call-forward is a must. It will not work without it. You also need to make sure your transcoder is working right. If you call from a CME phone to CUE you know the dial-peer for CUE is ok. That rules that out. Then is it something with the Xcoder or you are missing the call-forward pattern .T in your telephony-service.
On Sun, Nov 23, 2008 at 12:34 PM, Norma Exel <[EMAIL PROTECTED]> wrote: > don't think the transfer pattern matters since Pardeep is dialing directly > to 4111 from a CM phone. perhaps the answer lies with the translation > pattern. > > Pardeep, did you try dialing from a CME phone to 4111? What happens then? > > > ----- Original Message ----- > From: "Ryan Trauernicht" > To: [EMAIL PROTECTED] > Cc: "Pardeep Singh \(pardsing\)" , ccie_voice@onlinestudylist.com > Subject: Re: [OSL | CCIE_Voice] Can't call to CUE pilot number from HQ > Date: Thu, 20 Nov 2008 19:20:43 -0600 > > you need to put a > call-forward pattern .T > > in your telephony-service > > On Thu, Nov 20, 2008 at 6:57 AM, <[EMAIL PROTECTED]> wrote: > >> why do you need to bind sip to loopback interface? >> i will put allow sip to h323, s to s and h323 to h323 >> >> sara >> >> *"Pardeep Singh (pardsing)" <[EMAIL PROTECTED]>* wrote: >> >> Team, >> >> I am having an issues when I call from my HQ site to CME using Gatekeeper >> Trunk over to CUE pilot number. >> >> Here is the call flow: >> HQ Phone-->>>dial 4001>>>>GK Trunk>>>>>CME = Call is successful >> HQ Phone--->>>dial 4111>>>>GK Trunk>>>>>CME>>>>CUE PILOT NUMBER = Call >> give this error back once I hang up the call over at CUCM Phone. >> >> This is the error I get on CME router: >> >> %SDP-3-SDP_PTR_ERROR: Recieved invalid SDP pointer form application. >> Unable to process. -Traceback= 0x41032A60 0x40EC8B58 on and on >> >> My configs: >> >> voice service voip >> allow-connections h323 to sip >> sip >> bind control source-interface Loopback0 >> bind media source-interface Loopback0 >> >> >> sccp local FastEthernet0/0.101 >> sccp ccm 142.33.66.1 identifier 1 >> sccp >> ! >> sccp ccm group 1 >> associate ccm 1 priority 1 >> associate profile 1 register mtp123456789 >> ! >> dspfarm profile 1 transcode >> codec g711ulaw >> codec g711alaw >> codec g729ar8 >> codec g729abr8 >> codec g729r8 >> maximum sessions 8 >> associate application SCCP >> >> dial-peer voice 100 voip >> translation-profile incoming FROMGK >> destination-pattern 2...$ >> session target ras >> incoming called-number . <<<<<<<<<<<<<<<< not using the default one >> tech-prefix 5# >> dtmf-relay h245-alphanumeric >> no vad >> >> dial-peer voice 200 voip >> destination-pattern 4111$ >> session protocol sipv2 >> session target ipv4:142.707.77.253 >> incoming called-number 800[01].... >> dtmf-relay sip-notify >> codec g711ulaw >> no vad >> >> telephony-service >> ip source-address 142.33.66.1 port 2000 >> system message Your current options >> sdspfarm units 1 >> sdspfarm transcode sessions 8 >> sdspfarm tag 1 mtp123456789 >> >> >> >> >> ------------------------------ >> Power up the Internet with Yahoo! >> Toolbar.<http://pr.mail.yahoo.co.jp/toolbar/> >> >> > > -- Be Yourself @ mail.com! > Choose From 200+ Email Addresses > Get a *Free* Account at www.mail.com <http://www.mail.com/Product.aspx>! >