I am using the below config, it is working for me, try it: --------------------------------------------------------- isdn switch-type primary-ni ! voice-card 0 no dspfarm ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! controller E1 0/2/0 pri-group timeslots 1-3,16 ! controller T1 0/3/0 framing esf linecode b8zs pri-group timeslots 1-3,24 ! controller T1 0/3/1 framing esf linecode b8zs pri-group timeslots 1-3,24 ! ! ! ! ! ! interface Serial0/2/0:15 no ip address isdn switch-type primary-ni isdn protocol-emulate network isdn incoming-voice voice no cdp enable ! interface Serial0/3/0:23 no ip address isdn switch-type primary-ni isdn protocol-emulate network isdn incoming-voice voice no cdp enable ! interface Serial0/3/1:23 no ip address isdn switch-type primary-ni isdn protocol-emulate network isdn incoming-voice voice no cdp enable ! ! voice-port 0/2/0:15 ! voice-port 0/3/0:23 ! voice-port 0/3/1:23 ! ! ! ! ! dial-peer voice 10 pots destination-pattern 915535.... incoming called-number . port 0/3/0:23 ! dial-peer voice 11 pots destination-pattern 902773.... port 0/3/1:23 ! dial-peer voice 12 pots destination-pattern 01176........ incoming called-number . port 0/2/0:15 ! ! ! ! telephony-service load 7960-7940 P00403020214 max-ephones 4 max-dn 12 ip source-address 192.168.41.1 port 2000 create cnf-files version-stamp 7960 Feb 19 2007 15:52:07 max-conferences 8 gain -6 ! ! ephone-dn 1 number 911 ! ! ephone-dn 2 number 0119876543210 ! ! ephone-dn 3 number 9024631111 ! ! ephone-dn 4 number 9164351111 ! ! ephone-dn 5 number 212555.... ! ! ephone 1 mac-address button 1:1 2:2 3:3 4:4 5:5 For the conection beteen PSTN router and your gw you need to create a crossover cable to connect the E1 / T1 make the connection as follows: 1----4 2----5 4----1 5----2 Regards, Bala.
--- On Wed, 22/10/08, Shadab Abbasi (moabbasi) <[EMAIL PROTECTED]> wrote: From: Shadab Abbasi (moabbasi) <[EMAIL PROTECTED]> Subject: Re: [OSL | CCIE_Voice] FW: PSTN Gateway & Backbone GK configuration To: "marwa" <[EMAIL PROTECTED]>, ccie_voice@onlinestudylist.com Date: Wednesday, 22 October, 2008, 4:06 PM Thanks Marwa, I got the same at the below mentioned location. Seeing the configuration, I found that translation-profile is applied under voice-ports, however NO translation-profile is created; just seeing translation-rules??? Any advice! -Shadab From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of marwa Sent: Wednesday, October 22, 2008 3:51 PM To: Shadab Abbasi (moabbasi); ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] FW: PSTN Gateway & Backbone GK configuration Hello, You can find the initial configurations for all the devices in the Proctor Labs support forum: http://proctorlabs.com/forum/ To access the forum, simply create a Proctor Labs account, which is free of charge, and use those credentials to enter the support forum. You'll find the configs you're looking for in the Voice > FAQ section. Marwa ----- Original Message ----- From: Shadab Abbasi (moabbasi) To: ccie_voice@onlinestudylist.com Sent: Wednesday, October 22, 2008 10:54 AM Subject: [OSL | CCIE_Voice] FW: PSTN Gateway & Backbone GK configuration Hello Experts, I am setting up my LAB & planning to run PSTN GW & Backbone (PSTN) – GK on the same router (2821) Can someone help me out with the configuration or sample? Regards, Shadab Get your preferred Email name! Now you can @ymail.com and @rocketmail.com. http://mail.promotions.yahoo.com/newdomains/aa/
