB > Dec 15 22:59:52.119: IPv6: FIB lookup for 2000:1:1:2B2B::2 succeeded. > if=Serial0/1/0.1, nexthop FE80::2 > Dec 15 22:59:52.119: IPv6-Sas: SAS picked source FD00:0:0:6419::5 for > 2000:1:1:2B2B::2 (Serial0/1/0.1) > Dec 15 22:59:52.119: IPv6-Fwd: nexthop FE80::2, > Dec 15 22:59:52.119: IPV6: source FD00:0:0:6419::5 (local) > Dec 15 22:59:52.119: dest 2000:1:1:2B2B::2 (Serial0/1/0.1) > Dec 15 22:59:52.119: traffic class 0, flow 0x0, len 100+0, prot 58, > hops 64, originating > Dec 15 22:59:52.119: IPv6-Fwd: Encapsulation failed, could not queue for > resolution. > Dec 15 22:59:54.119: IPv6: Looking up 2000:1:1:2B2B::2 [Source ::] in FIB > Dec 15 22:59:54.119: IPv6: FIB lookup for 2000:1:1:2B2B::2 succeeded. > if=Serial0/1/0.1, nexthop FE80::2 > Dec 15 22:59:54.119: IPv6-Sas: SAS picked source FD00:0:0:6419::5 for > 2000:1:1:2B2B::2 (Serial0/1/0.1) > Dec 15 22:59:54.119: IPv6-Fwd: nexthop FE80::2, > Dec 15 22:59:54.119: IPV6: source FD00:0:0:6419::5 (local) > Dec 15 22:59:54.119: dest 2000:1:1:2B2B::2 (Serial0/1/0.1) > Dec 15 22:59:54.119: traffic class 0, flow 0x0, len 100+0, prot 58, > hops 64, originating > Dec 15 22:59:54.119: IPv6-Fwd: Encapsulation failed, could not queue for > resolution. > Dec 15 22:59:56.119: IPv6: Looking up 2000:1:1:2B2B::2 [Source ::] in FIB > Dec 15 22:59:56.119: IPv6: FIB lookup for 2000:1:1:2B2B::2 succeeded. > if=Serial0/1/0.1, nexthop FE80::2 > Dec 15 22:59:56.119: IPv6-Sas: SAS picked source FD00:0:0:6419::5 for > 2000:1:1:2B2B::2 (Serial0/1/0.1) > Dec 15 22:59:56.119: IPv6-Fwd: nexthop FE80::2, > Dec 15 22:59:56.119: IPV6: source FD00:0:0:6419::5 (local) > Dec 15 22:59:56.119: dest 2000:1:1:2B2B::2 (Serial0/1/0.1) > Dec 15 22:59:56.119: traffic class 0, flow 0x0, len 100+0, prot 58, > hops 64, originating > Dec 15 22:59:56.119: IPv6-Fwd: Encapsulation failed, could not queue for > resolution. > Dec 15 22:59:58.119: IPv6: Looking up 2000:1:1:2B2B::2 [Source ::] in FIB > Dec 15 22:59:58.119: IPv6: FIB lookup for 2000:1:1:2B2B::2 succeeded. > if=Serial0/1/0.1, nexthop FE80::2 > Dec 15 22:59:58.119: IPv6-Sas: SAS picked source FD00:0:0:6419::5 for > 2000:1:1:2B2B::2 (Serial0/1/0.1) > Dec 15 22:59:58.119: IPv6-Fwd: nexthop FE80::2, > Dec 15 22:59:58.119: IPV6: source FD00:0:0:6419::5 (local) > Dec 15 22:59:58.119: dest 2000:1:1:2B2B::2 (Serial0/1/0.1) > Dec 15 22:59:58.119: traffic class 0, flow 0x0, len 100+0, prot 58, > hops 64, originating > Dec 15 22:59:58.119: IPv6-Fwd: Encapsulation failed, could not queue for > resolution. > > Success rate is 0 percent (0/5) > R5(config)# > ---------- Forwarded message ---------- > From: Amer Mustafa <[email protected]> > Date: Thu, Dec 16, 2010 at 1:55 AM > Subject: Workbook 1 ==> Task 32.7 (RIPng) > To: [email protected] > Cc: Jason Maynard <[email protected]> > > > *Workbook 1 ==> Task 32.7 (RIPng)* > ** > the task requires to advertise a new loop back on R2 in cisco275 and it > should be reachable from R5. > > *on R2 ======>* > > R2(config-if)#do show run int lo 1 > Building configuration... > Current configuration : 102 bytes > ! > interface Loopback1 > no ip address > ipv6 address 2000:1:1:2B2B::2/64 > ipv6 rip cisco275 enable > end > > *on R5 =======>* > ** > R5(config)#do show run int ser 0/1/0.1 > Building configuration... > Current configuration : 275 bytes > ! > interface Serial0/1/0.1 multipoint > description Use DLCI 512 here when mapped > ipv6 address FE80::5 link-local > ipv6 address FD00:0:0:6419::5/64 > ipv6 rip cisco275 enable > frame-relay map ipv6 FE80::5 512 broadcast > frame-relay map ipv6 FD00:0:0:6419::2 512 broadcast > end > > ======================================== > > > R5(config)#do show ipv6 route > IPv6 Routing Table - Default - 4 entries > Codes: C - Connected, L - Local, S - Static, U - Per-user Static route > B - BGP, M - MIPv6, R - RIP, I1 - ISIS L1 > I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary, D - EIGRP > EX - EIGRP external > O - OSPF Intra, OI - OSPF Inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 > ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 > *R 2000:1:1:2B2B::/64 [120/2] > * via FE80::2, Serial0/1/0.1 > C FD00:0:0:6419::/64 [0/0] > via Serial0/1/0.1, directly connected > L FD00:0:0:6419::5/128 [0/0] > via Serial0/1/0.1, receive > L FF00::/8 [0/0] > via Null0, receive > R5(config)# > > > BUT STILL NOT ABLE TO PING IT !??? > > R5(config)# do ping 2000:1:1:2b2b::2 > Type escape sequence to abort. > Sending 5, 100-byte ICMP Echos to 2000:1:1:2B2B::2, timeout is 2 seconds: > ..... > Success rate is 0 percent (0/5) > R5(config)# > > > *can anyone advice why ?* > > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
