Hi Marc, The router-id thing i don't know. Maybe it's because of IPv6 and it will only allow a router-id based on the link-local address you set? What does the interface output show ?
As for the routes, the only thing i see from a glance is that your R6 doesn't have a broadcast statement for ipv4. Maybe that's what's causing it ? > frame-relay map ipv6 FE80::2 602 broadcast > frame-relay map ip 141.41.26.5 602 <-- > frame-relay map ip 141.41.26.6 602 Regards, Alef > > ------------------------------ > > Message: 6 > Date: Mon, 18 Jul 2011 22:37:36 -0500 > From: marc abel <[email protected]> > To: [email protected] > Subject: [OSL | CCIE_RS] IPV6 problem > Message-ID: > <CANYR4zmKcj8d_oqvnH3BzTuw3ZUaw4x_=eaznnfgnxsxkzs...@mail.gmail.com> > Content-Type: text/plain; charset=ISO-8859-1 > > I have a simple hub and spoke topology R5-R2-R6 with R2 as the hub. I > am running eigrp and have neighbor relationships but no routes. What > am I doing wrong? One thing I notice is that I can put in the eigrp > router-id 5.5.5.5 or 6.6.6.6 on 5 and 6 but it never shows in the > running config. > > Below are the relevant configs and some show commands from R2, it is > the same from R5 and R6. > > > R2 (HUB) > _______________________ > ipv6 unicast-routing > ! > ipv6 router eigrp 256 > eigrp router-id 2.2.2.2 > no shutdown > ! > interface Serial0/1/0 > ip address 141.41.26.2 255.255.255.0 > encapsulation frame-relay > ipv6 address FE80::2 link-local > ipv6 address 2001:256::2/64 > ipv6 eigrp 256 > no ipv6 split-horizon eigrp 256 > frame-relay map ipv6 2001:256::6 206 > frame-relay map ipv6 2001:256::5 205 > frame-relay map ipv6 FE80::5 205 broadcast > frame-relay map ipv6 FE80::6 206 broadcast > frame-relay map ip 141.41.26.6 206 broadcast > frame-relay map ip 141.41.26.5 205 broadcast > frame-relay map ip 141.41.26.2 205 > no frame-relay inverse-arp > ! > interface Loopback6 > no ip address > ipv6 address 2001::2/64 > ipv6 eigrp 256 > end > > > > R5 > _______________________ > > ipv6 router eigrp 256 > no shutdown > ! > interface Serial0/1/0.1 multipoint > ip address 141.41.26.5 255.255.255.0 > ipv6 address FE80::5 link-local > ipv6 address 2001:256::5/64 > ipv6 eigrp 256 > frame-relay map ipv6 2001:256::6 502 > frame-relay map ipv6 2001:256::2 502 > frame-relay map ipv6 FE80::2 502 broadcast > frame-relay map ip 141.41.26.2 502 broadcast > frame-relay map ip 141.41.26.6 502 > frame-relay map ip 141.41.26.5 502 > no frame-relay inverse-arp > ! > interface Loopback6 > no ip address > ipv6 address 2001::5/64 > ipv6 eigrp 256 > end > > > > R6 > ________________________ > ipv6 router eigrp 256 > no shutdown > ! > interface Serial0/1/0 > ip address 141.41.26.6 255.255.255.0 > encapsulation frame-relay > ipv6 address FE80::6 link-local > ipv6 address 2001:256::6/64 > ipv6 eigrp 256 > frame-relay map ipv6 2001:256::5 602 > frame-relay map ipv6 2001:256::2 602 > frame-relay map ipv6 FE80::2 602 broadcast > frame-relay map ip 141.41.26.5 602 > frame-relay map ip 141.41.26.6 602 > no frame-relay inverse-arp > ! > interface Loopback6 > no ip address > ipv6 address 2001::6/64 > ipv6 eigrp 256 > end > > > R2(config-if)#do ping 2001:256::5 > > Type escape sequence to abort. > Sending 5, 100-byte ICMP Echos to 2001:256::5, timeout is 2 seconds: > !!!!! > Success rate is 100 percent (5/5), round-trip min/avg/max = 16/19/28 ms > R2(config-if)#do ping 2001:256::6 > > Type escape sequence to abort. > Sending 5, 100-byte ICMP Echos to 2001:256::6, timeout is 2 seconds: > !!!!! > > R2(config-if)#do show ipv6 eigrp nei > IPv6-EIGRP neighbors for process 256 > H Address Interface Hold Uptime SRTT RTO Q Seq > (sec) (ms) Cnt Num > 1 Link-local address: Se0/1/0 173 00:46:57 23 200 0 4 > FE80::6 > 0 Link-local address: Se0/1/0 172 00:48:48 24 200 0 7 > FE80::5 > > > R2(config-if)#do show ipv6 ro > IPv6 Routing Table - Default - 5 entries > Codes: C - Connected, L - Local, S - Static, U - Per-user Static route > B - BGP, M - MIPv6, R - RIP, I1 - ISIS L1 > I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary, D - EIGRP > EX - EIGRP external > O - OSPF Intra, OI - OSPF Inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 > ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 > C 2001::/64 [0/0] > via Loopback6, directly connected > L 2001::2/128 [0/0] > via Loopback6, receive > C 2001:256::/64 [0/0] > via Serial0/1/0, directly connected > L 2001:256::2/128 [0/0] > via Serial0/1/0, receive > L FF00::/8 [0/0] > via Null0, receive > > > End of CCIE_RS Digest, Vol 66, Issue 43 > *************************************** _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
