Hi Greg, As u can see my configs, no I don't have.
when I press message button, I can connect to pilot number , but I cannot hear any thing, even I can see call connects to pilot number form sh call active voice Jeremy On Sat, Nov 15, 2008 at 7:18 PM, Greg Miglucci (gmiglucc) < [EMAIL PROTECTED]> wrote: > You have no dialplan-pattern under telephony service or voice > translation-rules? > > ------------------------------ > *From:* jeremy co [mailto:[EMAIL PROTECTED] > *Sent:* Saturday, November 15, 2008 12:24 AM > *To:* Hardesty, Scott > *Cc:* Greg Miglucci (gmiglucc); CCIE Voice Maillist > > *Subject:* Re: [OSL | CCIE_Voice] CUE Wired problem: call to voice > pilotnumberworks, but message button not working. > > Hi, > > I added that, but I ran transcoder for other purposes, I don't think that > it is related to voice mail. > > > Any way, wired thing is when I press message button I can see it dialed > pilot number and then connected ,but I cannot hear anything. > > However, when I call 4444 , every thing is fine. > > > > Jeremy > > On Sat, Nov 15, 2008 at 4:06 PM, Hardesty, Scott <[EMAIL PROTECTED]>wrote: > >> I do not see your XCODER defined in CME. Try adding sdspfarm tag 1 >> XCODER under Telephony-service. >> >> >> >> >> >> *Scott Hardesty | Cisco Engineer | MidAtlantic | Presidio Networked >> Solutions* >> >> *7601 Ora Glen Drive, Suite 100, Greenbelt, MD 20770 | >> [EMAIL PROTECTED] >> >> *D: 301.313.2041 | C: 443.789.1219 | www.presidio.com* >> >> ** >> >> >> >> ------------------------------ >> >> *From:* [EMAIL PROTECTED] [mailto: >> [EMAIL PROTECTED] *On Behalf Of *jeremy co >> *Sent:* Saturday, November 15, 2008 12:00 AM >> *To:* Greg Miglucci (gmiglucc) >> *Cc:* CCIE Voice Maillist >> *Subject:* Re: [OSL | CCIE_Voice] CUE Wired problem: call to voice >> pilotnumberworks, but message button not working. >> >> >> >> Hi, >> >> I forgot to mention that when I press message button , call connects to >> voice pilot number but I cannot hear anything >> >> Here is the config: >> >> ! >> voice service voip >> allow-connections h323 to h323 >> allow-connections h323 to sip >> allow-connections sip to h323 >> ! >> ! >> >> ! >> ! >> ! >> mgcp >> ! >> sccp local FastEthernet0/0.200 >> sccp ccm 200.0.0.254 identifier 1 >> sccp >> ! >> sccp ccm group 1 >> associate ccm 1 priority 1 >> associate profile 1 register XCODER >> ! >> dspfarm profile 1 transcode >> codec g711ulaw >> codec g711alaw >> codec g729ar8 >> codec g729abr8 >> codec g729r8 >> codec g729br8 >> maximum sessions 4 >> associate application SCCP >> ! >> ! >> dial-peer voice 5000 pots >> destination-pattern 0982133335... >> direct-inward-dial >> forward-digits 8 >> ! >> dial-peer voice 4000 pots >> destination-pattern 061388884... >> direct-inward-dial >> forward-digits 4 >> ! >> dial-peer voice 30 pots >> destination-pattern 01124344... >> port 1/2:0 >> forward-digits 8 >> ! >> dial-peer voice 200 pots >> incoming called-number . >> direct-inward-dial >> port 1/2:0 >> ! >> dial-peer voice 600 voip >> destination-pattern 2222 >> session target ras >> dtmf-relay h245-alphanumeric >> ! >> dial-peer voice 999 voip >> destination-pattern 4444 >> session protocol sipv2 >> session target ipv4:200.0.0.100 >> dtmf-relay sip-notify >> codec g711ulaw >> no vad >> ! >> dial-peer voice 1001 voip >> destination-pattern 7000 >> session protocol sipv2 >> session target ipv4:200.0.0.100 >> dtmf-relay sip-notify >> codec g711ulaw >> no vad >> ! >> dial-peer voice 7878 voip >> destination-pattern 800[01].... >> session protocol sipv2 >> session target ipv4:114.0.0.0.254 >> dtmf-relay sip-notify >> codec g711ulaw >> no vad >> ! >> gateway >> timer receive-rtp 1200 >> ! >> sip-ua >> ! >> ! >> ! >> ! >> gatekeeper >> zone local FXSZONE abc.com 7.7.7.7 invia IPIPGWZONE outvia IPIPGWZONE >> enable-intrazone >> zone local CCMZONE abc.com >> zone local HQZONE abc.com >> zone local IPIPGWCCMZONE abc.com >> zone local IPIPGWZONE abc.com >> zone prefix HQZONE 011* >> zone prefix IPIPGWCCMZONE 3... >> gw-type-prefix 1#* default-technology >> no use-proxy FXSZONE default inbound-to terminal >> no use-proxy FXSZONE default outbound-from terminal >> bandwidth interzone zone CCMZONE 144 >> no shutdown >> ! >> ! >> telephony-service >> max-ephones 10 >> max-dn 200 >> ip source-address 200.0.0.254 port 2000 >> sdspfarm units 1 >> sdspfarm transcode sessions 2 >> create cnf-files version-stamp 7960 Mar 02 2002 04:09:38 >> voicemail 4444 >> mwi relay >> max-conferences 4 gain -6 >> web admin system name admin secret 5 $1$fS6t$7Pfc17AMenIo5ISKL3w2N0 >> ! >> ! >> ephone-dn 38 >> number 1000 >> ! >> ! >> ephone-dn 70 >> number 9911 >> call-forward noan 4444 timeout 10 >> ! >> >> ! >> ephone-dn 80 >> number 8000.... >> mwi on >> ! >> ! >> ephone-dn 81 >> number 8001.... >> mwi off >> ! >> ! >> ephone 1 >> username "pstn" password cisco >> mac-address 0030.94C2.BFB1 >> button 1:70 >> ! >> >> >> >> Jeremy >> >> On Sat, Nov 15, 2008 at 3:40 PM, Greg Miglucci (gmiglucc) < >> [EMAIL PROTECTED]> wrote: >> >> Post your telephony-service config and ephone-dn and dial-peer config. >> Also are you using dial-plan pattern under teleph-service? If so you need >> to make sure you have appropriate translation-rules. >> >> >> ------------------------------ >> >> *From:* [EMAIL PROTECTED] [mailto: >> [EMAIL PROTECTED] *On Behalf Of *jeremy co >> *Sent:* Friday, November 14, 2008 11:28 PM >> *To:* CCIE Voice Maillist >> *Subject:* Re: [OSL | CCIE_Voice] CUE Wired problem: call to voice >> pilotnumber works, but message button not working. >> >> I forgot to mention that when I press message button , call even connected >> to voice pilot number but I cannot hear anything >> >> >> Jeremy >> >> On Sat, Nov 15, 2008 at 3:12 PM, jeremy co <[EMAIL PROTECTED]> >> wrote: >> >> Hi, >> >> When I call to voice pilot number, it works, but when hit message button >> it wouldn't work. >> >> >> Can someone shed light on what may cause this issue? >> >> I restarted cue and phones but it's not working. >> >> >> Jeremy >> >> >> >> >> > >
