I had a look at the diagram and then your initial email. If it is the connectivity between R2 and R3 loopback you are concerned about then why mention BB in your initial email? Also, can you mark v1 and v2 clearly? Only BB is running v1 and rest v2?
On Friday, December 28, 2012, Sheraz Sheraz <[email protected]> wrote: > Dear Samir, > > topology has already been shared, although im attaching it again. Task is as below. > > Task: R2 loopback 0 can access R3 loopback3 via frame-relay cloud make sure that this circuit goes down it regain connectivity in 5 second. > > Regards > Sheraz > > ________________________________ > Date: Fri, 28 Dec 2012 20:08:34 +1100 > Subject: Re: [OSL | CCIE_RS] TrunkLink Over EtherChannel > From: [email protected] > To: [email protected] > CC: [email protected]; [email protected] > > Sheraz, > > Where is the topology? I can't see any. > > On Friday, December 28, 2012, Sheraz Sheraz <[email protected]> wrote: >> Hi, >> >> Any update Marko, any one else who can figure out this task? CCIE guys please have a look! its challenge from my instructor!. >> >> Regards >> Sheraz >> >> From: [email protected] >> To: [email protected] >> CC: [email protected] >> Subject: RE: [OSL | CCIE_RS] TrunkLink Over EtherChannel >> Date: Wed, 26 Dec 2012 02:31:26 +0500 >> >> >> >> >> Dear Marko, >> >> topologies are attached. >> >> Regards >> Sheraz >> >>> From: [email protected] >>> Date: Tue, 25 Dec 2012 12:56:52 -0800 >>> Subject: Re: [OSL | CCIE_RS] TrunkLink Over EtherChannel >>> To: [email protected] >>> CC: [email protected] >>> >>> I lost you there a little bit. Can you post a drawing of the topology, please? >>> >>> -- >>> Marko Milivojevic - CCIE #18427 (SP R&S) >>> Senior CCIE Instructor - IPexpert >>> >>> On Tue, Dec 25, 2012 at 12:38 PM, Sheraz Sheraz <[email protected]> wrote: >>> > Hi, >>> > >>> > Is there any naive/champ who can solve this question? it is one of the CCIE task from RIP over frame-relay cloud.Please help me to figure out this task my instructor said no one can solve this tasks! basic timer can solve the problem but when it comes to BB it jeopardize the task. R2 is connected to R3 via FR cloud, secondary interfaces are directly connected to R4 & R4 is connected to R6 then BB is connected to R6 and using Rip 1 while other topology is using Rip v2. >>> > >>> > Task: R2 loopback 0 can access R3 loopback3 via frame-relay cloud make sure that this circuit goes down it regain connectivity in 5 second. >>> > >>> > Regards >>> > Sheraz >>> > >>> > _______________________________________________ >>> > For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com >>> > >>> > Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com >>> > >>> > http://onlinestudylist.com/mailman/listinfo/ccie_rs >> >> _______________________________________________ >> For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com >> >> Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com >> >> http://onlinestudylist.com/mailman/listinfo/ccie_rs >> > > -- > Samir Idris > -- Samir Idris _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
