in your line config did you put no exec ? and autobaud ? On Thu, Mar 22, 2012 at 4:10 PM, rajaram <[email protected]> wrote:
> is baud rate is same ? > > On Thu, Mar 22, 2012 at 5:47 AM, Jay McMickle <[email protected] > >wrote: > > > Can you paste in your terminal lines config? > > > > Regards, > > Jay McMickle- CCNP,CCSP,CCDP > > Sent from iJay > > > > On Mar 22, 2012, at 5:03 AM, Mina Farid <[email protected]> wrote: > > > > > Hi People, > > > > > > > > > > > > I have just put together a home lab, all is OK except an issue I am > > having > > > with the access server > > > > > > The terminal server cannot connect the 2500 routers (backbones) I can > > login > > > to these routers using normal console cable with nothing special > > > > > > The terminal server can connect to all other servers with no issues! > The > > > message I am getting is BB1 open and then nothing and no output at all > > > > > > I have tried to swap cables with no luck > > > > > > > > > sh vers below > > > > > > > > > Cisco Internetwork Operating System Software > > > > > > IOS (tm) 3000 Software (IGS-I-L), Version 11.1(8), RELEASE SOFTWARE > (fc1) > > > > > > Copyright (c) 1986-1996 by cisco Systems, Inc. > > > > > > Compiled Thu 05-Dec-96 12:16 by tamb > > > > > > Image text-base: 0x0301FF88, data-base: 0x00001000 > > > > > > > > > ROM: System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE > > > > > > ROM: 3000 Bootstrap Software (IGS-RXBOOT), Version 10.2(8a), RELEASE > > > SOFTWARE (fc1) > > > > > > > > > Access-Server uptime is 1 hour, 43 minutes > > > > > > System restarted by power-on > > > > > > System image file is "flash:igs-i-l.111-8", booted via flash > > > > > > > > > cisco 2511 (68030) processor (revision D) with 2048K/2048K bytes of > > memory. > > > > > > Processor board ID 02280119, with hardware revision 00000000 > > > > > > Bridging software. > > > > > > X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. > > > > > > 1 Ethernet/IEEE 802.3 interface. > > > > > > 2 Serial network interfaces. > > > > > > 16 terminal lines. > > > > > > 32K bytes of non-volatile configuration memory. > > > > > > 8192K bytes of processor board System flash (Read ONLY) > > > > > > > > > Configuration register is 0x2102 > > > > > > > > > > > > Any ideas? > > > > > > > > > > > > > > > Cheers > > > > > > > > > Mena > > > _______________________________________________ > > > For more information regarding industry leading CCIE Lab training, > > please visit www.ipexpert.com > > > > > > Are you a CCNP or CCIE and looking for a job? Check out > > www.PlatinumPlacement.com > > > > > > http://onlinestudylist.com/mailman/listinfo/ccie_rs > > _______________________________________________ > > For more information regarding industry leading CCIE Lab training, please > > visit www.ipexpert.com > > > > Are you a CCNP or CCIE and looking for a job? Check out > > www.PlatinumPlacement.com > > > > http://onlinestudylist.com/mailman/listinfo/ccie_rs > > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com > > http://onlinestudylist.com/mailman/listinfo/ccie_rs > -- Edgar Díaz Orellana CCENT/CCNA/CCNA Security, CCNP en progreso, CCSP pausado. Kaspersky Administrator / Technical Specialist Microsoft Certified Professional. Celular : 09-94118996 skype: eorellan1969 _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
