Thanks so much. That did the trick. CME now works as PSTN hub accepting inbound calls.
Cheers,Padhu ________________________________ From: kapil atrish [mailto:nice_cha...@yahoo.com] Sent: Thursday, May 28, 2009 11:30 AM To: Padmanabhan, Padhu; ccieid1ot Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] Problem with outgoing calls from Branch via T1 Pri to simulated PSTN router That's a common issue. Create one DP on CME as following: dial-peer voice xxx pots incoming called-nu . direct-inward-dial ! --- On Thu, 5/28/09, ccieid1ot <ccieid...@gmail.com> wrote: From: ccieid1ot <ccieid...@gmail.com> Subject: Re: [OSL | CCIE_Voice] Problem with outgoing calls from Branch via T1 Pri to simulated PSTN router To: "Padmanabhan, Padhu" <pa...@ti.com> Cc: "ccie_voice@onlinestudylist.com" <ccie_voice@onlinestudylist.com> Date: Thursday, May 28, 2009, 10:20 AM Just add another dial-peer for 911 with forward-digt all. On Wed, May 27, 2009 at 5:09 PM, Padmanabhan, Padhu <pa...@ti.com</mc/compose?to=pa...@ti.com>> wrote: > Hi, > > > > I am just getting started with my voice lab preps...I have a branch router > connected via WAN as well via T-1(crossover) to PSTN simulator running CME. > > I am unable to call simulated phones lines on the CME using the T-1 pri from > branch. As soon as I dial 911 it goes into connected state from Branch-1. > > > > However from the CME /PSTN I can call inbound to the BR1 phones. > > > > Pasted below is relevant config. BR1 router configured as h323 gw and added > to RG-RL-RP. Pattern 911 added to partition and included in the CSS for the > > BR1 phone. > > > > Any ideas?. > > > > Thanks,Padhu > > > > Branch-1: > > isdn switch-type primary-ni > > > > voice class h323 1 > > h225 timeout tcp establish 3 > > > > controller T1 1/0/0 > > pri-group timeslots 1-24 > > description connection from BR1 to PSTN > > > > interface Serial1/0/0:23 > > no ip address > > encapsulation hdlc > > isdn switch-type primary-ni > > isdn incoming-voice voice > > no cdp enable > > > > dial-peer voice 999 pots > > description Calls to PSTN using Local gateway > > destination-pattern .T > > incoming called-number . > > direct-inward-dial > > port 1/0/0:23 > > ! > > dial-peer voice 1 voip > > voice-class h323 1 > > incoming called-number . > > dtmf-relay h245-alphanumeric > > ! > > dial-peer voice 775 voip > > destination-pattern 775255.... > > voice-class h323 1 > > session target ipv4:10.1.40.10 > > > > pstn-sim: > > isdn switch-type primary-ni > > isdn gateway-max-interworking > > > > voice class h323 1 > > h225 timeout tcp establish 3 > > > > controller T1 0/0 > > framing esf > > clock source internal > > linecode b8zs > > cablelength short 133 > > pri-group timeslots 1-24 > > description Connection to BR1 > > > > interface Serial0/0:23 > > no ip address > > encapsulation hdlc > > isdn switch-type primary-ni > > isdn protocol-emulate network > > isdn incoming-voice voice > > no cdp enable > > > > dial-peer voice 775 pots > > description calls to BR1 > > destination-pattern 775255.... > > incoming called-number . > > port 0/0:23 > > forward-digits all > > > > telephony-service > > max-ephones 8 > > max-dn 30 > > ip source-address 10.1.99.1 port 2000 > > system message CME as PSTN Simulator > > max-conferences 8 gain -6 > > transfer-system full-consult > > create cnf-files version-stamp Jan 01 2002 00:00:00 > > ! > > ! > > ephone-dn 1 > > number 911 > > label Emergency_911 > > > > ephone 1 > > device-security-mode none > > mac-address 0002.FD65.9D5B > > button 1:1 2:2 3:3 4:4 > > button 5:5 6:6
