Hi Scott, thanks for the reply, but I already tried what you suggested: no mgcp/mgcp removed the original 'TEI ASSIGNED' indication, I've also reset the GW on the CCM, but with no results (the 'test' dial-peer 999 was removed too). That was why I was thinking about a missing command somewhere. I suppose - as it's all ISDN related signaling - having a connection NM-HDV2 to NM-HDV shouldn't cause any problem? Either way, I've put back the NM-HDV instead of the NM-HDV2, and everything was working again... gonna keep it like that now, and if I find some extra time, I'll have another look at it - but Thank You for the help! Kind regards, Juan
________________________________ From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Scott Monasmith Sent: Monday, February 04, 2008 9:49 PM To: Juan Lopez Hernandez -X (jlopezhe - IBM - INS at Cisco) Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] MGCP PRI L2 issue Juan, Remove dial-peer v 999 pots - You don't need this for the PRI. Then do a 'no mgcp' then 'mgcp' - Maybe reset the gateway on CCM as well and you should be good to go. Cheers, Scott On Feb 2, 2008 3:30 PM, Juan Lopez Hernandez -X (jlopezhe - IBM - INS at Cisco) <[EMAIL PROTECTED]> wrote: Hi all, today, I swapped some HW in my lab, replacing the NM-HDV by NM-HDV2-1T1/E1. I had a working MGCP GW, connected via PRI to the PSTN. When using the NM-HDV2, I expercience a L2 issue (see debug below), causing all calls over that PRI to fail. I doubt that the HW is broken in this case, and it's a matter of a missing command... Does anybody have a clue or experienced the same - please let me know. I attached the config used on the GW - it's functionally not different from the working one when using the NM-HDV. ps: I have a PVDM2 sitting on the NM-HDV2, from which a part will be used as dspfarm ('voice-card 1') Kind regards, Juan isdn switch-type primary-ni voice-card 1 dspfarm dsp services dspfarm controller T1 1/1 framing esf linecode b8zs cablelength short 133 pri-group timeslots 1-3,24 service mgcp interface Serial1/1:23 no ip address isdn switch-type primary-ni isdn incoming-voice voice isdn bind-l3 ccm-manager no cdp enable voice-port 1/1:23 dial-peer voice 999 pots application mgcpapp incoming called-number . port 1/1:23 BR1-RTR#sh isdn status Global ISDN Switchtype = primary-ni %Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may not apply ISDN Serial1/1:23 interface dsl 0, interface ISDN Switchtype = primary-ni L2 Protocol = Q.921 0x0000 L3 Protocol(s) = CCM MANAGER 0x0003 Layer 1 Status: ACTIVE Layer 2 Status: TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED Layer 3 Status: 0 Active Layer 3 Call(s) BR1-RTR#debug isdn q921 debug isdn q921 is ON. BR1-RTR#term mon BR1-RTR# Feb 2 21:21:20.940: ISDN Se1/1:23 Q921: S7_T203_EXPIRY: Lost communication with remote. Feb 2 21:21:20.940: ISDN Se1/1:23 Q921: User TX -> RRp sapi=0 tei=0 nr=0 Feb 2 21:21:20.944: ISDN Se1/1:23 Q921: User RX <- RRp sapi=0 tei=0 nr=0 Feb 2 21:21:20.944: ISDN Se1/1:23 Q921: User TX -> RRf sapi=0 tei=0 nr=0 Feb 2 21:21:20.944: ISDN Se1/1:23 Q921: User RX <- RRf sapi=0 tei=0 nr=0 -- "There are only 10 types of people in the world: Those who understand binary, and those who don't"