How many PVDM do you have if your router and what are the type? #sh diag
should give one this information, with that you will be able to calculate the number of DSPs in your router. Note: That PVDM2-16; i.e. 16 channels PVDM version 2 contain only 1 DSP. As a rule, you cannot configure one DSP for both conferencing and transcoding. You might think this is too restrictive, until you realize that in the 6608 module all DSPs in a single port must be dedicated either to conferencing or to transcoding - no sharing. If you only have one PVDM2-16 module, your best bet is to upgrade. I had that limitation and error in my current 2811 that came with factory installed 1 PVDM2-16 and the only way I was able to get around it was to upgrade, tweaking the complexity mode between high, medium or flex can yied more codec channels, but you cannot get around the DSP-sharing limitation with that. See if this document will be of any help. http://www.toltec.eu/voipguides/High-Density%20Packet%20Voice%20Digital%20Signal%20Processor%20modules.pdf Tech Guy ----- Original Message ----- From: Erwan Erwan To: ccie_voice@onlinestudylist.com ; anil batra Sent: Wednesday, April 01, 2009 2:40 PM Subject: Re: [OSL | CCIE_Voice] dspfarm profile conference ? hi Anil, they have 16 DSP , use for 3 channel T1 only ( I shut down the other T1) ------ ----------------------------FLEX VOICE CARD 0 ------------------------------ *DSP VOICE CHANNELS* DSP DSP DSPWARE CURR BOOT PAK TX/RX TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABRT PACK COUNT ===== === == ======== ======= ===== ======= === == ========= == ==== ============ C5510 001 01 None 4.4.15 idle idle 0 0 0 0/0 C5510 001 02 None 4.4.15 idle idle 0 0 0 0/0 C5510 001 03 None 4.4.15 idle idle 0 0 0 0/0 C5510 001 04 None 4.4.15 idle idle 0 0 0 0/0 C5510 001 05 None 4.4.15 idle idle 0 0 0 0/0 C5510 001 06 None 4.4.15 idle idle 0 0 0 0/0 C5510 001 07 None 4.4.15 idle idle 0 0 0 0/0 C5510 001 08 None 4.4.15 idle idle 0 0 0 0/0 C5510 001 09 None 4.4.15 idle idle 0 0 0 0/0 C5510 001 10 None 4.4.15 idle idle 0 0 0 0/0 C5510 001 11 None 4.4.15 idle idle 0 0 0 0/0 C5510 001 12 None 4.4.15 idle idle 0 0 0 0/0 C5510 001 13 None 4.4.15 idle idle 0 0 0 0/0 C5510 001 14 None 4.4.15 idle idle 0 0 0 0/0 C5510 001 15 None 4.4.15 idle idle 0 0 0 0/0 C5510 001 16 None 4.4.15 idle idle 0 0 0 0/0 ------------------------END OF FLEX VOICE CARD 0 ---------------------------- tks --- On Tue, 3/31/09, anil batra <anil...@yahoo.com> wrote: From: anil batra <anil...@yahoo.com> Subject: Re: [OSL | CCIE_Voice] dspfarm profile conference ? To: ccie_voice@onlinestudylist.com, e_er...@yahoo.com Date: Tuesday, March 31, 2009, 5:51 AM How many DSP u hv , how many T1/E1 you are using .....seems like you are running short of DSP's --- On Tue, 3/31/09, Erwan Erwan <e_er...@yahoo.com> wrote: From: Erwan Erwan <e_er...@yahoo.com> Subject: [OSL | CCIE_Voice] dspfarm profile conference ? To: ccie_voice@onlinestudylist.com Date: Tuesday, March 31, 2009, 3:16 AM hi, I config the dspfarm for conference in 2811 -------------------------- voice-card 0 dsp service dspfarm dspfarm profile 1 conference codec g711ulaw codec g711alaw no codec g729abr8 no codec g729br8 no codec gsmfr max session 2 associate application SCCP no shut ------------------ I have not config any transcoding yet but the " max session" only 0 , mean do not work any idea/workaround ?