You right. I missed the part of configuration. On Wed, Jun 25, 2008 at 6:07 AM, Nguyen Le <[EMAIL PROTECTED]> wrote:
> Transcoder can be invoked for BACD. You just have to do it through the > loopback interface. > > > > > On Tue, Jun 24, 2008 at 11:50 PM, Mehmet Tufekci <[EMAIL PROTECTED]> > wrote: > >> If you are using g729 from the gateway then the answer might be transcoder >> can not be invoked for BACD. >> >> >> On Jun 24, 2008, at 9:38 PM, Nguyen Le wrote: >> >> Try unchecking wait for h.245 terminal capabilities in your GK trunk >> configuration >> >> >> >> On Tue, Jun 24, 2008 at 6:41 PM, Jose Linero Welcker < >> [EMAIL PROTECTED]> wrote: >> >>> Hi: >>> >>> I am testing the B-ACD TCL in BR2, the connection between BR2 (CME) and >>> the CCM is trough a gatekeeper and when I called to the pilot number of the >>> script is not working. The local calls from the IP Phones registered to the >>> CME are working and the script is ok, the calls coming from the PSTN to the >>> BACD are working too. The configuration I have specifically to BACD is: >>> >>> application >>> service queue flash:app-b-acd-2.1.0.0.tcl >>> param queue-len 15 >>> param queue-manager-debugs 1 >>> param aa-hunt2 4210 >>> param number-of-hunt-grps 1 >>> ! >>> service aa flash:app-b-acd-aa-2.1.0.0.tcl >>> paramspace english index 1 >>> param number-of-hunt-grps 1 >>> param handoff-string aa >>> param dial-by-extension-option 1 >>> paramspace english language en >>> param max-time-vm-retry 2 >>> param aa-pilot 4500 >>> paramspace english location flash: >>> param second-greeting-time 60 >>> param welcome-prompt _bacd_welcome.au >>> param call-retry-timer 15 >>> param voice-mail 4600 >>> param max-time-call-retry 700 >>> param service-name queue >>> >>> dial-peer voice 10 voip >>> destination-pattern 4500 >>> session target ipv4:172.1.102.1 >>> dtmf-relay h245-alphanumeric >>> codec g711ulaw >>> no vad >>> ! >>> dial-peer voice 11 voip >>> service aa >>> incoming called-number 4500 >>> dtmf-relay h245-alphanumeric >>> codec g711ulaw >>> >>> The dial peer to receive the calls from CCM is: >>> >>> dial-peer voice 5 voip >>> translation-profile incoming DNIS >>> destination-pattern [23]... >>> session target ras >>> incoming called-number . >>> tech-prefix 1# >>> dtmf-relay h245-alphanumeric >>> >>> I have configured the transcodec: >>> >>> BR2-RTR-2821#sh sccp >>> SCCP Admin State: UP >>> Gateway IP Address: 142.101.66.1, Port Number: 2000 >>> IP Precedence: 5 >>> User Masked Codec list: None >>> Call Manager: 142.101.66.1, Port Number: 2000 >>> Priority: N/A, Version: 3.1, Identifier: 1 >>> Transcoding Oper State: ACTIVE - Cause Code: NONE >>> Active Call Manager: 142.101.66.1, Port Number: 2000 >>> TCP Link Status: CONNECTED, Profile Identifier: 1 >>> Reported Max Streams: 8, Reported Max OOS Streams: 0 >>> Supported Codec: g711ulaw, Maximum Packetization Period: 30 >>> Supported Codec: g711alaw, Maximum Packetization Period: 30 >>> Supported Codec: g729r8, Maximum Packetization Period: 60 >>> Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30 >>> >>> and the BR2 router is also been configured as IPIPGW: >>> >>> voice service voip >>> allow-connections h323 to h323 >>> allow-connections h323 to sip >>> allow-connections sip to h323 >>> allow-connections sip to sip >>> ! >>> >>> Doing a debug voice application I have this error: >>> >>> BR2-RTR-2821# >>> Jun 24 23:32:09.308: //-1//AFW_:/C_ServiceSession_Event_Handler: >>> Jun 24 23:32:09.308: //-1//AFW_:/AFW_Session_New: >>> Jun 24 23:32:09.308: //146//AFW_:/C_PackageSession_NewCall: Session >>> module listened by TclModule_45F87050_0_99922156 >>> Jun 24 23:32:09.308: //146//AFW_:/Open_SetupIndication: Calling #(3001), >>> Called #(852#4500), peer_tag(5) >>> Jun 24 23:32:09.308: //-1//AFW_:/C_PackageSession_GetSigPeer: >>> Jun 24 23:32:19.396: //146//AFW_:/AnyState_Disconnected: >>> Jun 24 23:32:19.396: //146//AFW_:/Session_Close: lastFailureCause 47 >>> Jun 24 23:32:19.396: //146//AFW_:/AFW_M_Session_Terminate: >>> Jun 24 23:32:19.396: //146//AFW_:/AFW_M_Session_Terminate: >>> lastFailureCause 47 >>> >>> Looking for the meaning of this error is: >>> >>> Last Disconnect Cause is "2F ", >>> Last Disconnect Text is "no resource (47)", >>> >>> I am stuck with this problem, any idea of what is the cause? >>> >>> Regards, >>> >>> Jose >>> >>> ------------------------------ >>> Invite your mail contacts to join your friends list with Windows Live >>> Spaces. It's easy! Try >>> it!<http://spaces.live.com/spacesapi.aspx?wx_action=create&wx_url=/friends.aspx&mkt=en-us> >>> >> >> >> >