You can send different ANI even if the VTP is set on the voice-port. The following would work
voice translation-rule 5 rule 1 /^\(3...\)$/ /331323\1/ on port voice translation-rule 6 rule 1 /^\(3...\)$/ /323\1/ on local DP voice translation-rule 7 rule 1 /^\(3...\)$/ /34331323\1/ on INT DP From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Ricardo Arevalo Sent: Friday, September 05, 2008 8:35 PM To: Jonathan Charles Cc: CCIE Voice Online Study List Subject: Re: [OSL | CCIE_Voice] Sending 10-digits on an E1 R2? An advise for this issue (or a tip) Unless requested different, try to define the translation-profile at outgoing dial-peer, so you could send different ANI based on destination number. This way, you could sent 7-digit number for any 911 or local call. And another longest ANI for international calls, 11-digits calling number for example= 7 digit + country code + 00. Try this same issue with CallManager. //r.a. On Fri, Sep 5, 2008 at 1:37 PM, Jonathan Charles <[EMAIL PROTECTED]> wrote: OK, nevermind, I fixed it with a translation... voice translation-rule 5 rule 1 /^\(3...\)$/ /331323\1/ ! voice translation-profile CLID translate calling 5 ! ! voice-port 0/0/0:1 translation-profile incoming PSTN-IN translation-profile outgoing CLID ! ! Jonathan On Fri, Sep 5, 2008 at 12:34 PM, Jonathan Charles <[EMAIL PROTECTED]> wrote: Calling from BR2 to BR1, I am only seeing 4-digits sent... here is the config of the E1: ! ! controller E1 0/0/0 ds0-group 1 timeslots 1-3 type r2-digital r2-semi-compelled ani cas-custom 1 dnis-digits min 10 max 10 ani-digits min 10 max 10 and the ephone I am calling from... ! ephone-dn 5 dual-line number 3003 no-reg primary description 3313233003 preference 2 call-forward busy 3600 call-forward noan 3600 timeout 10 corlist incoming phone2 ! ! ephone 3 username "Thing" password cisco mac-address 0004.9A3C.7800 button 1:5 ! On BR1 here is what I see... P3-BR1-RTR(config)# *Sep 5 18:24:47.858: ISDN Se0/0/0:23 Q931: RX <- SETUP pd = 8 callref = 0x0005 Bearer Capability i = 0x8090A2 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98381 Exclusive, Channel 1 Progress Ind i = 0x8583 - Origination address is non-ISDN Calling Party Number i = 0x0080, '3003' Plan:Unknown, Type:Unknown Called Party Number i = 0xA1, '6175232002' Plan:ISDN, Type:National *Sep 5 18:24:47.910: ISDN Se0/0/0:23 Q931: TX -> CALL_PROC pd = 8 callref = 0x8005 Channel ID i = 0xA98381 Exclusive, Channel 1 *Sep 5 18:24:47.914: ISDN Se0/0/0:23 Q931: TX -> ALERTING pd = 8 callref = 0x8005 Progress Ind i = 0x8088 - In-band info or appropriate now available P3-BR1-RTR(config)# P3-BR1-RTR(config)# P3-BR1-RTR(config)# P3-BR1-RTR(config)# Any ideas? Jonathan Mark Cardwell | Systems Engineer | MidAtlantic | Presidio Networked Solutions 7601 Ora Glen Drive, Suite 100, Greenbelt, MD 20770 | mailto:[EMAIL PROTECTED] D: 571.225.0132 | http://www.presidio.com/