also it is sparse mode. I think there is a command to enable join of two of the groups for sparse mode to work. These groups are enabled by default for dense mode. Something to look at.
On Monday, November 12, 2012, Keller Giacomarro <[email protected]> wrote: > Okay, I must be totally missing the boat here, but I can't get Multicast > over NBMA to work AT ALL. > > R2-----\ > -------- R1 > R3-----/ > > All interfaces are physical interfaces with static ipv4 mappings. R1 has > DLCIs to both spoke routers, and spoke routers only have DLCIs to R1. This > is as simple as I know how to get it. > > *** R1 *** > interface Serial1/0 > ip address 10.0.0.1 255.255.255.0 > ip pim dr-priority 1000 > ip pim nbma-mode > ip pim sparse-mode > encapsulation frame-relay > frame-relay map ip 10.0.0.3 103 broadcast > frame-relay map ip 10.0.0.2 102 broadcast > no frame-relay inverse-arp > ! > interface Loopback0 > ip address 1.1.1.1 255.255.255.0 > ! > ip pim rp-address 1.1.1.1 > > *** R2 *** > interface Serial1/0 > ip address 10.0.0.2 255.255.255.0 > ip pim sparse-mode > encapsulation frame-relay > frame-relay map ip 10.0.0.3 201 > frame-relay map ip 10.0.0.1 201 broadcast > ! > interface Loopback0 > ip address 2.2.2.2 255.255.255.255 > ip pim sparse-mode > ip igmp join-group 229.0.0.2 > ! > ip route 1.1.1.1 255.255.255.255 10.0.0.1 > ip pim rp-address 1.1.1.1 > > *** R3 *** > interface Serial1/0 > ip address 10.0.0.3 255.255.255.0 > ip pim sparse-mode > encapsulation frame-relay > frame-relay map ip 10.0.0.2 301 > frame-relay map ip 10.0.0.1 301 broadcast > ! > ip route 1.1.1.1 255.255.255.255 10.0.0.1 > ip pim rp-address 1.1.1.1 > > *** Testing *** > Ping is from R3 to 229.0.0.2, which is joined on R2. The first ping goes > through fine, all others drop until the mroute times out on R1. > > --- > R3(config)#do ping 229.0.0.2 re 10 > Type escape sequence to abort. > Sending 10, 100-byte ICMP Echos to 229.0.0.2, timeout is 2 seconds: > > Reply to request 0 from 2.2.2.2, 48 ms......... > R3(config)# > --- > > Debugs indicate that R2 (subscriber router) is sending a PIM Prune to R1 > (the hub/RP) as soon as the first packet is received. R2 retains the (S,G) > mapping with an incoming interface of s1/0, but the prune message causes R1 > to remove S1/0 from the OIL. Any packets after the first are dropped on R1 > due to the olist being null. > > I don't understand why the PIM Prune is being generated on R2 for R1 -- > isn't that the router that's sending the stream? Most of all, I don't > understand why something that seems so simple isn't working! > > In conclusion, I hate multicast! > > Appreciate any help you might be able to provide. =) > > Keller Giacomarro > [email protected] > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com > > http://onlinestudylist.com/mailman/listinfo/ccie_rs > -- Samir Idris _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
